Abstract: A cell-centered finite volume scheme for discretizing diffusion operators on distorted quadrilateral meshes has recently been designed and added to APMFCG to enable that code to be used as a tool for studying explosive magnetic flux compression generators. This paper describes this scheme. Comparisons with analytic results for 2-D test cases are presented, as well as 2-D results from a test of a "realistic" generator configuration.
Abstract: Fully customized hardware based technology provides high performance and low power consumption by specializing the tasks in hardware but lacks design flexibility since any kind of changes require re-design and re-fabrication. Software based solutions operate with software instructions due to which a great flexibility is achieved from the easy development and maintenance of the software code. But this execution of instructions introduces a high overhead in performance and area consumption. In past few decades the reconfigurable computing domain has been introduced which overcomes the traditional trades-off between flexibility and performance and is able to achieve high performance while maintaining a good flexibility. The dramatic gains in terms of chip performance and design flexibility achieved through the reconfigurable computing systems are greatly dependent on the design of their computational units being integrated with reconfigurable logic resources. The computational unit of any reconfigurable system plays vital role in defining its strength. In this research paper an RFU based computational unit design has been presented using the tightly coupled, multi-threaded reconfigurable cores. The proposed design has been simulated for VLIW based architectures and a high gain in performance has been observed as compared to the conventional computing systems.
Abstract: In this paper multivariable predictive PID controller has
been implemented on a multi-inputs multi-outputs control problem
i.e., quadruple tank system, in comparison with a simple multiloop
PI controller. One of the salient feature of this system is an
adjustable transmission zero which can be adjust to operate in both
minimum and non-minimum phase configuration, through the flow
distribution to upper and lower tanks in quadruple tank system.
Stability and performance analysis has also been carried out for this
highly interactive two input two output system, both in minimum
and non-minimum phases. Simulations of control system revealed
that better performance are obtained in predictive PID design.
Abstract: The epoxidation of soybean oil at temperature of 600C
was provided the best result in terms of attaching the –OH
functionality. Temperatures below and above 600C it is likely the
attaching reaction did not proceed sufficiently fast. The considerable
yield below 40%, implies the oil is not completely converted, it is not
possible by conventional methods, because the epoxide decomposes
at the temperature required. The objective of this work was the
development of catalyst toward the conversion of epoxide and polyol
with reaction temperature at 50,60, and 700C. The effect of different
type of catalyst were studied, the effect of alcohols with different
molecular configuration was determined which leads to selective
addition of alcohols to the epoxide oils.
Abstract: To improve the classification rate of the face
recognition, features combination and a novel non-linear kernel are
proposed. The feature vector concatenates three different radius of
local binary patterns and Gabor wavelet features. Gabor features are
the mean, standard deviation and the skew of each scaling and
orientation parameter. The aim of the new kernel is to incorporate
the power of the kernel methods with the optimal balance between
the features. To verify the effectiveness of the proposed method,
numerous methods are tested by using four datasets, which are
consisting of various emotions, orientations, configuration,
expressions and lighting conditions. Empirical results show the
superiority of the proposed technique when compared to other
methods.
Abstract: This paper proposes a novel solution for optimizing
the size and communication overhead of a distributed multiagent
system without compromising the performance. The proposed approach
addresses the challenges of scalability especially when the
multiagent system is large. A modified spectral clustering technique
is used to partition a large network into logically related clusters.
Agents are assigned to monitor dedicated clusters rather than monitor
each device or node. The proposed scalable multiagent system is
implemented using JADE (Java Agent Development Environment)
for a large power system. The performance of the proposed topologyindependent
decentralized multiagent system and the scalable multiagent
system is compared by comprehensively simulating different
fault scenarios. The time taken for reconfiguration, the overall computational
complexity, and the communication overhead incurred are
computed. The results of these simulations show that the proposed
scalable multiagent system uses fewer agents efficiently, makes faster
decisions to reconfigure when a fault occurs, and incurs significantly
less communication overhead.
Abstract: The cost of damage to the non-structural systems in
critical facilities like nuclear power plants and hospitals can exceed
80% of the total cost of damage during an earthquake. The failure of
nonstructural components, especially, piping systems led to leakage of
water and subsequent shut-down of hospitals immediately after the
event. Consequently, the evaluation of performance of these types of
structural configurations has become necessary to mitigate the risk and
to achieve reliable designs.
This paper focuses on a methodology to evaluate the static and
dynamic characteristics of complex actual piping system based on
NFPA-13 and SMACNA guidelines. The result of this study revealed
that current piping system subjected to design lateral force and design
spectrum based on UBC-97 was failed in both cases and mode shapes
between piping system and building structure were very different
Abstract: In the present research, steam cracking of two types of
feedstocks i.e., naphtha and ethane is simulated for Pyrocrack1-1 and
2/2 coil configurations considering two key parameters of coil outlet
temperature (COT) and coil capacity using a radical based kinetic
model. The computer model is confirmed using the industrial data
obtained from Amirkabir Petrochemical Complex. The results are in
good agreement with performance data for naphtha cracking in a
wide range of severity (0.4-0.7), and for ethane cracking on various
conversions (50-70). It was found that Pyrocrack2-2 coil type is an
appropriate choice for steam cracking of ethane at reasonable
ethylene yield while resulting in much lower tube wall temperature
while Pyrocrack1-1 coil type is a proper selection for liquid
feedstocks i.e. naphtha. It can be used for cracking of liquid
feedstocks at optimal ethylene yield whereas not exceeding the
allowable maximum tube temperature.
Abstract: In this paper, Differential Evolution (DE) algorithm, a new promising evolutionary algorithm, is proposed to train Radial Basis Function (RBF) network related to automatic configuration of network architecture. Classification tasks on data sets: Iris, Wine, New-thyroid, and Glass are conducted to measure the performance of neural networks. Compared with a standard RBF training algorithm in Matlab neural network toolbox, DE achieves more rational architecture for RBF networks. The resulting networks hence obtain strong generalization abilities.
Abstract: The current study describes a multi-objective optimization technique for positioning of houses in a residential neighborhood. The main task is the placement of residential houses in a favorable configuration satisfying a number of objectives. Solving the house layout problem is a challenging task. It requires an iterative approach to satisfy design requirements (e.g. energy efficiency, skyview, daylight, roads network, visual privacy, and clear access to favorite views). These design requirements vary from one project to another based on location and client preferences. In the Gulf region, the most important socio-cultural factor is the visual privacy in indoor space. Hence, most of the residential houses in this region are surrounded by high fences to provide privacy, which has a direct impact on other requirements (e.g. daylight and direction to favorite views). This investigation introduces a novel technique to optimally locate and orient residential buildings to satisfy a set of design requirements. The developed technique explores the search space for possible solutions. This study considers two dimensional house planning problems. However, it can be extended to solve three dimensional cases.
Abstract: Dielectric sheet perturbation to the dominant TE111
mode resonant frequency of a circular cavity is studied and presented
in this paper. The dielectric sheet, placed at the middle of the airfilled
cavity, introduces discontinuities and disturbs the configuration
of electromagnetic fields in the cavity. For fixed dimensions of cavity
and fixed thickness of the loading dielectric, the dominant resonant
frequency varies quite linearly with the permittivity of the dielectric.
This quasi-linear relationship is plotted using Maple software and
verified using 3D electromagnetic simulations. Two probes are used
in the simulation for wave excitation into and from the cavity. The
best length of probe is found to be 3 mm, giving the closest resonant
frequency to the one calculated using Maple. A total of fourteen
different dielectrics of permittivity ranging from 1 to 12.9 are tested
one by one in the simulation. The works show very close agreement
between the results from Maple and the simulation. A constant
difference of 0.04 GHz is found between the resonant frequencies
collected during simulation and the ones from Maple. The success of
this project may lead to the possibility of using the middle loaded
cavity at TE111 mode as a microwave non-destructive testing of solid
materials.
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: Pollution emission levels of aircraft engines are a
nowadays high concern. Any technological advance that could reduce
emission levels is always welcome. In what concerns aircraft engines,
a possible solution for this problem could be the use of regenerators
and intercoolers. These components might reduce the specific fuel
consumption, increase efficiency and specific thrust and consequently
reduce the pollution levels of the engine. This is not a novel solution.
These heat exchangers are already is use in stationary engines. For
aircraft engines, the extra weight of the needed hardware could
overcome the fuel saved. This work compares a conventional engine
with configurations that use intercoolers and regenerators.
Abstract: The use of composite materials in offshore engineering for deep sea oil production riser systems has drawn considerable interest due to the potential weight savings and improvement in durability. The design of composite risers consists of two stages: (1) local design based on critical local load cases, and (2) global analysis of the full length composite riser under global loads and assessment of critical locations. In the first stage, eight different material combinations were selected and their laminate configurations optimised under local load considerations. Stage two includes a final local stress analysis of the critical sections of the riser under the combined loads determined in the global analysis. This paper describes two design methodologies of the composite riser to provide minimum structural weight and shows that the use of off angle fibre orientations in addition to axial and hoop reinforcements offer substantial weight savings and ensure the structural capacity.
Abstract: This work presents the mixed-mode II/III prestressed split-cantilever beam specimen for the fracture testing of composite materials. In accordance with the concept of prestressed composite beams one of the two fracture modes is provided by the prestressed state of the specimen, and the other one is increased up to fracture initiation by using a testing machine. The novel beam-like specimen is able to provide any combination of the mode-II and mode-III energy release rates. A simple closed-form solution is developed using beam theory as a data reduction scheme and for the calculation of the energy release rates in the new configuration. The applicability and the limitations of the novel fracture mechanical test are demonstrated using unidirectional glass/polyester composite specimens. If only crack propagation onset is involved then the mixed-mode beam specimen can be used to obtain the fracture criterion of transparent composite materials in the GII - GIII plane in a relatively simple way.
Abstract: In most of the popular implementation of Parallel GAs
the whole population is divided into a set of subpopulations, each
subpopulation executes GA independently and some individuals are
migrated at fixed intervals on a ring topology. In these studies,
the migrations usually occur 'synchronously' among subpopulations.
Therefore, CPUs are not used efficiently and the communication
do not occur efficiently either. A few studies tried asynchronous
migration but it is hard to implement and setting proper parameter
values is difficult.
The aim of our research is to develop a migration method which is
easy to implement, which is easy to set parameter values, and which
reduces communication traffic. In this paper, we propose a traffic
reduction method for the Asynchronous Parallel Distributed GA by
migration of elites only. This is a Server-Client model. Every client
executes GA on a subpopulation and sends an elite information to the
server. The server manages the elite information of each client and
the migrations occur according to the evolution of sub-population in
a client. This facilitates the reduction in communication traffic.
To evaluate our proposed model, we apply it to many function optimization
problems. We confirm that our proposed method performs
as well as current methods, the communication traffic is less, and
setting of the parameters are much easier.
Abstract: The realization of current-mode quadrature oscillators
using current controlled current conveyor transconductance
amplifiers (CCCCTAs) and grounded capacitors is presented. The
proposed oscillators can provide 2 sinusoidal output currents with 90º
phase difference. It is enabled non-interactive dual-current control for
both the condition of oscillation and the frequency of oscillation.
High output impedances of the configurations enable the circuit to be
cascaded without additional current buffers. The use of only
grounded capacitors is ideal for integration. The circuit performances
are depicted through PSpice simulations, they show good agreement
to theoretical anticipation.
Abstract: The objective of this research is to study the technical
and economic performance of wind/diesel/battery (W/D/B) system
supplying a remote small gathering of six families using HOMER
software package. The electrical energy is to cater for the basic needs
for which the daily load pattern is estimated. Net Present Cost (NPC)
and Cost of Energy (COE) are used as economic criteria, while the measure of performance is % of power shortage. Technical and
economic parameters are defined to estimate the feasibility of the
system under study. Optimum system configurations are estimated for two sites. Using HOMER software, the simulation results showed that W/D/B systems are economical for the assumed community sites
as the price of generated electricity is about 0.308 $/kWh, without
taking external benefits into considerations. W/D/B systems are more
economical than W/B or diesel alone systems, as the COE is 0.86 $/kWh for W/B and 0.357 $/kWh for diesel alone.
Abstract: This paper aims to provide a conceptual framework to examine competitive disadvantage of banks that suffer from poor performance. Banks generate revenues mainly from the interest rate spread on taking deposits and making loans while collecting fees in the process. To maximize firm value, banks seek loan growth and expense control while managing risk associated with loans with respect to non-performing borrowers or narrowing interest spread between assets and liabilities. Competitive disadvantage refers to the failure to access imitable resources and to build managing capabilities to gain sustainable return given appropriate risk management. This paper proposes a four-quadrant framework of organizational typology is subsequently proposed to examine the features of competitive disadvantage in the banking sector. A resource configuration model, which is extracted from CAMEL indicators to examine the underlying features of bank failures.
Abstract: To fight against the economic crisis, French
Government, like many others in Europe, has decided to give a boost
to high-speed line projects. This paper explores the implementation
and decision-making process in TGV projects, their evolutions,
especially since the Mediterranean TGV-line. This project was
probably the most controversial, but paradoxically represents today a
huge success for all the actors involved.
What kind of lessons we can learn from this experience? How to
evaluate the impact of this project on TGV-line planning? How can
we characterize this implementation and decision-making process
regards to the sustainability challenges?
The construction of Mediterranean TGV-line was the occasion to
make several innovations: to introduce more dialog into the decisionmaking
process, to take into account the environment, to introduce a
new project management and technological innovations. That-s why
this project appears today as an example in terms of integration of
sustainable development.
In this paper we examine the different kinds of innovations
developed in this project, by using concepts from sociology of
innovation to understand how these solutions emerged in a
controversial situation. Then we analyze the lessons which were
drawn from this decision-making process (in the immediacy and a
posteriori) and the way in which procedures evolved: creation of new
tools and devices (public consultation, project management...).
Finally we try to highlight the impact of this evolution on TGV
projects governance. In particular, new methods of implementation
and financing involve a reconfiguration of the system of actors. The
aim of this paper is to define the impact of this reconfiguration on
negotiations between stakeholders.