Abstract: In this paper the influence of heterogeneous traffic on
the temporal variation of ambient PM10, PM2.5 and PM1
concentrations at a busy arterial route (Sardar Patel Road) in the
Chennai city has been analyzed. The hourly PM concentration, traffic
counts and average speed of the vehicles have been monitored at the
study site for one week (19th-25th January 2009). Results indicated
that the concentrations of coarse (PM10) and fine PM (PM2.5 and
PM1) concentrations at SP road are having similar trend during peak
and non-peak hours, irrespective of the days. The PM concentrations
showed daily two peaks corresponding to morning (8 to 10 am) and
evening (7 to 9 pm) peak hour traffic flow. The PM10 concentration is
dominated by fine particles (53% of PM2.5 and 45% of PM1). The
high PM2.5/PM10 ratio indicates that the majority of PM10 particles
originate from re-suspension of road dust. The analysis of traffic flow
at the study site showed that 2W, 3W and 4W are having similar
diurnal trend as PM concentrations. This confirms that the 2W, 3W
and 4W are the main emission source contributing to ambient PM
concentration at SP road. The speed measurement at SP road showed
that the average speed of 2W, 3W, 4W, LCV and HCV are 38, 40,
38, 40 and 38 km/hr and 43, 41, 42, 40 and 41 km/hr respectively for
the weekdays and weekdays.
Abstract: The purpose of suspension system in automobiles is to
improve the ride comfort and road handling. In this research the ride
and handling performance of a specific automobile with passive
suspension system is compared to a proposed fuzzy logic semi active
suspension system designed for that automobile. The bodysuspension-
wheel system is modeled as a two degree of freedom
quarter car model. MATLAB/SIMULINK [1] was used for
simulation and controller design. The fuzzy logic controller is based
on two inputs namely suspension velocity and body velocity. The
output of the fuzzy controller is the damping coefficient of the
variable damper. The result shows improvement over passive
suspension method.
Abstract: Overhead electrical insulators form an important link in an electric power system. Along with the traditional insulators (i.e. glass and porcelain, etc) presently the polymeric insulators are also used world widely. These polymeric insulators are very sensitive to various environmental parameters such temperature, environmental pollution, UV-radiations, etc. which seriously effect their electrical, chemical and hydrophobic properties. The UV radiation level in the central region of Saudi Arabia is high as compared to the IEC standard for the accelerated aging of the composite insulators. Commonly used suspension type of composite EPDM (Ethylene Propylene Diene Monomer) insulator was subjected to accelerated stress aging as per modified IEC standard simulating the inland arid deserts atmospheric condition and also as per IEC-61109 standard. The hydrophobic characteristics were studied by measuring the contact angle along the insulator surface before and after the accelerated aging of the samples. It was found that EPDM insulator loses it hydrophobic properties proportional to the intensity of UV irradiations and its rate of recovery is also very low as compared to Silicone Rubber insulator.KeywordsEPDM, composite insulators, accelerated aging, hydrophobicity, contact angle.
Abstract: Automotive suspension system is important part of car
comfort and safety. In this article automotive active suspension with
linear motor as actuator is designed using H-infinity control. This
paper is focused on comparison of different controller designed for
quart, half or full-car model (and always used for “full" car). Special
attention is placed on energy demand of the whole system. Each
controller configuration is simulated and then verified on the
hydraulic quarter car test bed.
Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: Using electrical machine in conventional vehicles, also called hybrid vehicles, has become a promising control scheme that enables some manners for fuel economy and driver assist for better stability. In this paper, vehicle stability control, fuel economy and Driving/Regeneration braking for a 4WD hybrid vehicle is investigated by using an electrical machine on each non-driven wheels. In front wheels driven vehicles, fuel economy and regenerative braking can be obtained by summing torques applied on rear wheels. On the other hand, unequal torques applied to rear wheels provides enhanced safety and path correction in steering. In this paper, a model with fourteen degrees of freedom is considered for vehicle body, tires and, suspension systems. Thereafter, powertrain subsystems are modeled. Considering an electrical machine on each rear wheel, a fuzzy controller is designed for each driving, braking, and stability conditions. Another fuzzy controller recognizes the vehicle requirements between the driving/regeneration and stability modes. Intelligent vehicle control to multi objective operation and forward simulation are the paper advantages. For reaching to these aims, power management control and yaw moment control will be done by three fuzzy controllers. Also, the above mentioned goals are weighted by another fuzzy sub-controller base on vehicle dynamic. Finally, Simulations performed in MATLAB/SIMULINK environment show that the proposed structure can enhance the vehicle performance in different modes effectively.
Abstract: Acute toxicity of nano SiO2, ZnO, MCM-41 (Meso
pore silica), Cu, Multi Wall Carbon Nano Tube (MWCNT), Single
Wall Carbon Nano Tube (SWCNT) , Fe (Coated) to bacteria Vibrio
fischeri using a homemade luminometer , was evaluated. The values
of the nominal effective concentrations (EC), causing 20% and 50%
inhibition of biouminescence, using two mathematical models at two
times of 5 and 30 minutes were calculated. Luminometer was
designed with Photomultiplier (PMT) detector. Luminol
chemiluminescence reaction was carried out for the calibration graph.
In the linear calibration range, the correlation coefficients and
coefficient of Variation (CV) were 0.988 and 3.21% respectively
which demonstrate the accuracy and reproducibility of the instrument
that are suitable. The important part of this research depends on how
to optimize the best condition for maximum bioluminescence. The
culture of Vibrio fischeri with optimal conditions in liquid media,
were stirring at 120 rpm at a temperature of 150C to 180C and were
incubated for 24 to 72 hours while solid medium was held at 180C
and for 48 hours. Suspension of nanoparticles ZnO, after 30 min
contact time to bacteria Vibrio fischeri, showed the highest toxicity
while SiO2 nanoparticles showed the lowest toxicity. After 5 min
exposure time, the toxicity of ZnO was the strongest and MCM-41
was the weakest toxicant component.
Abstract: Homogeneous composites of alumina and zirconia
with a small amount of MgO (99%) were obtained for ZTA ceramic containing 0.05 wt% MgO in
1500 °C.
Abstract: In the present paper, Fatigue life assessment of an
anti-roll bar component of a passenger vehicle, is investigated by
ANSYS 11 software. A stress analysis is also carried out by the
finite element technique for the determination of highly stressed
regions on the bar. Anti-roll bar is a suspension element used at the
front, rear, or at both ends of a car that reduces body roll by resisting
any unequal vertical motion between the pair of wheels to which it is
connected. As a first stage, fatigue damage models proposed by some
well-known references and the corresponding assumptions are
discussed and some enhancements are proposed. Then, fracture
analysis of an anti-roll bar of an automobile is carried out. The
analysed type of the anti-roll bar is especially important as many
cases are reported about the fracture after a 100,000 km of travel
fatigue and fracture conditions. This paper demonstrates fatigue life
of an anti-roll bar and then evaluated by experimental analytically
results from other researcher.
Abstract: Deflocculation and gel characterization were
investigated for three different composition of porcelain slips at
specific gravity 1.8. The suspensions were dispersed with sodium
silicate (Na2SiO3) in under-deflocculated slips and fully deflocculated
slips. The rheology characterization of slips was conducted by the
deflocculation curves and the gel curves. The results showed that
decreasing the amount of the ball clay composition in the slips
consumed less dosages of the dispersants. The under-deflocculated
slips tended to have a gelation rate faster than the fully deflocculated
slips.
Abstract: The steady state response of bond graphs representing
passive and active suspension is presented. A bond graph with
preferred derivative causality assignment to get the steady state
is proposed. A general junction structure of this bond graph
is proposed. The proposed methodology to passive and active
suspensions is applied.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: Over the course of the past century, the global
automotive industry-s stance towards safety has evolved from one of
contempt to one nearing reverence. A suspension system that
provides safe handling and cornering capabilities can, with the help
of an efficient braking system, improve safety to a large extent. The
aim of this research is to propose a new automotive brake rotor
design and to compare it with automotive vented disk rotor. Static
structural and transient thermal analysis have been carried out on the
vented disk rotor and proposed rotor designs to evaluate and compare
their performance. Finite element analysis was employed for both
static structural and transient thermal analysis. Structural analysis
was carried out to study the stress and deformation pattern of the
rotors under extreme loads. Time varying temperature load was
applied on the rotors and the temperature distribution was analysed
considering cooling parameters (convection and radiation). This
dissertation illustrates the use of Finite Element Methods to examine
models, concluding with a comparative study of the proposed rotor
design and the conventional vented disk rotor for structural stability
and thermal efficiency.
Abstract: In many applications, magnetic suspension systems
are required to operate over large variations in air gap. As a result,
the nonlinearities inherent in most types of suspensions have a
significant impact on performance. Specifically, it may be difficult to
design a linear controller which gives satisfactory performance,
stability, and disturbance rejection over a wide range of operating
points. in this paper an optimal controller based on discontinuous
mathematical model of the system for an electromagnetic suspension
system which is applied in magnetic trains has been designed .
Simulations show that the new controller can adapt well to the
variance of suspension mass and gap, and keep its dynamic
performance, thus it is superior to the classic controller.
Abstract: This paper describes the development, modeling, and
testing of skyhook and MiniMax control strategies of semi-active
suspension. The control performances are investigated using
Matlab/Simulink [1], with a two-degree-of-freedom quarter car semiactive
suspension system model. The comparison and evaluation of
control result are made using software-in-the-loop simulation (SILS)
method. This paper also outlines the development of a hardware-inthe-
loop simulation (HILS) system. The simulation results show that
skyhook strategy can significantly reduce the resonant peak of body
and provide improvement in vehicle ride comfort. Otherwise,
MiniMax strategy can be employed to effectively improve drive
safety of vehicle by influencing wheel load. The two strategies can
be switched to control semi-active suspension system to fulfill
different requirement of vehicle in different stages.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: In this paper, a simple microfluidic device for monitoring algal cell behavior is proposed. An array of algal microwells is fabricated by PDMS soft-lithography using X-ray LIGA mold, placed on a glass substrate. Two layers of replicated PDMS and substrate are attached by oxygen plasma bonding, creating a microchannel for the microfluidic system. Algal cell are loaded into the microfluidic device, which provides positive charge on the bottom surface of wells. Algal cells, which are negative charged, can be attracted to the bottom of the wells via electrostatic interaction. By varying the concentration of algal cells in the loading suspension, it is possible to obtain wells with a single cell. Liquid medium for cells monitoring are flown continuously over the wells, providing nutrient and waste exchange between the well and the main flow. This device could lead to the uncovering of the quantitative biology of the algae, which is a key to effective and extensive algal utilizations in the field of biotechnology, food industry and bioenergy research and developments.
Abstract: The alumosilicate ceramics with mullite crystalline phase are used in various branches of science and technique. The mullite refractory ceramics with high porosity serve as a heat insulator and as a constructional materials [1], [2]. The purpose of the work was to sinter high porosity ceramic and to increase the quantity of mullite phase in this mullite, mullite-corundum ceramics. Two types of compositions were prepared at during the experiment. The first type is compositions with commercial alumina and silica oxides. The second type is from mixing these oxides with 10, 20 and 30 wt.%. of kaolin. In all samples the Al2O3 and SiO2 were in 2.57:1 ratio, because that was conformed to mullite stechiometric compositions (3Al2O3.2SiO2). The types of alumina oxides were α-Al2O3 (d50=4µm) and γ-Al2O3 (d50=80µm). Ratios of α-: γ-Al2O3 were (1:1) or (1:3). The porous materials were prepared by slip casting of suspension of raw materials. The aluminium paste (0.18 wt.%) was used as a pore former. Water content in the suspensions was 26-47 wt.%. Pore formation occurred as a result of hydrogen formation in chemical reaction between aluminium paste and water [2]. The samples were sintered at the temperature of 1650°C and 1750°C for one hour. The increasing amount of kaolin, α-: γ-Al2O3 at the ratio (1:3) and sintering at the highest temperature raised the quantity of mullite phase. The mullite phase began to dominate over the corundum phase.
Abstract: Active vibration isolation systems are less commonly
used than passive systems due to their associated cost and power
requirements. In principle, semi-active isolation systems can deliver
the versatility, adaptability and higher performance of fully active
systems for a fraction of the power consumption. Various semi-active
control algorithms have been suggested in the past. This paper
studies the 4DOF model of semi-active suspension performance
controlled by on–off and continuous skyhook damping control
strategy. The frequency and transient responses of model are
evaluated in terms of body acceleration, roll angle and tire deflection
and are compared with that of a passive damper. The results show
that the semi-active system controlled by skyhook strategy always
provides better isolation than a conventional passively damped
system except at tire natural frequencies.