Abstract: In order to improve the simulation effects of space cold
black environment, this paper described a rectangular channel plate
heat sink. By using fluid mechanics theory and finite element method,
the internal fluid flow and heat transfer in heat sink was numerically
simulated to analyze the impact of channel structural on fluid flow and
heat transfer. The result showed that heat sink temperature uniformity
is well, and the impact of channel structural on the heat sink
temperature uniformity is not significant. The channel depth and
spacing are important factors which affect the fluid flow and heat
transfer in the heat sink. The two factors of heat transfer and resistance
need to be considered comprehensively to determine the optimal flow
structure parameters.
Abstract: In the present study, Convective heat transfer
coefficient and pressure drop of Al2O3/water nanofluid in laminar
flow regime under constant heat flux conditions inside a circular tube
were experimentally investigated. Al2O3/water nanofluid with 0.5%
and 1% volume concentrations with 15 nm diameter nanoparticles
were used as working fluid. The effect of different volume
concentrations on convective heat transfer coefficient and friction
factor was studied. The results emphasize that increasing of particle
volume concentration leads to enhance convective heat transfer
coefficient. Measurements show the average heat transfer coefficient
enhanced about 11-20% with 0.5% volume concentration and
increased about 16-27% with 1% volume concentration compared to
distilled water. In addition, the convective heat transfer coefficient of
nanofluid enhances with increase in heat flux. From the results, the
average ratio of (fnf/fbf) was about 1.10 for 0.5% volume
concentration. Therefore, there is no significant increase in friction
factor for nanofluids.
Abstract: This work aims to test the application of computational fluid dynamics (CFD) modeling to fixed bed catalytic cracking reactors. Studies of CFD with a fixed bed design commonly use a regular packing with N=2 to define bed geometry. CFD allows us to obtain a more accurate view of the fluid flow and heat transfer mechanisms present in fixed bed equipment. Naphtha was used as feedstock and the reactor length was 80cm. It is divided in three sections that catalyst bed packed in the middle section of the reactor. The reaction scheme was involved one primary reaction and 24 secondary reactions. Because of high CPU times in these simulations, parallel processing have been used. In this study the coke formation process in fixed bed and empty tube reactor was simulated and coke in these reactors are compared. In addition, the effect of steam ratio and feed flow rate on coke formation was investigated.
Abstract: A rigorous two-dimensional model is developed for simulating the operation of a less-investigated type steam reformer having a considerably lower operating Reynolds number, higher tube diameter, and non-availability of extra steam in the feed compared with conventional steam reformers. Simulation results show that reasonable predictions can only be achieved when certain correlations for wall to fluid heat transfer equations are applied. Due to severe operating conditions, in all cases, strong radial temperature gradients inside the reformer tubes have been found. Furthermore, the results show how a certain catalyst loading profile will affect the operation of the reformer.
Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.
Abstract: Numerical simulations are performed for laminar
continuous and pulsed jets impinging on a surface in order to
investigate the effects of pulsing frequency on the heat transfer
characteristics. The time-averaged Nusselt number of pulsed jets is
larger in the impinging jet region as compared to the continuous jet,
while it is smaller in the outer wall jet region. At the stagnation point,
the mean and RMS Nusselt numbers become larger and smaller,
respectively, as the pulsing frequency increases. Unsteady behaviors
of vortical fluid motions and temperature field are also investigated to
understand the underlying mechanisms of heat transfer enhancement.
Abstract: This investigation examines the effect of the sintering
temperature curve in manufactured nickel powder capillary structure
(wick) for a loop heat pipe (LHP). The sintering temperature curve is
composed of a region of increasing temperature; a region of constant
temperature and a region of declining temperature. The most important
region is that in which the temperature increases, as an index in the
stage in which the temperature increases. The wick of nickel powder is
manufactured in the stage of fixed sintering temperature and the time
between the stage of constant temperature and the stage of falling
temperature. When the slope of the curve in the region of increasing
temperature is unity (equivalent to 10 °C/min), the structure of the
wick is complete and the heat transfer performance is optimal. The
result of experiment test demonstrates that the heat transfer
performance is optimal at 320W; the minimal total thermal resistance
is approximately 0.18°C/W, and the heat flux is 17W/cm2; the internal
parameters of the wick are an effective pore radius of 3.1 μm, a
permeability of 3.25×10-13m2 and a porosity of 71%.
Abstract: This study deals with Computational Fluid Dynamics
(CFD) studies of the interactions between the air flow and louvered
fins which equipped the automotive heat exchangers. 3D numerical
simulation results are obtained by using the ANSYS Fluent 13.0 code
and compared to experimental data. The paper studies the effect of
louver angle and louver pitch geometrical parameters, on overall
thermal hydraulic performances of louvered fins.
The comparison between CFD simulations and experimental data
show that established 3-D CFD model gives a good agreement. The
validation agrees, with about 7% of deviation respectively of friction
and Colburn factors to experimental results. As first, it is found that
the louver angle has a strong influence on the heat transfer rate. Then,
louver angle and louver pitch variation of the louvers and their effects
on thermal hydraulic performances are studied. In addition to this
study, it is shown that the second half of the fin takes has a
significant contribution on pressure drop increase without any
increase in heat transfer.
Abstract: A transient finite element model has been developed
to study the heat transfer and fluid flow during spot Gas Tungsten
Arc Welding (GTAW) on stainless steel. Temperature field, fluid
velocity and electromagnetic fields are computed inside the cathode,
arc-plasma and anode using a unified MHD formulation. The
developed model is then used to study the influence of different
helium-argon gas mixtures on both the energy transferred to the
workpiece and the time evolution of the weld pool dimensions. It is
found that the addition of helium to argon increases the heat flux
density on the weld axis by a factor that can reach 6.5. This induces
an increase in the weld pool depth by a factor of 3. It is also found
that the addition of only 10% of argon to helium decreases
considerably the weld pool depth, which is due to the electrical
conductivity of the mixture that increases significantly when argon is
added to helium.
Abstract: Cooktop burners are widely used nowadays. In
cooktop burner design, nozzle efficiency and greenhouse
gas(GHG) emissions mainly depend on heat transfer from the
premixed flame to the impinging surface. This is a complicated
issue depending on the individual and combined effects of various
input combustion variables. Optimal operating conditions for
sustainable burner design were rarely addressed, especially in the
case of multiple slot-jet burners. Through evaluating the optimal
combination of combustion conditions for a premixed slot-jet
array, this paper develops a practical approach for the sustainable
design of gas cooktop burners. Efficiency, CO and NOx emissions
in respect of an array of slot jets using premixed flames were
analysed. Response surface experimental design were applied to
three controllable factors of the combustion process, viz.
Reynolds number, equivalence ratio and jet-to-vessel distance.
Desirability Function Approach(DFA) is the analytic technique
used for the simultaneous optimization of the efficiency and
emission responses.
Abstract: A numerical study is presented on convective heat transfer in enclosures. The results are addressed to automotive headlights containing new-age light sources like Light Emitting Diodes (LED). The heat transfer from the heat source (LED) to the enclosure walls is investigated for mixed convection as interaction of the forced convection flow from an inlet and an outlet port and the natural convection at the heat source. Unlike existing studies, inlet and outlet port are thermally coupled and do not serve to remove hot fluid. The input power of the heat source is expressed by the Rayleigh number. The internal position of the heat source, the aspect ratio of the enclosure, and the inclination angle of one wall are varied. The results are given in terms of the global Nusselt number and the enclosure Nusselt number that characterize the heat transfer from the source and from the interior fluid to the enclosure walls, respectively. It is found that the heat transfer from the source to the fluid can be maximized if the source is placed in the main stream from the inlet to the outlet port. In this case, the Reynolds number and heat source position have the major impact on the heat transfer. A disadvantageous position has been found where natural and forced convection compete each other. The overall heat transfer from the source to the wall increases with increasing Reynolds number as well as with increasing aspect ratio and decreasing inclination angle. The heat transfer from the interior fluid to the enclosure wall increases upon decreasing the aspect ratio and increasing the inclination angle. This counteracting behaviour is caused by the variation of the area of the enclosure wall. All mixed convection results are compared to the natural convection limit.
Abstract: A conjugate heat transfer for steady two-dimensional
mixed convection with magnetic hydrodynamic (MHD) flow of an
incompressible quiescent fluid over an unsteady thermal forming
stretching sheet has been studied. A parameter, M, which is used to
represent the dominance of the magnetic effect has been presented in
governing equations. The similar transformation and an implicit
finite-difference method have been used to analyze the present
problem. The numerical solutions of the flow velocity distributions,
temperature profiles, the wall unknown values of f''(0) and '(θ (0) for
calculating the heat transfer of the similar boundary-layer flow are
carried out as functions of the unsteadiness parameter (S), the Prandtl
number (Pr), the space-dependent parameter (A) and
temperature-dependent parameter (B) for heat source/sink and the
magnetic parameter (M). The effects of these parameters have also
discussed. At the results, it will produce greater heat transfer effect
with a larger Pr and M, S, A, B will reduce heat transfer effects. At
last, conjugate heat transfer for the free convection with a larger G has
a good heat transfer effect better than a smaller G=0.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: The present work demonstrates the design and simulation of a fuzzy control of an air conditioning system at different pressures. The first order Sugeno fuzzy inference system is utilized to model the system and create the controller. In addition, an estimation of the heat transfer rate and water mass flow rate injection into or withdraw from the air conditioning system is determined by the fuzzy IF-THEN rules. The approach starts by generating the input/output data. Then, the subtractive clustering algorithm along with least square estimation (LSE) generates the fuzzy rules that describe the relationship between input/output data. The fuzzy rules are tuned by Adaptive Neuro-Fuzzy Inference System (ANFIS). The results show that when the pressure increases the amount of water flow rate and heat transfer rate decrease within the lower ranges of inlet dry bulb temperatures. On the other hand, and as pressure increases the amount of water flow rate and heat transfer rate increases within the higher ranges of inlet dry bulb temperatures. The inflection in the pressure effect trend occurs at lower temperatures as the inlet air humidity increases.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: Computational fluid dynamics (CFD) simulations
carried out in this paper show that spacer orientation has a major
influence on temperature patterns and on the heat transfer rates. The
local heat flux values significantly vary from high to very low values
at each filament when spacer touches the membrane surface. The
heat flux profile is more uniform when spacer filaments are not in
contact with the membrane thus making this arrangement more
beneficial. The temperature polarization is also found to be less in
this case when compared to the empty channel.
Abstract: In this paper, we present a framework to determine Haar solutions of Bratu-type equations that are widely applicable in fuel ignition of the combustion theory and heat transfer. The method is proposed by applying Haar series for the highest derivatives and integrate the series. Several examples are given to confirm the efficiency and the accuracy of the proposed algorithm. The results show that the proposed way is quite reasonable when compared to exact solution.
Abstract: Impinging jets are widely used in industrial cooling
systems for their high heat transfer characteristics at stagnation points.
However, the heat transfer characteristics are low in the downstream
direction. In order to improve the heat transfer coefficient further
downstream, investigations introducing ribs on jet-cooled flat plates
have been conducted. Most studies regarding the heat-transfer
enhancement using a rib-roughened wall have dealt with the rib pitch.
In this paper, we focused on the rib spacing and demonstrated that the
rib spacing must be more than 6 times the nozzle width to improve heat
transfer at Reynolds number Re=5.0×103 because it is necessary to
have enough space to allow reattachment of flow behind the first rib.
Abstract: The present paper considers the steady free
convection boundary layer flow of a viscoelastics fluid with constant
temperature in the presence of heat generation. The boundary layer
equations are an order higher than those for the Newtonian (viscous)
fluid and the adherence boundary conditions are insufficient to
determine the solution of these equations completely. The governing
boundary layer equations are first transformed into non-dimensional
form by using special dimensionless group. Computations are
performed numerically by using Keller-box method by augmenting
an extra boundary condition at infinity and the results are displayed
graphically to illustrate the influence of viscoelastic K, heat
generation γ , and Prandtl Number, Pr parameters on the velocity
and temperature profiles. The results of the surface shear stress in
terms of the local skin friction and the surface rate of heat transfer in
terms of the local Nusselt number for a selection of the heat
generation parameterγ (=0.0, 0.2, 0.5, 0.8, 1.0) are obtained and
presented in both tabular and graphical formats. Without effect of the
internal heat generation inside the fluid domain for which we take
γ = 0.0, the present numerical results show an excellent agreement
with previous publication.