Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: Copper based composites reinforced with WC and Ti
particles were prepared using planetary ball-mill. The experiment
was designed by using Taguchi technique and milling was carried out
in an air for several hours. The powder was characterized before and
after milling using the SEM, TEM and X-ray for microstructure and
for possible new phases. Microstructures show that milled particles
size and reduction in particle size depend on many parameters. The
distance d between planes of atoms estimated from X-ray powder
diffraction data and TEM image. X-ray diffraction patterns of the
milled powder did not show clearly any new peak or energy shift, but
the TEM images show a significant change in crystalline structure of
corporate on titanium in the composites.
Abstract: The steady mixed convection boundary layer flow from
a vertical cone in a porous medium filled with a nanofluid is
numerically investigated using different types of nanoparticles as Cu
(copper), Al2O3 (alumina) and TiO2 (titania). The boundary value
problem is solved by using the shooting technique by reducing it
into an ordinary differential equation. Results of interest for the local
Nusselt number with various values of the constant mixed convection
parameter and nanoparticle volume fraction parameter are evaluated.
It is found that dual solutions exist for a certain range of mixed
convection parameter.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: Thyroid dysfunction is one of the most frequently
reported complications of chronic blood transfusion therapy in patients with beta-thalassemia major (BTM). However, the occurrence of thyroid dysfunction and its possible association with
iron overload in BTM patients is still under debate. Therefore, this
study aimed to investigate the status of thyroid functions and iron overload in adolescent and young adult patients with BTM in Jordan population. Thirty six BTM patients aged 12-28 years and matched controls were included in this study. All patients have been receiving frequent blood transfusion to maintain pretransfusion hemoglobin
concentration above 10 g dl-1 and deferoxamine at a dose of 45 mg kg-1 day-1 (8 h, 5-7 days/week) by subcutaneous infusion. Blood
samples were drawn from patients and controls. The status of thyroid functions and iron overload was evaluated by measurements of serum
free thyroxine (FT4), triiodothyronine (FT3), thyrotropin (TSH) and
serum ferritin level. A number of some hematological and
biochemical parameters were also measured. It was found that hematocrit, serum ferritin, hemoglobin, FT3 and zinc, copper mean values were significantly higher in the patients than in the controls (P< 0.05). On other hand, leukocyte, FT4 and TSH mean values were
similar to that of the controls. In addition, our data also indicated that
all of the above examined parameters were not significantly affected
by the patient-s age and gender. Deferoxamine approach for removing excess iron from our BTM patient did not normalize the
values of serum ferritin, copper and zinc, suggesting poor compliance
with deferoxamine chelation therapy. Thus, we recommend the use
of a combination of deferoxamine and deferiprone to reduce the risk
of excess of iron in our patients. Furthermore, thyroid dysfunction
appears to be a rare complication, because our patients showed
normal mean levels for serum TSH and FT4. However, high mean
levels of serum ferritin, zinc, copper might be seen as potential risk
factors for initiation and development of thyroid dysfunctions and
other diseases. Therefore, further studies must be carried out at
yearly intervals with large sample number, to detect subclinical
thyroid dysfunction cases.
Abstract: Nanowire arrays of copper with uniform diameters have
been synthesized by potentiostatic electrochemical metal deposition
(EMD) of copper sulphate and potassium chloride solution within
the nano-channels of porous Indium-Tin Oxide (ITO), also known as
Tin doped Indium Oxide templates. The nanowires developed were
fairly continuous with diameters ranging from 110-140 nm along
the entire length. Single as well as poly-crystalline copper wires
have been prepared by application of appropriate potential during the
EMD process. Scanning electron microscopy (SEM), high resolution
transmission electron microscopy (HRTEM), small angle electron
diffraction (SAED) and atomic force microscopy (AFM) were used
to characterize the synthesized nano wires at room temperature. The
electrochemical response of synthesized products was evaluated by
cyclic voltammetry while surface energy analysis was carried out
using a Goniometer.
Abstract: The copper flotation tailings from Konkola Copper
mine in Nchanga, Zambia were used in the study. The purpose of this
study was to determine the leaching characteristics of the tailings
material prior and after the physical beneficiation process is
employed. The Knelson gravity concentrator (KC-MD3) was used for
the beneficiation process. The copper leaching efficiencies and
impurity co-extraction percentages in both the upgraded and the raw
feed material were determined at different pH levels and temperature.
It was observed that the copper extraction increased with an increase
in temperature and a decrease in pH levels. In comparison to the raw
feed sample, the upgraded sample reported a maximum copper
extraction of 69% which was 9%, higher than raw feed % extractions.
The impurity carry over was reduced from 18% to 4 % on the
upgraded sample. The reduction in impurity co-extraction was as a
result of the removal of the reactive gangue elements during the
upgrading process, this minimized the number of side reaction
occurring during leaching.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: In this paper, the innovative intelligent fuzzy weighted
input estimation method (FWIEM) can be applied to the inverse heat
transfer conduction problem (IHCP) to estimate the unknown
time-varying heat flux efficiently as presented. The feasibility of this
method can be verified by adopting the temperature measurement
experiment. We would like to focus attention on the heat flux
estimation to three kinds of samples (Copper, Iron and Steel/AISI 304)
with the same 3mm thickness. The temperature measurements are then
regarded as the inputs into the FWIEM to estimate the heat flux. The
experiment results show that the proposed algorithm can estimate the
unknown time-varying heat flux on-line.
Abstract: Lattice Monte Carlo methods are an excellent
choice for the simulation of non-linear thermal diffusion
problems. In this paper, and for the first time, Lattice Monte
Carlo analysis is performed on thermal diffusion combined
with convective heat transfer. Laminar flow of water modeled
as an incompressible fluid inside a copper pipe with a constant
surface temperature is considered. For the simulation of
thermal conduction, the temperature dependence of the
thermal conductivity of the water is accounted for. Using the
novel Lattice Monte Carlo approach, temperature distributions
and energy fluxes are obtained.
Abstract: The present paper is an experimental investigation of
roughness effects on nucleate pool boiling of refrigerant R113 on
horizontal circular copper surfaces. The copper samples were treated
by different sand paper grit sizes to achieve different surface
roughness. The average surface roughness of the four samples was
0.901, 0.735, 0.65, and 0.09, respectively. The experiments were
performed in the heat flux range of 8 to 200kW/m2. The heat transfer
coefficient was calculated by measuring wall superheat of the
samples and the input heat flux. The results show significant
improvement of heat transfer coefficient as the surface roughness is
increased. It is found that the heat transfer coefficient of the sample
with Ra=0.901 is 3.4, 10.5, and 38.5% higher in comparison with
surfaces with Ra of 0.735, 0.65, and 0.09 at heat flux of 170 kW/m2.
Moreover, the results are compared with literature data and the well
known Cooper correlation.
Abstract: This study was carried out to develop a flotation
procedure for an oxide copper ore from a Region in Central Africa
for producing an 18% copper concentrate for downstream processing
at maximum recovery from a 4% copper feed grade. The copper
recoveries achieved from the test work were less than 50% despite
changes in reagent conditions (multistage sulphidisation, use of RCA
emulsion and mixture, use of AM 2, etc). The poor recoveries were
attributed to the mineralogy of the ore from which copper silicates
accounted for approximately 70% (mass) of the copper minerals in
the ore. These can be complex and difficult to float using
conventional flotation methods. Best results were obtained using
basic sulphidisation procedures, a high flotation temperature and
extended flotation residence time.
Abstract: An investigation of noise in a micro stepping motor is
considered to study in this article. Because of the trend towards higher
precision and more and more small 3C (including Computer,
Communication and Consumer Electronics) products, the micro
stepping motor is frequently used to drive the micro system or the
other 3C products. Unfortunately, noise in a micro stepped motor is
too large to accept by the customs. To depress the noise of a micro
stepped motor, the dynamic characteristics in this system must be
studied. In this article, a Visual Basic (VB) computer program speed
controlled micro stepped motor in a digital camera is investigated.
Karman KD2300-2S non-contract eddy current displacement sensor,
probe microphone, and HP 35670A analyzer are employed to analyze
the dynamic characteristics of vibration and noise in a motor. The
vibration and noise measurement of different type of bearings and
different treatment of coils are compared. The rotating components,
bearings, coil, etc. of the motor play the important roles in producing
vibration and noise. It is found that the noise will be depressed about
3~4 dB and 6~7 dB, when substitutes the copper bearing with plastic
one and coats the motor coil with paraffin wax, respectively.
Abstract: This study investigated the removal efficiency of electrokinetic remediation of copper-contaminated soil at different combinations of enhancement reagents used as anolyte and catholyte. Sodium hydroxide (at 0.1, 0.5, and 1.0 M concentrations) and distilled water were used as anolyte, while lactic acid (at 0.01, 0.1, and 0.5 M concentrations), ammonium citrate (also at 0.01, 0.1, and 0.5 M concentrations) and distilled water were used as catholyte. A continuous voltage application (1.0 VDC/cm) was employed for 240 hours for each experiment. The copper content of the catholyte was determined at the end of the 240-hour period. Optimization was carried out with a Response Surface Methodology - Optimal Design, including F test, and multiple comparison method, to determine which pair of anolyte-catholyte was the most significant for the removal efficiency. "1.0 M NaOH" was found to be the most significant anolyte while it was established that lactic acid was the most significant type of catholyte to be used for the most successful electrokinetic experiments. Concentrations of lactic acid should be at the range of 0.1 M to 0.5 M to achieve maximum percent removal values.
Abstract: Khatunabad area is situated geologically in Urmieh-
Dokhtar magmatic belt in NW of Iran. In this research, studied area
has been investigated in order to recognize the potential copper and
molybdenum-bearing target areas. The survey layers include the
lithologic units, alteration, geochemical result, tectonics and copper
and molybdenum occurrence. As an accurate decision can have a
considerable effect on exploration plans, so in this efforts have been
made to make use of new combination method. For this purpose, the
analytical hierarchy process was used and revealed highly potential
copper and molybdenum mineralization areas. Based on achieved
results, geological perspective in north of studied area is appropriate
for advance stage, especially for subsurface exploration in future.
Abstract: In this study, the effect of L-arginine was examined at the neuromuscular junction of the chick biventer cervicis muscle. LArginine at 500 μg/ ml, decreased twitch response to electerical stimulation, and produced rightward shift of the dose- response curve for acetylcholine or carbachol. L-Arginine at 1000μg/ ml produced a strong shift to the right of the dose – response curve for acetylcholine or carbachol with a reduction in the efficacy. The inhibitory effect of L-arginine on the twitch response was blocked by caffeine (200μg/ ml). NO levels were also measured in the chick biventer cervicis muscle homogenates, using spectrophotometric method for the direct detection of NO, nitrite and nitrate. Total nitrite (nitrite + nitrate) was measured by a spectrophotometer at 540 nm after the conversion of nitrate to nitrite by copperized cadmium granules. NO levels were found to be significantly increased in concentrations 500 and 1000μg/ ml of L-arginine in comparison with the control group (p
Abstract: The expansion mechanism of a partially ionized plasma produced by laser interaction with solid target (copper) is studied. For this purpose we use a hydrodynamical model which includes a source term combined with Saha's equation. The obtained self-similar solution in the limit of quasi-neutrality shows that the expansion, at the earlier stage, is driven by the combination of thermal pressure and electrostatic potential. They are of the same magnitude. The initial ionized fraction and the temperature are the leading parameters of the expanding profiles,
Abstract: An experimental study is realized in order to verify the
Mini Heat Pipe (MHP) concept for cooling high power dissipation
electronic components and determines the potential advantages of
constructing mini channels as an integrated part of a flat heat pipe. A
Flat Mini Heat Pipe (FMHP) prototype including a capillary structure
composed of parallel rectangular microchannels is manufactured and
a filling apparatus is developed in order to charge the FMHP. The
heat transfer improvement obtained by comparing the heat pipe
thermal resistance to the heat conduction thermal resistance of a
copper plate having the same dimensions as the tested FMHP is
demonstrated for different heat input flux rates. Moreover, the heat
transfer in the evaporator and condenser sections are analyzed, and
heat transfer laws are proposed. In the theoretical part of this work, a
detailed mathematical model of a FMHP with axial microchannels is
developed in which the fluid flow is considered along with the heat
and mass transfer processes during evaporation and condensation.
The model is based on the equations for the mass, momentum and
energy conservation, which are written for the evaporator, adiabatic,
and condenser zones. The model, which permits to simulate several
shapes of microchannels, can predict the maximum heat transfer
capacity of FMHP, the optimal fluid mass, and the flow and thermal
parameters along the FMHP. The comparison between experimental
and model results shows the good ability of the numerical model to
predict the axial temperature distribution along the FMHP.
Abstract: The Mahin area is a part of Tarom- Hashtjin zone that
located in west of Qazvin province in northwest of Iran. Many copper
and base metals ore deposits are hosted by this zone. High potential
localities identification in this area is very necessary. The objective of
this research, is finding hydrothermal alteration zones by remote
sensing methods and best processing technique of Advanced
Spaceborne Thermal Emission and Reflection Radiometer (ASTER)
data. Different methods such as band ratio, Principal Component
Analysis (PCA), Minimum Noise Fraction (MNF) and Least Square
Fit (LS-Fit) were used for mapping hydrothermal alteration zones.
Abstract: In the paper the results of calculations of the dynamic
response of a multi-storey reinforced concrete building to a strong
mining shock originated from the main region of mining activity in
Poland (i.e. the Legnica-Glogow Copper District) are presented. The
representative time histories of accelerations registered in three
directions were used as ground motion data in calculations of the
dynamic response of the structure. Two variants of a numerical model
were applied: the model including only structural elements of the
building and the model including both structural and non-structural
elements (i.e. partition walls and ventilation ducts made of brick). It
turned out that non-structural elements of multi-storey RC buildings
have a small impact of about 10 % on natural frequencies of these
structures. It was also proved that the dynamic response of building
to mining shock obtained in case of inclusion of all non-structural
elements in the numerical model is about 20 % smaller than in case
of consideration of structural elements only. The principal stresses
obtained in calculations of dynamic response of multi-storey building
to strong mining shock are situated on the level of about 30% of
values obtained from static analysis (dead load).