Abstract: Perth will run out of available sustainable natural
water resources by 2015 if nothing is done to slow usage rates,
according to a Western Australian study [1]. Alternative water
technology options need to be considered for the long-term
guaranteed supply of water for agricultural, commercial, domestic
and industrial purposes. Seawater is an alternative source of water for
human consumption, because seawater can be desalinated and
supplied in large quantities to a very high quality.
While seawater desalination is a promising option, the technology
requires a large amount of energy which is typically generated from
fossil fuels. The combustion of fossil fuels emits greenhouse gases
(GHG) and, is implicated in climate change. In addition to
environmental emissions from electricity generation for desalination,
greenhouse gases are emitted in the production of chemicals and
membranes for water treatment. Since Australia is a signatory to the
Kyoto Protocol, it is important to quantify greenhouse gas emissions
from desalinated water production.
A life cycle assessment (LCA) has been carried out to determine
the greenhouse gas emissions from the production of 1 gigalitre (GL)
of water from the new plant. In this LCA analysis, a new desalination
plant that will be installed in Bunbury, Western Australia, and known
as Southern Seawater Desalinization Plant (SSDP), was taken as a
case study. The system boundary of the LCA mainly consists of three
stages: seawater extraction, treatment and delivery. The analysis
found that the equivalent of 3,890 tonnes of CO2 could be emitted
from the production of 1 GL of desalinated water. This LCA analysis
has also identified that the reverse osmosis process would cause the
most significant greenhouse emissions as a result of the electricity
used if this is generated from fossil fuels
Abstract: The review performed on the condition of energy
consumption & rate in Iran, shows that unfortunately the subject of
optimization and conservation of energy in active industries of
country lacks a practical & effective method and in most factories,
the energy consumption and rate is more than in similar industries of
industrial countries. The increasing demand of electrical energy and
the overheads which it imposes on the organization, forces
companies to search for suitable approaches to optimize energy
consumption and demand management. Application of value
engineering techniques is among these approaches. Value
engineering is considered a powerful tool for improving profitability.
These tools are used for reduction of expenses, increasing profits,
quality improvement, increasing market share, performing works in
shorter durations, more efficient utilization of sources & etc.
In this article, we shall review the subject of value engineering and
its capabilities for creating effective transformations in industrial
organizations, in order to reduce energy costs & the results have
been investigated and described during a case study in Mazandaran
wood and paper industries, the biggest consumer of energy in north
of Iran, for the purpose of presenting the effects of performed tasks
in optimization of energy consumption by utilizing value engineering
techniques in one case study.
Abstract: It is impossible to think about democracy without elections. The litmus test of any electoral process in any country is the possibility of a one time minority to become a majority at another time and a peaceful transition of power. In many countries in Sub-Saharan Africa though the multi-party elections appeared to be competitive they failed the acid test of democracy: peaceful regime change in a free and fair election. Failure to solve electoral disputes might lead to bloody electoral conflicts as witnessed in many emerging democracies in Africa. The aim of this paper is to investigate electoral conflicts in Africa since the end of the Cold War by using the 2005 post-election violence in Ethiopia as a case study. In Ethiopia, the coming to power of the EPRDF in 1991 marked the fall of the Derg dictatorial military government and the beginning of a multi-party democracy. The country held multi-party parliamentary elections in 1995, 2000, and 2005 where the ruling EPRDF party “won" the elections through violence, involving intimidation, manipulation, detentions of political opponents, torture, and political assassinations. The 2005 electoral violence was the worst electoral violence in the country-s political history that led to the death of 193 protestors and the imprisonment of more than 40, 000 people. It is found out that the major causes of the 2005 Ethiopian election were the defeat of the ruling party in the election and its attempt to reverse the poll results by force; the Opposition-s lack of decisive leadership; the absence of independent courts and independent electoral management body; and the ruling party-s direct control over the army and police.
Abstract: Supply Chain Management (SCM) is the integration
between manufacturer, transporter and customer in order to form one
seamless chain that allows smooth flow of raw materials, information
and products throughout the entire network that help in minimizing
all related efforts and costs. The main objective of this paper is to
develop a model that can accept a specified number of spare-parts
within the supply chain, simulating its inventory operations
throughout all stages in order to minimize the inventory holding
costs, base-stock, safety-stock, and to find the optimum quantity of
inventory levels, thereby suggesting a way forward to adapt some
factors of Just-In-Time to minimizing the inventory costs throughout
the entire supply chain. The model has been developed using Micro-
Soft Excel & Visual Basic in order to study inventory allocations in
any network of the supply chain. The application and reproducibility
of this model were tested by comparing the actual system that was
implemented in the case study with the results of the developed
model. The findings showed that the total inventory costs of the
developed model are about 50% less than the actual costs of the
inventory items within the case study.
Abstract: Most of the real queuing systems include special properties and constraints, which can not be analyzed directly by using the results of solved classical queuing models. Lack of Markov chains features, unexponential patterns and service constraints, are the mentioned conditions. This paper represents an applied general algorithm for analysis and optimizing the queuing systems. The algorithm stages are described through a real case study. It is consisted of an almost completed non-Markov system with limited number of customers and capacities as well as lots of common exception of real queuing networks. Simulation is used for optimizing this system. So introduced stages over the following article include primary modeling, determining queuing system kinds, index defining, statistical analysis and goodness of fit test, validation of model and optimizing methods of system with simulation.
Abstract: The increased use of biodiesel implies variations on both greenhouse gases and air pollutant emissions. Some studies point out that the use of biodiesel blends on diesel can help in controlling air pollution and promote a reduction of CO2 emissions. Reductions on PM, SO2, VOC and CO emissions are also expected, however NOx emissions may increase, which may potentiate O3 formation. This work aims to assess the impact of the biodiesel use on air quality, through a numerical modeling study, taking the Northern region of Portugal as a case study. The emission scenarios are focused on 2008 (baseline year) and 2020 (target year of Renewable Energy Directive-RED) and on three biodiesel blends (B0, B10 and B20). In a general way the use of biodiesel by 2020 will reduce the CO2 and air pollutants emissions in the Northern Portugal, improving air quality. However it will be in a very small extension.
Abstract: Power transformer consists of components which are
under consistent thermal and electrical stresses. The major
component which degrades under these stresses is the paper
insulation of the power transformer. At site, lightning impulses and
cable faults may cause the winding deformation. In addition, the
winding may deform due to impact during transportation. A
deformed winding will excite more stress to its insulating paper thus
will degrade it. Insulation degradation will shorten the life-span of
the transformer. Currently there are two methods of detecting the
winding deformation which are Sweep Frequency Response
Analysis (SFRA) and Low Voltage Impulse Test (LVI). The latter
injects current pulses to the winding and capture the admittance
plot. In this paper, a transformer which experienced overheating and
arcing was identified, and both SFRA and LVI were performed.
Next, the transformer was brought to the factory for untanking. The
untanking results revealed that the LVI is more accurate than the
SFRA method for this case study.
Abstract: In most of the cases, natural disasters lead to the
necessity of evacuating people. The quality of evacuation
management is dramatically improved by the use of information
provided by decision support systems, which become indispensable
in case of large scale evacuation operations. This paper presents a
best practice case study. In November 2007, officers from the
Emergency Situations Inspectorate “Crisana" of Bihor County from
Romania participated to a cross-border evacuation exercise, when
700 people have been evacuated from Netherlands to Belgium. One
of the main objectives of the exercise was the test of four different
decision support systems. Afterwards, based on that experience,
software system called TEVAC (Trans Border Evacuation) has been
developed “in house" by the experts of this institution. This original
software system was successfully tested in September 2008, during
the deployment of the international exercise EU-HUROMEX 2008,
the scenario involving real evacuation of 200 persons from Hungary
to Romania. Based on the lessons learned and results, starting from
April 2009, the TEVAC software is used by all Emergency
Situations Inspectorates all over Romania.
Abstract: The objective of this research is to investigate the
advantages of using large-diameter 0.7 inch prestressing strands in
pretention applications. The advantages of large-diameter strands are
mainly beneficial in the heavy construction applications. Bridges and
tunnels are subjected to a higher daily traffic with an exponential
increase in trucks ultimate weight, which raise the demand for higher
structural capacity of bridges and tunnels. In this research, precast
prestressed I-girders were considered as a case study. Flexure
capacities of girders fabricated using 0.7 inch strands and different
concrete strengths were calculated and compared to capacities of 0.6
inch strands girders fabricated using equivalent concrete strength.
The effect of bridge deck concrete strength on composite deck-girder
section capacity was investigated due to its possible effect on final
section capacity. Finally, a comparison was made to compare the
bridge cross-section of girders designed using regular 0.6 inch strands
and the large-diameter 0.7 inch. The research findings showed that
structural advantages of 0.7 inch strands allow for using fewer bridge
girders, reduced material quantity, and light-weight members. The
structural advantages of 0.7 inch strands are maximized when high
strength concrete (HSC) are used in girder fabrication, and concrete
of minimum 5ksi compressive strength is used in pouring bridge
decks. The use of 0.7 inch strands in bridge industry can partially
contribute to the improvement of bridge conditions, minimize
construction cost, and reduce the construction duration of the project.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. Many areas are being developed and therefore require additional electrical power to comply with the demand. Substation upgrade is one of the rapid solutions to ensure the continuous supply of power to customers. This upgrade requires civil modifications to structures and fences. The civil work requires excavation and steel works that may create unsafe touch conditions. This paper presents a brief theoretical overview of the touch voltage inside and around substations and uses CDEGS software to simulate a case study.
Abstract: E-travel is travel agency-s companies employing internet and website as e-commerce context. This study presents numerous initial key factors of electronic travel model based on small travel agencies perspectives. Browsing previous studies related to website travel activities are conducted. Five small travel agencies in Indonesia has been deeply interviewed in case studies. The finding of this research is identifying numerous characteristics and dimension factors and travel website operations including ownermanager roles, business experiences, characteristically business, and technological aspects. This study is the preliminary research related to travel website adoption in Indonesia. The further study would be conducted in questionnaires of the quantitative research in Indonesia contexts as a developing country.
Abstract: This study examines the possibility to apply the theory of multidimensional accounting (momentum accounting) in a Brazilian Navy-s Services Provider Military Organization (Organização Militar Prestadora de Serviços - OMPS). In general, the core of the said theory is the fact that Accounting does not recognize the inertia of transactions occurring in an entity, and that occur repeatedly in some cases, regardless of the implementation of new actions by its managers. The study evaluates the possibility of greater use of information recorded in the financial statements of the unit of analysis, within the strategic decisions of the organization. As a research strategy, we adopted the case study. The results infer that it is possible to use the theory in the context of a multidimensional OMPS, promoting useful information for decision-making and thereby contributing to the strengthening of the necessary alignment of its administration with the current desires of the Brazilian society.
Abstract: In the present article, effect of non-uniform excitation
of reservoir bottom on nonlinear response of concrete gravity dams is
considered. Anisotropic damage mechanics approach is used to model nonlinear behavior of mass concrete in 2D space. The tallest
monolith of Pine Flat dam is selected as a case study. The horizontal
and vertical components of 1967 Koyna earthquake is used to excite
the system. It is found that crest response and stresses within the dam body decrease significantly when the reservoir is excited nonuniformly. In addition, the crack profiles within the dam body and in vicinity of the neck decreases.
Abstract: This paper contributes to the field of Environmental
Awareness Training (EAT) evaluation in terms of military activities.
Environmental management of military activities is a growing concern
for defence forces worldwide and the importance of EAT is becoming
widely recognized. As one of Australia-s largest landowners, the
Australian Defence Force (ADF) is extremely mindful of its duty as a
joint environmental manager. It has an integrated Environmental
Management System (EMS) to assist environmental management and
EAT is an essential part of the ADF EMS model. This paper examines
how EAT was conducted during the exercise Talisman Saber in 2009
(TS09) and evaluates its effectiveness, using Shoalwater Bay Training
Area (SWBTA), one of the most significant military training areas and
a significant protected area in Australia, as a case study. A
questionnaire survey conducted showed, overall, that EAT was
effective from the perspective of a sample of participants.
Recommendations are made for the ADF to refine EAT for future
exercises.
Abstract: This paper aims to study at the use of local knowledge
to develop community self-protection in flood prone residential area,
Ayutthaya Island has been chosen as a case study. This study tries to
examine the strength of local knowledge which is able to develop
community self-protection and cope with flood disaster. In-depth, this
paper focuses on the influence of social network on knowledge
transfer. After conducted the research, authors reviewed the strength
of local knowledge and also mentioned the obstacles of community to
use and also transfer local knowledge. Moreover, the result of the
study revealed that local knowledge is not always transferred by the
strongest-tie social network (family or kinship) as we used to believe.
Surprisingly, local knowledge could be also transferred by the
weaker-tie social network (teacher/ monk) with the better
effectiveness in some knowledge.
Abstract: Fuzzy logic control (FLC) systems have been tested in
many technical and industrial applications as a useful modeling tool
that can handle the uncertainties and nonlinearities of modern control
systems. The main drawback of the FLC methodologies in the
industrial environment is challenging for selecting the number of
optimum tuning parameters.
In this paper, a method has been proposed for finding the optimum
membership functions of a fuzzy system using particle swarm
optimization (PSO) algorithm. A synthetic algorithm combined from
fuzzy logic control and PSO algorithm is used to design a controller
for a continuous stirred tank reactor (CSTR) with the aim of
achieving the accurate and acceptable desired results. To exhibit the
effectiveness of proposed algorithm, it is used to optimize the
Gaussian membership functions of the fuzzy model of a nonlinear
CSTR system as a case study. It is clearly proved that the optimized
membership functions (MFs) provided better performance than a
fuzzy model for the same system, when the MFs were heuristically
defined.
Abstract: System-level design based on high-level abstractions
is becoming increasingly important in hardware and embedded
system design. This paper analyzes meta-design techniques oriented
at developing meta-programs and meta-models for well-understood
domains. Meta-design techniques include meta-programming and
meta-modeling. At the programming level of design process, metadesign
means developing generic components that are usable in a
wider context of application than original domain components. At the
modeling level, meta-design means developing design patterns that
describe general solutions to the common recurring design problems,
and meta-models that describe the relationship between different
types of design models and abstractions. The paper describes and
evaluates the implementation of meta-design in hardware design
domain using object-oriented and meta-programming techniques.
The presented ideas are illustrated with a case study.