Abstract: This study presents the improvement of thermal
performance of heat pipe using copper nanofluid with aqueous
solution of n-Butanol. The nanofluids kept in the suspension of
conventional fluids have the potential of superior heat transfer
capability than the conventional fluids due to their improved thermal
conductivity. In this work, the copper nanofluid which has a 40 nm
size with a concentration of 100 mg/lit is kept in the suspension of
the de-ionized (DI) water and an aqueous solution of n-Butanol and
these fluids are used as a working medium in the heat pipe. The study
discusses about the effect of heat pipe inclination, type of working
fluid and heat input on the thermal efficiency and thermal resistance.
The experimental results are evaluated in terms of its performance
metrics and are compared with that of DI water.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.
Abstract: Cutting fluids, usually in the form of a liquid, are
applied to the chip formation zone in order to improve the cutting
conditions. Cutting fluid can be expensive and represents a biological
and environmental hazard that requires proper recycling and
disposal, thus adding to the cost of the machining operation. For
these reasons dry cutting or dry machining has become an
increasingly important approach; in dry machining no coolant or
lubricant is used. This paper discussed the effect of the dry cutting on
cutting force and tool life when machining aerospace materials
(Haynes 242) with using two different coated carbide cutting tools
(TiAlN and TiN/MT-TiCN/TiN). Response surface method (RSM)
was used to minimize the number of experiments. ParTiAlN Swarm
Optimisation (PSO) models were developed to optimize the
machining parameters (cutting speed, federate and axial depth) and
obtain the optimum cutting force and tool life. It observed that
carbide cutting tool coated with TiAlN performed better in dry
cutting compared with TiN/MT-TiCN/TiN. On other hand, TiAlN
performed more superior with using of 100 % water soluble coolant.
Due to the high temperature produced by aerospace materials, the
cutting tool still required lubricant to sustain the heat transfer from
the workpiece.
Abstract: Steady state experiments have been conducted for
natural and mixed convection heat transfer, from five different sized
protruding discrete heat sources, placed at the bottom position on a
PCB and mounted on a vertical channel. The characteristic length (
Lh ) of heat sources vary from 0.005 to 0.011 m. The study has been
done for different range of Reynolds number and modified Grashof
number. From the experiment, the surface temperature distribution
and the Nusselt number of discrete heat sources have been obtained
and the effects of Reynold number and Richardson number on them
have been discussed. The objective is to find the rate of heat
dissipation from heat sources, by placing them at the bottom position
on a PCB and to compare both modes of cooling of heat sources.
Abstract: Turbulent heat transfer to fluid flow through channel with triangular ribs of different angles are presented in this paper. Ansys 14 ICEM and Ansys 14 Fluent are used for meshing process and solving Navier stokes equations respectively. In this investigation three angles of triangular ribs with the range of Reynolds number varied from 20000 to 60000 at constant surface temperature are considered. The results show that the Nusselt number increases with the increase of Reynolds number for all cases at constant surface temperature. According to the profile of local Nusselt number on ribs walled of channel, the peak is at the midpoint between the two ribs. The maximum value of average Nusselt number is obtained for triangular ribs of angel 60°and at Reynolds number of 60000 compared to the Nusselt number for the ribs of angel 90° and 45° and at same Reynolds number. The recirculation regions generated by the ribs corresponding to the velocity streamline show the largest recirculation region at triangular ribs of angle 60° which also provides the highest enhancement of heat transfer.
Abstract: There are extensive applications of lithium
bromide-water absorption chillers in industry, but the heat exchangers
corrosion and refrigerating capacity loss are very difficult to be solved.
In this paper, an experiment was conducted by using plastic heat
transfer tubes instead of copper tubes. As an example, for a lithium
bromide-water absorption chiller of refrigerating capacity of 35kW,
the correlative performance of the lithium bromide-water absorption
chiller using plastic heat transfer tubes was compared with the
traditional lithium bromide-water absorption chiller. And then the
following three aspects, i.e., heat transfer area, pipe resistance, and
safety strength, are analyzed. The results show that plastic heat
transfer tubes can be used on lithium bromide-water absorption
chillers, and its prospect is very optimistic.
Abstract: Unsteady natural convection and heat transfer in a square cavity partially filled with porous media using a thermal
non-equilibrium model is studied in this paper. The left vertical wall is
maintained at a constant hot temperature Th and the right vertical wall
is maintained at a constant cold temperature Tc, while the horizontal
walls are adiabatic. The governing equations are obtained by applying
the Darcy model and Boussinesq approximation. COMSOL’s finite
element method is used to solve the non-dimensional governing
equations together with specified boundary conditions. The governing
parameters of this study are the Rayleigh number (Ra = 10^5, and Ra = 10^6 ), Darcy namber (Da = 10^−2, and Da = 10^−3),
the modified thermal conductivity ratio (10^−1 ≤ γ ≤ 10^4), the inter-phase heat transfer coefficien (10^−1 ≤ H ≤ 10^3) and the
time dependent (0.001 ≤ τ ≤ 0.2). The results presented for
values of the governing parameters in terms of streamlines in both
fluid/porous-layer, isotherms of fluid in fluid/porous-layer, isotherms
of solid in porous layer, and average Nusselt number.
Abstract: In order to obtain an accurate result of the heat transfer
of the rib in the internal cooling Rectangular channel, using separation
of variables, analytical solutions of three dimensional steady-state heat
conduction in rectangular ribs are given by solving three dimensional
steady-state function of the rectangular ribs. Therefore, we can get
solution of three dimensional temperature field in the rib. Based on the
solution, we can get how the Bi number affected on heat transfer.
Furthermore, comparisons of the analytical and numerical results
indicate agreement on temperature field in the rib.
Abstract: Saturated two-phase fluid flows are often subject to
pressure induced oscillations. Due to compressibility the vapor
bubbles act as a spring with an asymmetric non-linear characteristic.
The volume of the vapor bubbles increases or decreases differently if
the pressure fluctuations are compressing or expanding;
consequently, compressing pressure fluctuations in a two-phase pipe
flow cause less displacement in the direction of the pipe flow than
expanding pressure fluctuations. The displacement depends on the
ratio of liquid to vapor, the ratio of pressure fluctuations over average
pressure and on the exciting frequency of the pressure fluctuations.
In addition, pressure fluctuations in saturated vapor bubbles cause
condensation and evaporation within the bubbles and change
periodically the ratio between liquid to vapor, and influence the
dynamical parameters for the oscillation. The oscillations are
conforming to an isenthalpic process at constant enthalpy with no
heat transfer and no exchange of work.
The paper describes the governing non-linear equation for twophase
fluid oscillations with condensation and evaporation, and
presents steady state approximate solutions for free and for pressure
induced oscillations. Resonance criteria and stability are discussed.
Abstract: Evaporator is an important and widely used heat
exchanger in air conditioning and refrigeration industries. Different
methods have been used by investigators to increase the heat transfer
rates in evaporators. One of the passive techniques to enhance heat
transfer coefficient is the application of microfin tubes. The
mechanism of heat transfer augmentation in microfin tubes is
dependent on the flow regime of two-phase flow. Therefore many
investigations of the flow patterns for in-tube evaporation have been
reported in literatures. The gravitational force, surface tension and
the vapor-liquid interfacial shear stress are known as three dominant
factors controlling the vapor and liquid distribution inside the tube. A
review of the existing literature reveals that the previous
investigations were concerned with the two-phase flow pattern for
flow boiling in horizontal tubes [12], [9]. Therefore, the objective of
the present investigation is to obtain information about the two-phase
flow patterns for evaporation of R-134a inside horizontal smooth and
microfin tubes. Also Investigation of heat transfer during flow
boiling of R-134a inside horizontal microfin and smooth tube have
been carried out experimentally The heat transfer coefficients for
annular flow in the smooth tube is shown to agree well with Gungor
and Winterton-s correlation [4]. All the flow patterns occurred in the
test can be divided into three dominant regimes, i.e., stratified-wavy
flow, wavy-annular flow and annular flow. Experimental data are
plotted in two kinds of flow maps, i.e., Weber number for the vapor
versus weber number for the liquid flow map and mass flux versus
vapor quality flow map. The transition from wavy-annular flow to
annular or stratified-wavy flow is identified in the flow maps.
Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: A new analytical model is developed which provides
close-formed solutions for both transient indoor and envelope
temperature changes in buildings. Time-dependent boundary
temperature is presented as Fourier series which can approximate real
weather conditions. The final close-formed solutions are simple,
concise, and comprehensive. The model was compared with
numerical results and good accuracy was obtained. The model can
be used as design and control guidelines in engineering applications
for analysing mechanical heat transfer properties for buildings.
Abstract: The objective of the present work is to conduct
investigations leading to a more complete explanation of single phase
natural convective heat transfer in an enclosure with fin utilizing
nano fluids. The nano fluid used, which is composed of Aluminum
oxide nano particles in suspension of Ethylene glycol, is provided at
various volume fractions. The study is carried out numerically for a
range of Rayleigh numbers, fin heights and aspect ratio. The flow and
temperature distributions are taken to be two-dimensional. Regions
with the same velocity and temperature distributions are identified as
symmetry of sections. One half of such a rectangular region is chosen
as the computational domain taking into account the symmetry about
the fin. Transport equations are modeled by a stream functionvorticity
formulation and are solved numerically by finite-difference
schemes. Comparisons with previously published works on the basis
of special cases are done. Results are presented in the form of
streamline, vector and isotherm plots as well as the variation of local
Nusselt number along the fin under different conditions.
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: The reliable results of an insulated oval duct
considering heat radiation are obtained basing on accurate oval
perimeter obtained by integral method as well as one-dimensional
Plane Wedge Thermal Resistance (PWTR) model. This is an extension
study of former paper of insulated oval duct neglecting heat radiation.
It is found that in the practical situations with long-short-axes ratio a/b
4.5% while t/R2
Abstract: For fire safety purposes, the fire resistance and the
structural behavior of reinforced concrete members are assessed to
satisfy specific fire performance criteria. The available prescribed
provisions are based on standard fire load. Under various fire
scenarios, engineers are in need of both heat transfer analysis and
structural analysis. For heat transfer analysis, the study proposed a
modified finite difference method to evaluate the temperature profile
within a cross section. The research conducted is limited to concrete
sections exposed to a fire on their one side. The method is based on
the energy conservation principle and a pre-determined power
function of the temperature profile. The power value of 2.7 is found
to be a suitable value for concrete sections. The temperature profiles
of the proposed method are only slightly deviate from those of the
experiment, the FEM and the FDM for various fire loads such as
ASTM E 119, ASTM 1529, BS EN 1991-1-2 and 550 oC. The
proposed method is useful to avoid incontinence of the large matrix
system of the typical finite difference method to solve the
temperature profile. Furthermore, design engineers can simply apply
the proposed method in regular spreadsheet software.
Abstract: The flow and heat transfer mechanism in convex
corrugated tubes have been investigated through numerical
simulations in this paper. Two kinds of tube types named as symmetric
corrugated tube (SCT) and asymmetric corrugated tube (ACT) are
modeled and studied numerically based on the RST model. The
predictive capability of RST model is examined in the corrugation wall
in order to check the reliability of RST model under the corrugation
wall condition. We propose a comparison between the RST modelling
the corrugation wall with existing direct numerical simulation of Maaß
C and Schumann U [14]. The numerical results pressure coefficient at
different profiles between RST and DNS are well matched. The
influences of large corrugation tough radii to heat transfer and flow
characteristic had been considered. Flow and heat transfer comparison
between SCT and ACT had been discussed. The numerical results
show that ACT exhibits higher overall heat transfer performance than
SCT.
Abstract: This paper analyses the unsteady, two-dimensional
stagnation point flow of an incompressible viscous fluid over a flat
sheet when the flow is started impulsively from rest and at the same
time, the sheet is suddenly stretched in its own plane with a velocity
proportional to the distance from the stagnation point. The partial
differential equations governing the laminar boundary layer forced
convection flow are non-dimensionalised using semi-similar
transformations and then solved numerically using an implicit finitedifference
scheme known as the Keller-box method. Results
pertaining to the flow and heat transfer characteristics are computed
for all dimensionless time, uniformly valid in the whole spatial region
without any numerical difficulties. Analytical solutions are also
obtained for both small and large times, respectively representing the
initial unsteady and final steady state flow and heat transfer.
Numerical results indicate that the velocity ratio parameter is found
to have a significant effect on skin friction and heat transfer rate at
the surface. Furthermore, it is exposed that there is a smooth
transition from the initial unsteady state flow (small time solution) to
the final steady state (large time solution).
Abstract: Determination of wellbore problems during a
production/injection process might be evaluated thorough
temperature log analysis. Other applications of this kind of log
analysis may also include evaluation of fluid distribution analysis
along the wellbore and identification of anomalies encountered
during production/injection process. While the accuracy of such
prediction is paramount, the common method of determination of a
wellbore temperature log includes use of steady-state energy balance
equations, which hardly describe the real conditions as observed in
typical oil and gas flowing wells during production operation; and
thus increase level of uncertainties. In this study, a practical method
has been proposed through development of a simplified semianalytical
model to apply for predicting temperature profile along the
wellbore. The developed model includes an overall heat transfer
coefficient accounting all modes of heat transferring mechanism,
which has been focused on the prediction of a temperature profile as
a function of depth for the injection/production wells. The model has
been validated with the results obtained from numerical simulation.
Abstract: Various solar energy technologies exist and they have
different application techniques in the generation of electrical power.
The widespread use of photovoltaic (PV) modules in such
technologies has been limited by relatively high costs and low
efficiencies. The efficiency of PV panels decreases as the operating
temperatures increase. This is due to the affect of solar intensity and
ambient temperature. In this work, Computational Fluid Dynamics
(CFD) was used to model the heat transfer from a standard PV panel
and thus determine the rate of dissipation of heat. To accurately
model the specific climatic conditions of the United Arab Emirates
(UAE), a case study of a new build green building in Dubai was
used. A finned heat pipe arrangement is proposed and analyzed to
determine the improved heat dissipation and thus improved
performance efficiency of the PV panel. A prototype of the
arrangement is built for experimental testing to validate the CFD
modeling and proof of concept.