Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetically and thermal stresses remain major failures
for insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: Commercial nanocomposite food packaging type nano-silver containers were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The presence of nanoparticles consistent with the incorporation of 1% nano-silver (Ag) and 0.1% titanium dioxide (TiO2) nanoparticle into polymeric materials formed into food containers was confirmed. Both nanomaterials used in this type of packaging appear to be embedded in a layered configuration within the bulk polymer. The dimensions of the incorporated nanoparticles were investigated using X-ray diffraction (XRD) and determined by calculation using the Scherrer Formula; these were consistent with Ag and TiO2 nanoparticles in the size range 20-70nm both were spherical shape nanoparticles. Antimicrobial assessment of the nanocomposite container has also been performed and the results confirm the antimicrobial activity of Ag and TiO2 nanoparticles in food packaging containers. Migration assessments were performed in a wide range of food matrices to determine the migration of nanoparticles from the packages. The analysis was based upon the relevant European safety Directives and involved the application of inductively coupled plasma mass spectrometry (ICP-MS) to identify the range of migration risk. The data pertain to insignificance levels of migration of Ag and TiO2 nanoparticles into the selected food matrices.
Abstract: In this paper an average number of re-handlings
analysis is proposed to solve the problem of finding bays
configuration in small container terminal in Gliwice, Poland.
Rehandlings in this terminal can be performed only by reachstackers.
The goal of the heuristic is to plan the reachstacter moves in the
terminal, assuming that the target containers are reached and the
number of re-handings is minimized. The real situation requires also
to take into account the model of the problem environment
uncertainty caused by the fact that many containers are not delivered
to the terminal on time, or can not be sent on scheduled time. To
enable this, the heuristic uses some assumptions to simplify problem
analysis.
Abstract: This paper deals with the development and obstacles of
Korean women-s political participation in recent years. Since the year
1948 after the declaration of a modern state, Korea has tried to
establish the democracy but still in the field of women-s political
participation it meets a lot of problems such as women-s political
consciousness, male dominated political culture and institutional
constraints. After the introduction of quota system in the list of
political party, women-s political participation began to change its
configuration. More women candidates have willingly presented at
elections.
Abstract: Both software applications and their development environment are becoming more and more distributed. This trend impacts not only the way software computes, but also how it looks. This article proposes a Human Computer Interface (HCI) template from three representative applications we have developed. These applications include a Multi-Agent System based software, a 3D Internet computer game with distributed game world logic, and a programming language environment used in constructing distributed neural network and its visualizations. HCI concepts that are common to these applications are described in abstract terms in the template. These include off-line presentation of global entities, entities inside a hierarchical namespace, communication and languages, reconfiguration of entity references in a graph, impersonation and access right, etc. We believe the metaphor that underlies an HCI concept as well as the relationships between a bunch of HCI concepts are crucial to the design of software systems and vice versa.
Abstract: Power loss reduction is one of the main targets in power industry and so in this paper, the problem of finding the optimal configuration of a radial distribution system for loss reduction is considered. Optimal reconfiguration involves the selection of the best set of branches to be opened ,one each from each loop, for reducing resistive line losses , and reliving overloads on feeders by shifting the load to adjacent feeders. However ,since there are many candidate switching combinations in the system ,the feeder reconfiguration is a complicated problem. In this paper a new approach is proposed based on a simple optimum loss calculation by determining optimal trees of the given network. From graph theory a distribution network can be represented with a graph that consists a set of nodes and branches. In fact this problem can be viewed as a problem of determining an optimal tree of the graph which simultaneously ensure radial structure of each candidate topology .In this method the refined genetic algorithm is also set up and some improvements of algorithm are made on chromosome coding. In this paper an implementation of the algorithm presented by [7] is applied by modifying in load flow program and a comparison of this method with the proposed method is employed. In [7] an algorithm is proposed that the choice of the switches to be opened is based on simple heuristic rules. This algorithm reduce the number of load flow runs and also reduce the switching combinations to a fewer number and gives the optimum solution. To demonstrate the validity of these methods computer simulations with PSAT and MATLAB programs are carried out on 33-bus test system. The results show that the performance of the proposed method is better than [7] method and also other methods.
Abstract: Network reconfiguration in distribution system is realized by changing the status of sectionalizing switches to reduce the power loss in the system. This paper presents a new method which applies an artificial bee colony algorithm (ABC) for determining the sectionalizing switch to be operated in order to solve the distribution system loss minimization problem. The ABC algorithm is a new population based metaheuristic approach inspired by intelligent foraging behavior of honeybee swarm. The advantage of ABC algorithm is that it does not require external parameters such as cross over rate and mutation rate as in case of genetic algorithm and differential evolution and it is hard to determine these parameters in prior. The other advantage is that the global search ability in the algorithm is implemented by introducing neighborhood source production mechanism which is a similar to mutation process. To demonstrate the validity of the proposed algorithm, computer simulations are carried out on 14, 33, and 119-bus systems and compared with different approaches available in the literature. The proposed method has outperformed the other methods in terms of the quality of solution and computational efficiency.
Abstract: In recent years, scanning probe atomic force
microscopy SPM AFM has gained acceptance over a wide spectrum
of research and science applications. Most fields focuses on physical,
chemical, biological while less attention is devoted to manufacturing
and machining aspects. The purpose of the current study is to assess
the possible implementation of the SPM AFM features and its
NanoScope software in general machining applications with special
attention to the tribological aspects of cutting tool. The surface
morphology of coated and uncoated as-received carbide inserts is
examined, analyzed, and characterized through the determination of
the appropriate scanning setting, the suitable data type imaging
techniques and the most representative data analysis parameters
using the MultiMode SPM AFM in contact mode. The NanoScope
operating software is used to capture realtime three data types
images: “Height", “Deflection" and “Friction". Three scan sizes are
independently performed: 2, 6, and 12 μm with a 2.5 μm vertical
range (Z). Offline mode analysis includes the determination of three
functional topographical parameters: surface “Roughness", power
spectral density “PSD" and “Section". The 12 μm scan size in
association with “Height" imaging is found efficient to capture every
tiny features and tribological aspects of the examined surface. Also,
“Friction" analysis is found to produce a comprehensive explanation
about the lateral characteristics of the scanned surface. Configuration
of many surface defects and drawbacks has been precisely detected
and analyzed.
Abstract: Recently, neural networks have shown good
results for detection of a certain pattern in a given image. In
our previous papers [1-5], a fast algorithm for pattern
detection using neural networks was presented. Such
algorithm was designed based on cross correlation in the
frequency domain between the input image and the weights
of neural networks. Image conversion into symmetric shape
was established so that fast neural networks can give the
same results as conventional neural networks. Another
configuration of symmetry was suggested in [3,4] to improve
the speed up ratio. In this paper, our previous algorithm for
fast neural networks is developed. The frequency domain
cross correlation is modified in order to compensate for the
symmetric condition which is required by the input image.
Two new ideas are introduced to modify the cross correlation
algorithm. Both methods accelerate the speed of the fast
neural networks as there is no need for converting the input
image into symmetric one as previous. Theoretical and
practical results show that both approaches provide faster
speed up ratio than the previous algorithm.
Abstract: The purpose of this work is fast design optimization of
the seal chamber. The study includes the mass transfer between lower
and upper chamber on seal chamber for hot water application pumps.
The use of Fluent 12.1 commercial code made it possible to capture
complex flow with heat-mass transfer, radiation, Tailor instability,
and buoyancy effect. Realizable k-epsilon model was used for
turbulence modeling. Radiation heat losses were taken into account.
The temperature distribution at seal region is predicted with respect
to heat addition.
Results show the possibilities of the model simplifications by
excluding the water domain in low chamber from calculations. CFD
simulations permit to improve seal chamber design to meet target
water temperature around the seal. This study can be used for the
analysis of different seal chamber configurations.
Abstract: The study of interaction among the grain, moisture,
and the surrounding space (air) is key to understanding the graindrying
process. In Iran, rice (mostly Indica type) is dried by flat
bed type dryer until the final MC reaches to 6 to 8%. The
experiments were conducted to examine the effect of application of
discharge fan with different heights of paddy on the drying
efficiency. Experiments were designed based on two different
configurations of the drying methods; with and without discharge
fan with three different heights of paddy including; 5, 10, and 15
cm. The humid heated air will be going out immediately by the
suction of discharge fan. The drying time is established upon the
average final MC to achieve about 8%. To save energy and reduce
the drying time, the distribution of temperature between layers
should be fast and uniform with minimum difference; otherwise
the difference of MC gradient between layers will be high and will
induce grain breakage. The difference of final MC between layers
in the two methods was 48-73%. The steady state of temperature
between the two methods has saved time in the range of 10-20%,
and the efficiency of temperature distribution increased 17-26% by
the use of discharge fan.
Abstract: In this paper we will consider the most known ratios
control schemes ((L/D, V/B),(L/D,V/F), Ryskamp-s, and
(D/(L+D),V/B)) for binary distillation column and we compare them
in the basis of interactions and disturbance propagation. The models
for these configurations are deuced using mathematical
transformations taking the energy balance structure (LV) as a base
model. The dynamic relative magnitude criterion (DRMC) is used to
assess the interactions. The results show that the introduction of
ratios in controlling the column tends to minimize the degree of
interactions between the loops.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.
Abstract: Optical network uses a tool for routing which is called
Latin router. These routers use particular algorithms for routing. In this paper, we present algorithm for configuration of optical network that is optimized regarding previous algorithm. We show that by decreasing the number of hops for source-destination in lightpath number of satisfied request is less. Also we had shown that more than
single-hop lightpath relating single-hop lightpath is better.
Abstract: This paper presents optimal based damping controllers of Unified Power Flow Controller (UPFC) for improving the damping power system oscillations. The design problem of UPFC damping controller and system configurations is formulated as an optimization with time domain-based objective function by means of Adaptive Tabu Search (ATS) technique. The UPFC is installed in Single Machine Infinite Bus (SMIB) for the performance analysis of the power system and simulated using MATLAB-s simulink. The simulation results of these studies showed that designed controller has an tremendous capability in damping power system oscillations.
Abstract: EPA (Ethernet for Plant Automation) resolves the nondeterministic problem of standard Ethernet and accomplishes real-time communication by means of micro-segment topology and deterministic scheduling mechanism. This paper studies the real-time performance of EPA periodic data transmission from theoretical and experimental perspective. By analyzing information transmission characteristics and EPA deterministic scheduling mechanism, 5 indicators including delivery time, time synchronization accuracy, data-sending time offset accuracy, utilization percentage of configured timeslice and non-RTE bandwidth that can be used to specify the real-time performance of EPA periodic data transmission are presented and investigated. On this basis, the test principles and test methods of the indicators are respectively studied and some formulas for real-time performance of EPA system are derived. Furthermore, an experiment platform is developed to test the indicators of EPA periodic data transmission in a micro-segment. According to the analysis and the experiment, the methods to improve the real-time performance of EPA periodic data transmission including optimizing network structure, studying self-adaptive adjustment method of timeslice and providing data-sending time offset accuracy for configuration are proposed.
Abstract: Chatter vibration has been a troublesome problem for a
machine tool toward the high precision and high speed machining.
Essentially, the machining performance is determined by the dynamic
characteristics of the machine tool structure and dynamics of cutting
process. Therefore the dynamic vibration behavior of spindle tool
system greatly determines the performance of machine tool. The
purpose of this study is to investigate the influences of the machine
frame structure on the dynamic frequency of spindle tool unit through
finite element modeling approach. To this end, a realistic finite
element model of the vertical milling system was created by
incorporated the spindle-bearing model into the spindle head stock of
the machine frame. Using this model, the dynamic characteristics of
the milling machines with different structural designs of spindle head
stock and identical spindle tool unit were demonstrated. The results of
the finite element modeling reveal that the spindle tool unit behaves
more compliant when the excited frequency approaches the natural
mode of the spindle tool; while the spindle tool show a higher dynamic
stiffness at lower frequency that may be initiated by the structural
mode of milling head. Under this condition, it is concluded that the
structural configuration of spindle head stock associated with the
vertical column of milling machine plays an important role in
determining the machining dynamics of the spindle unit.
Abstract: Hexapod Machine Tool (HMT) is a parallel robot
mostly based on Stewart platform. Identification of kinematic
parameters of HMT is an important step of calibration procedure. In
this paper an algorithm is presented for identifying the kinematic
parameters of HMT using inverse kinematics error model. Based on
this algorithm, the calibration procedure is simulated. Measurement
configurations with maximum observability are decided as the first
step of this algorithm for a robust calibration. The errors occurring in
various configurations are illustrated graphically. It has been shown
that the boundaries of the workspace should be searched for the
maximum observability of errors. The importance of using
configurations with sufficient observability in calibrating hexapod
machine tools is verified by trial calibration with two different
groups of randomly selected configurations. One group is selected to
have sufficient observability and the other is in disregard of the
observability criterion. Simulation results confirm the validity of the
proposed identification algorithm.
Abstract: The purpose of the present study is to analyze the
effect of the target plate-s curvature on the heat transfer in laminar
confined impinging jet flows. Numerical results from two
dimensional compressible finite volume solver are compared
between three different shapes of impinging plates: Flat, Concave
and Convex plates. The remarkable result of this study proves that
the stagnation Nusselt number in laminar range of Reynolds number
based on the slot width is maximum in convex surface and is
minimum in concave plate. These results refuse the previous data in
literature stating the amount of the stagnation Nusselt number is
greater in concave surface related to flat plate configuration.
Abstract: A two dimensional three segments coupled pendulum system that mathematically models human arm configuration was developed along with constructing and solving the equations of motions for this model using the energy (work) based approach of Lagrange. The equations of motion of the model were solved iteratively both as an initial value problem and as a two point boundary value problem. In the initial value problem solutions, both the initial system configuration (segment angles) and initial system velocity (segment angular velocities) were used as inputs, whereas, in the two point boundary value problem solutions initial and final configurations and time were used as inputs to solve for the trajectory of motion. The results suggest that the model solutions are sensitive to small changes in the dynamic forces applied to the system as well as to the initial and boundary conditions used. To overcome the system sensitivity a new approach is suggested.