Abstract: In this study, the precipitation conditions of Chevreul’s salt were evaluated. The structure of Chevreul’s salt was examined by considering the previous studies. Thermodynamically, the most important precipitation parameters were pH, temperature, and sulphite-copper(II) ratio. The amount of Chevreul’s salt increased with increasing the temperature and sulphite-copper(II) ratio at the certain range, while it increased with decreasing the pH value at the chosen range. The best solution medium for recovery of Chevreul’s salt is sulphur dioxide gas-water system. Moreover, the soluble sulphite salts are used as efficient precipitating reagents. Chevreul’s salt is generally used to produce the highly pure copper powders from synthetic copper sulphate solutions and impure leach solutions. When the pH of the initial ammoniacal solution is greater than 8.5, ammonia in the medium is not free, and Chevreul’s salt from solution does not precipitate. In contrast, copper ammonium sulphide is precipitated. The pH of the initial solution containing ammonia for precipitating of Chevreul’s salt must be less than 8.5.
Abstract: In this study, Chevreul’s salt was dissolved in ammonium chloride solutions. All experiments were performed in a batch reactor. The obtained results were optimized. Parameters used in the experiments were the reaction temperature, the ammonium chloride concentration, the reaction time and the solid-to-liquid ratio. The optimum conditions were determined by 24 factorial experimental design method. The best values of four parameters were determined as based on the experiment results. After the evaluation of experiment results, all parameters were found as effective in experiment conditions selected. The optimum conditions on the maximum Chevreul’s salt dissolution were the ammonium chloride concentration 4.5 M, the reaction time 13.2 min., the reaction temperature 25 oC, and the solid-to-liquid ratio 9/80 g.mL-1. The best dissolution yield in these conditions was 96.20%.
Abstract: Conventional wastewater treatment plants of activated carbon, electrodialysis, ion exchange, reverse osmosis etc. are expensive to install, operate and maintain especially in developing countries; therefore, the use of aquatic macrophytes for wastewater purification is a viable alternative. On the first day of experimentation, approximately 100g of water hyacinth was introduced into the hydroponic units in four replicates. The water quality parameters measured were total suspended solids (TSS), pH and electrical conductivity (EC). Others were concentration of ammonium–nitrogen (NH4+-N), nitrite-nitrogen (NO2--N), nitrate-nitrogen (NO3--N), phosphate–phosphorus (PO43--P), and biomass value. At phytoremediation intervals of 7, 14, 21 and 28 days, the biomass recorded were 438.2 g, 600.7 g, 688.2 g and 725.7 g. Water hyacinth was able to reduce the pollutant concentration of all the selected parameter. The percentage reduction of pH ranged from 1.9% to 14.7%, EC from 49.8% to 97.0%, TDS from 50.4% to 97.6%, TSS from 34.0% to 78.3%, NH4+-N from 38.9% to 85.2%, NO2--N from 0% to 84.6%, NO3--N from 63.2% to 98.8% and PO43--P from 10% to 88.0%. Paired sample t-test shows that at 95% confidence level, it can be concluded statistically that the inequality between the pre-treatment and post-treatment values are significant. This suggests that the use of water hyacinth is valuable in the design and operation of aquaculture effluent treatment and should therefore be adopted by environmental and wastewater managers.
Abstract: Pollutants from aquacultural practices constitute environmental problems and phytoremediation could offer cheaper environmentally sustainable alternative since equipment using advanced treatment for fish tank effluent is expensive to import, install, operate and maintain, especially in developing countries. The main objective of this research was, therefore, to develop a mathematical model for phytoremediation by aquatic plants in aquaculture wastewater. Other objectives were to evaluate the retention times on phytoremediation rates using the model and to measure the nutrient level of the aquaculture effluent and phytoremediation rates of three aquatic macrophytes, namely; water hyacinth (Eichornia crassippes), water lettuce (Pistial stratoites) and morning glory (Ipomea asarifolia). A completely randomized experimental design was used in the study. Approximately 100 g of each macrophyte were introduced into the hydroponic units and phytoremediation indices monitored at 8 different intervals from the first to the 28th day. The water quality parameters measured were pH and electrical conductivity (EC). Others were concentration of ammonium–nitrogen (NH4+ -N), nitrite- nitrogen (NO2- -N), nitrate- nitrogen (NO3- -N), phosphate –phosphorus (PO43- -P), and biomass value. The biomass produced by water hyacinth was 438.2 g, 600.7 g, 688.2 g and 725.7 g at four 7–day intervals. The corresponding values for water lettuce were 361.2 g, 498.7 g, 561.2 g and 623.7 g and for morning glory were 417.0 g, 567.0 g, 642.0 g and 679.5g. Coefficient of determination was greater than 80% for EC, TDS, NO2- -N, NO3- -N and 70% for NH4+ -N using any of the macrophytes and the predicted values were within the 95% confidence interval of measured values. Therefore, the model is valuable in the design and operation of phytoremediation systems for aquaculture effluent.
Abstract: Despite the wide spread use of synthetic dyes, natural
dyes are still exploited and used to enhance its inherent aesthetic
qualities as a major material for beautification of the body. Centuries
before the discovery of synthetic dyes, natural dyes were the only
source of dye open to mankind. Dyes are extracted from plant -
leaves, roots and barks, insect secretions, and minerals. However,
research findings have made it clear that of all, plants- leaves, roots,
barks or flowers are the most explored and exploited in which henna
(Lawsonia innermis L.) is one of those plants. Experiment has also
shown that henna is used in body painting in conjunction with an
alkaline (Ammonium Sulphate) as a fixing agent. This of course
gives a clue that if colour derived from henna is properly
investigated, it may not only be used for body decoration but
possibly, may have affinity to fiber substrate. This paper investigates
the dyeing potentials – dye ability and fastness qualities of henna dye
extracts on cotton and linen fibers using mordants like ammonium
sulphate and other alkalis (hydrosulphate and caustic soda, potash,
common salt, potassium alum). Hot and cold water and ethanol
solvent were used in the extraction of the dye to investigate the most
effective method, dye ability, and fastness qualities of these extracts
under room temperature. The results of the experiment show that
cotton have a high rate of dye intake than other fiber. On a similar
note, the colours obtained depend most on the solvent used. In
conclusion, hot water extraction appears more effective. While the
colours obtained from ethanol and both cold hot methods of
extraction range from light to dark yellow, light green to army green
and to some extent shades of brown hues.
Abstract: Chitosan polyacrylic acid composite membranes were
prepared by a bulk polymerization method in presence of N, N'-
methylene bisacrylamide (crosslinker) and ammonium persulphate as
initiator. Membranes prepared from this copolymer in presence and
absence of Ag nanoparticles were characterized by measuring
mechanical and physical properties, water up-take and antibacterial
properties. The results obtained indicated that the prepared
membranes have antibacterial properties which increase with adding
Ag nanoparticles.
Abstract: The influence of cultivation factors such as content of ammonium sulfate, glucose and water in the culture medium and particle size of dry orange waste, on their bioconversion for pectinase production was studied using complete factorial design. A polygalacturonase (PG) was isolated using ion exchange chromatography under gradient elution 0-0,5 m/l NaCl (column equilibrate with acetate buffer pH 4,5), subsequently by sephadex G75 column chromatography was applied and the molecular weight was obtained about 51,28 KDa. Purified PG enzyme exhibits a pH and temperature optima of activity at 5 and 35°C respectively. Treatment of apple juice by purified enzyme extract yielded a clear juice, which was competitive with juice yielded by pure Sigma Aldrich Aspergillus niger enzyme.
Abstract: Anammox is a novel and promising technology that has changed the traditional concept of biological nitrogen removal. The process facilitates direct oxidation of ammonical nitrogen under anaerobic conditions with nitrite as an electron acceptor without addition of external carbon sources. The present study investigated the feasibility of Anammox Hybrid Reactor (AHR) combining the dual advantages of suspended and attached growth media for biodegradation of ammonical nitrogen in wastewater. Experimental unit consisted of 4 nos. of 5L capacity AHR inoculated with mixed seed culture containing anoxic and activated sludge (1:1). The process was established by feeding the reactors with synthetic wastewater containing NH4-H and NO2-N in the ratio 1:1 at HRT (hydraulic retention time) of 1 day. The reactors were gradually acclimated to higher ammonium concentration till it attained pseudo steady state removal at a total nitrogen concentration of 1200 mg/l. During this period, the performance of the AHR was monitored at twelve different HRTs varying from 0.25-3.0 d with increasing NLR from 0.4 to 4.8 kg N/m3d. AHR demonstrated significantly higher nitrogen removal (95.1%) at optimal HRT of 1 day. Filter media in AHR contributed an additional 27.2% ammonium removal in addition to 72% reduction in the sludge washout rate. This may be attributed to the functional mechanism of filter media which acts as a mechanical sieve and reduces the sludge washout rate many folds. This enhances the biomass retention capacity of the reactor by 25%, which is the key parameter for successful operation of high rate bioreactors. The effluent nitrate concentration, which is one of the bottlenecks of anammox process was also minimised significantly (42.3-52.3 mg/L). Process kinetics was evaluated using first order and Grau-second order models. The first-order substrate removal rate constant was found as 13.0 d-1. Model validation revealed that Grau second order model was more precise and predicted effluent nitrogen concentration with least error (1.84±10%). A new mathematical model based on mass balance was developed to predict N2 gas in AHR. The mass balance model derived from total nitrogen dictated significantly higher correlation (R2=0.986) and predicted N2 gas with least error of precision (0.12±8.49%). SEM study of biomass indicated the presence of heterogeneous population of cocci and rod shaped bacteria of average diameter varying from 1.2-1.5 mm. Owing to enhanced NRE coupled with meagre production of effluent nitrate and its ability to retain high biomass, AHR proved to be the most competitive reactor configuration for dealing with nitrogen laden wastewater.
Abstract: In this research, thorium dioxide mesoporous
nanocrystalline powder was synthesized through the sol-gel method
using hydrated thorium nitrate and ammonium hydroxide as starting
materials and Triton X100 as surfactant. ThO2 gel was characterized
by thermogravimetric (TGA), and prepared ThO2 powder was
subjected to scanning electron microscopy (SEM), X-ray diffraction
(XRD), and Brunauer-Emett-Teller (BET) analyses studies. Detailed
analyses show that prepared powder consisted of phase with the
space group Fm3m of thoria and its crystalline size was 12.6 nm. The
thoria possesses 16.7 m2/g surface area and the pore volume and size
calculated to be 0.0423 cc/g and 1.947 nm, respectively.
Abstract: This paper presents the influences on the entrainment
of serpentines by grinding and reagents during copper–nickel sulfide
flotation. The previous bench flotation tests were performed to extract
the metallic values from the ore in Yunnan Mine, China and the
relatively satisfied results with recoveries of 86.92% Cu, 54.92% Ni,
and 74.73% Pt+Pd in the concentrate were harvested at their grades of
4.02%, 3.24% and 76.61 g/t, respectively. However, the content of
MgO in the concentrate was still more than 19%. Micro-flotation tests
were conducted with the objective of figuring out the influences on the
entrainment of serpentines into the concentrate by particle size,
flocculants or depressants and collectors, as well as visual
observations in suspension by OLYMPUS camera. All the tests results
pointed to the presences of both “entrapped-in” serpentines and its
coating on the hydrophobic flocs resulted from strong collectors
(combination of butyl xanthate, butyl ammonium dithophosphate,
even after adding carboxymethyl cellulose as effective depressant.
And fine grinding may escalate the entrainment of serpentines in the
concentrate.
Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.
Abstract: The aim of the present study was to examine whether
increasing molybdenum (Mo) concentration affects the growth and
Mo concentration of maize (Zea mays L. cv Norma SC) and
sunflower (Helianthus annuus L. cv Arena PR) seedlings within
laboratory conditions.
In this experiment, calcareous chernozem soil was used and Mo
was supplemented into the soil as ammonium molybdate
[(NH4)6Mo7O24.4H2O] in four different concentrations as follow: 0
(control), 30, 90 and 270 mg·kg-1.
In this study, we found that molybdenum in small amount (30
mg·kg-1) affects positively on growth of maize and sunflower
seedlings, however, higher concentration of Mo reduces the dry
weights of shoots and roots. In the case of maize the highest Mo
treatment (270 mg·kg-1) and in sunflower 90 mg·kg-1 treatment
caused significant reduction in plant growth.
In addition, we observed that molybdenum contents in the roots
and shoots were very low in case of control soil but were
significantly elevated with increasing concentration of Mo treatment.
Only in case of sunflower the highest 270 mg·kg-1 Mo treatment
caused decrease in Mo concentration.
Abstract: Gypsum (CaSO4.2H2O) is a mineral that is found in
large quantities in the Turkey and in the World. In this study, the
dissolution of this mineral in the diammonium hydrogen phosphate
solutions has been studied. The dissolution and dissolution kinetics of
gypsum in diammonium hydrogen phosphate solutions will be useful
for evaluating of solid wastes containing gypsum. Parameters such as
diammonium hydrogen phosphate concentration, temperature and
stirring speed affecting on the dissolution rate of the gypsum in
diammonium hydrogen phosphate solutions were investigated. In
experimental studies have researched effectiveness of the selected
parameters. The dissolution of gypsum were examined in two parts at
low and high temperatures. The experimental results were
successfully correlated by linear regression using Statistica program.
Dissolution curves were evaluated shrinking core models for solidfluid
systems. The activation energy was found to be 34.58 kJ/mol
and 44.45 kJ/mol for the low and the high temperatures. The
dissolution of gypsum was controlled by chemical reaction both low
temperatures and high temperatures.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: A Silver (Ag) thin film is introduced as a template and
doping source for vertically aligned p–type ZnO nanorods. ZnO
nanorods were grown using an ammonium hydroxide based
hydrothermal process. During the hydrothermal process, the Ag thin
film was dissolved to generate Ag ions in the solution. The Ag ions can
contribute to doping in the wurzite structure of ZnO and the (111)
grain of Ag thin film can be the epitaxial temporal template for the
(0001) plane of ZnO. Hence, Ag–doped p–type ZnO nanorods were
successfully grown on the substrate, which can be an electrode or
semiconductor for the device application. To demonstrate the
potentials of this idea, p–n diode was fabricated and its electrical
characteristics were demonstrated.
Abstract: In this work, a polyaniline/Iron oxide (PANI/Fe2O3)
composite was chemically prepared by oxidative polymerization of
aniline in acid medium, in presence of ammonium persulphate as an
oxidant and amount of Fe2O3. The composite was characterized by a
scanning electron microscopy (SEM). The prepared composite has
been used as adsorbent to remove Tartrazine dye form aqueous
solutions.
The effects of initial dye concentration and temperature on the
adsorption capacity of PANI/Fe2O3 for Tartrazine dye have been
studied in this paper.
The Langmuir and Freundlich adsorption models have been used
for the mathematical description of adsorption equilibrium data. The
best fit is obtained using the Freundlich isotherm with an R2 value of
0.998. The change of Gibbs energy, enthalpy, and entropy of
adsorption has been also evaluated for the adsorption of Tartrazine
onto PANI/ Fe2O3. It has been proved according the results that the
adsorption process is endothermic in nature.
Abstract: This work details the generation of thin films of
structured zeolite catalysts (ZSM–5 and Y) onto the surface of a
metal substrate (FeCrAlloy) using in-situ hydrothermal synthesis. In
addition, the zeolite Y is post-synthetically modified by acidified
ammonium ion exchange to generate US-Y. Finally the catalytic
activity of the structured ZSM-5 catalyst films (Si/Al = 11, thickness
146 0m) and structured US–Y catalyst film (Si/Al = 8, thickness
230m) were compared with the pelleted powder form of ZSM–5 and
USY catalysts of similar Si/Al ratios.
The structured catalyst films have been characterised using a range
of techniques, including X-ray diffraction (XRD), Electron
microscopy (SEM), Energy Dispersive X–ray analysis (EDX) and
Thermogravimetric Analysis (TGA). The transition from oxide-onalloy
wires to hydrothermally synthesised uniformly zeolite coated
surfaces was followed using SEM and XRD. In addition, the
robustness of the prepared coating was confirmed by subjecting these
to thermal cycling (ambient to 550oC).
The cracking of n–heptane over the pellets and structured catalysts
for both ZSM–5 and Y zeolite showed very similar product
selectivities for similar amounts of catalyst with an apparent
activation energy of around 60 kJ mol-1. This paper demonstrates that
structured catalysts can be manufactured with excellent zeolite
adherence and when suitably activated/modified give comparable
cracking results to the pelleted powder forms. These structured
catalysts will improve temperature distribution in highly exothermic
and endothermic catalysed processes.
Abstract: Ammonium nitrate (AN) is produced by the reaction of ammonia and nitric acid, and a waste condensate is obtained. The condensate contains pure AN in concentration up to 10g/L. The salt content in the condensate is too high to discharge immediately into the river thus it must be treated. This study is concerned with the treatment of condensates from an industrial AN production by combination of electrodialysis (ED) and electrodeionization (EDI). The condensate concentration was in range 1.9–2.5g/L of AN. A pilot ED module with 25 membrane pairs following by a laboratory EDI module with 10 membrane pairs operated continuously during 800 hours. Results confirmed that the combination of ED and EDI is suitable for the condensate treatment.
Abstract: Coagulation is a process that sanitizes leather effluents. It aims to reduce pollutants such as Chemical Oxygen Demand (COD), chloride, sulfate, chromium, suspended solids, and other dissolved solids. The current study aimed to evaluate coagulation efficiency of tannery wastewater by analyzing the change in organic matter, odor, color, ammonium ions, nutrients, chloride, H2S, sulfate, suspended solids, total dissolved solids, fecal pollution, and chromium hexavalent before and after treatment. Effluent samples were treated with coagulants Ca(OH)2 and FeSO4 .7H2O. The best advantages of this treatment included the removal of: COD (81.60%); ammonia ions (98.34%); nitrate ions (92%); chromium hexavalent (75.00%); phosphate (70.00%); chloride (69.20%); and H₂S (50%). Results also indicated a high level of efficiency in the reduction of fecal pollution indicators. Unfortunately, only a modest reduction of sulfate (19.00%) and TSS (13.00%) and an increase in TDS (15.60%) was observed.
Abstract: Homogeneous graft copolymerization of methyl methacrylate (MMA) onto cellulose was carried out in N, N – dimethyl acetamide/LiCl (DMAc/LiCl) and dimethyl sulfoxide/ paraformaldehyde (DMSO/PF) solvent system taking ceric ammonium nitrate (CAN), benzoyl peroxide (BPO) and tin (II)-2-ethyl hexanoate [Sn(Oct)2] as initiators. Different grafting parameters like graft yield (GY), grafting efficiency (GE) and total conversion of monomer to polymer (TC) were evaluated at different reaction conditions of temperature, time, and variation of the amount of monomer and initiator. The viscosity average molecular weight of grafted PMMA and number of grafts per cellulose chain were also calculated. The products were characterized by FT-IR and 1H-NMR analyses and possible reaction mechanisms were deduced. Thermal degradation of the grafted products was also studied by thermo-gravimetric analysis (TG) and differential thermo-gravimetry (DTG).