Abstract: The United Arab Emirates is clearly facing a multitude of challenges in curbing its greenhouse gas emissions to meet its pre-allotted framework of Kyoto protocol and COP21 targets due to its hunger for modernization, industrialization, infrastructure growth, soaring population and oil and gas activity. In this work, we focus on the bonafide zero emission electric vehicles market penetration in the country’s transport industry for emission reduction. We study the global electric vehicle market trends, the complementary battery technologies and the trends by manufacturers, emission standards across borders and prioritized advancements which will ultimately dictate the terms of future conditions for the United Arab Emirate transport industry. Based on our findings and analysis at every stage of current viability and state-of-transport-affairs, we postulate policy recommendations to local governmental entities from a supply and demand perspective covering aspects of technology, infrastructure requirements, change in power dynamics, end user incentives program, market regulators behavior and communications amongst key stakeholders.
Abstract: Thermo-mechanical processing with various processing parameters was applied to 0.2%C-0.6%Mn-2S%i-0.8%Cr low alloyed high strength steel. The aim of the processing was to achieve the microstructures typical for transformation induced plasticity (TRIP) steels. Thermo-mechanical processing used in this work incorporated two or three deformation steps. The deformations were in all the cases carried out during the cooling from soaking temperatures to various bainite hold temperatures. In this way, 4-10% of retained austenite were retained in the final microstructures, consisting further of ferrite, bainite, martensite and pearlite. The complex character of TRIP steel microstructure is responsible for its good strength and ductility. The strengths achieved in this work were in the range of 740 MPa – 836 MPa with ductility A5mm of 31-41%.
Abstract: The purpose of this article is to understand the dynamics of the increase in incivility through social relations (gender, race, class, sexual orientation, etc.), which hide inequalities in the form of treatment and opportunities within the organizational sphere. For this, we will examine works that address incivility at work, as well as studies that deviate from the mainstream, bringing more obscure organizational facets to light in connection with a critical approach to this issue. Next, some results of a bibliometric study shall be exposed, to analyze contributions connected to the theme and demonstrate gaps for future research. Then, models that facilitate reflection on the dynamics of violence shall be discussed. Finally, a broader concept of incivility in interpersonal relationships in the workplace shall be exposed considering the multiple approaches discussed.
Abstract: In this study, Ti-5Al-2.5Fe alloy was prepared by powder metallurgy. The elemental titanium, aluminum, and iron powders were mechanically alloyed for 10 h in a vacuum atmosphere. A stainless steel jar and stainless steel balls were used for mechanical alloying. The alloyed powders were then sintered by vacuum hot pressing at 950 °C for a soaking time of 30 minutes. Pure titanium was also sintered at the same conditions for comparison of mechanical properties and microstructural behavior. The samples were investigated by scanning electron microscopy, XRD analysis, and optical microscopy. Results showed that, after mechanical alloying, a homogeneous distribution of the elements was obtained, and desired a-b structure was determined. Ti-5Al-2.5Fe alloy was successfully produced, and the alloy showed enhanced mechanical properties compared to the commercial pure titanium.
Abstract: The steel contains 0.3% C and 0.004% B, beside Mn, Cr, Mo, and Ni. The alloy was processed by using 20-ton capacity electric arc furnace (EAF), and then refined by ladle furnace (LF). Liquid steel was cast as rectangular ingots. Dilatation test showed the critical transformation temperatures Ac1, Ac3, Ms and Mf as 716, 835, 356, and 218 °C. The ingots were austenitized and soaked and then rough rolled to thin slabs with 80 mm thickness. The thin slabs were then reheated and soaked for finish rolling to 6.0 mm thickness plates. During the rough rolling, the roll force increases as a result of rolling at temperatures less than recrystallization temperature. However, during finish rolling, the steel reflects initially continuous static recrystallization after which it shows strain hardening due to fall of temperature. It was concluded that, the steel plates were successfully heat treated by quenching-tempering at 250 ºC for 20 min.
Abstract: The objective of this article is to improve the passive vibration damping of solar array (SA) used in space structures, by the effective application of numerical optimization. A case study of a SA is used for demonstration. A finite element (FE) model was created and verified by experimental testing. Optimization was then conducted by implementing the FE model with the genetic algorithm, to find the optimal placement of aluminum circular patches, to suppress the first two bending mode shapes. The results were verified using experimental testing. Finally, a parametric study was conducted using the FE model where patch locations, material type, and shape were varied one at a time, and the results were compared with the optimal ones. The results clearly show that through the proper application of FE modeling and numerical optimization, passive vibration damping of space structures has been successfully achieved.
Abstract: Cylindrical alumina microfiltration membrane (GMITM Corporation, inside diameter=9 mm, outside diameter=13 mm, length= 50 mm) with an average pore size of 0.5 micrometer and porosity of about 0.35 was used as the support for membrane reactor. This support was soaked in boehmite sols, and the mean particle size was adjusted in the range of 50 to 500 nm by carefully controlling hydrolysis time, and calcined at 650 °C for two hours. This process was repeated with different boehmite solutions in order to achieve an intermediate layer with an average pore size of about 50 nm. The resulting substrate was then coated with a thin and dense layer of silica by counter current chemical vapour deposition (CVD) method. A boehmite sol with 10 wt.% of nickel which was prepared by a standard procedure was used to make the catalytic layer. BET, SEM, and XRD analysis were used to characterize this layer. The catalytic membrane reactor was placed in an experimental setup to evaluate the permeation and hydrogen separation performance for a steam reforming reaction. The setup consisted of a tubular module in which the membrane was fixed, and the reforming reaction occurred at the inner side of the membrane. Methane stream, diluted with nitrogen, and deionized water with a steam to carbon (S/C) ratio of 3.0 entered the reactor after the reactor was heated up to 500 °C with a specified rate of 2 °C/ min and the catalytic layer was reduced at presence of hydrogen for 2.5 hours. Nitrogen flow was used as sweep gas through the outer side of the reactor. Any liquid produced was trapped and separated at reactor exit by a cold trap, and the produced gases were analyzed by an on-line gas chromatograph (Agilent 7890A) to measure total CH4 conversion and H2 permeation. BET analysis indicated uniform size distribution for catalyst with average pore size of 280 nm and average surface area of 275 m2.g-1. Single-component permeation tests were carried out for hydrogen, methane, and carbon dioxide at temperature range of 500-800 °C, and the results showed almost the same permeance and hydrogen selectivity values for hydrogen as the composite membrane without catalytic layer. Performance of the catalytic membrane was evaluated by applying membranes as a membrane reactor for methane steam reforming reaction at gas hourly space velocity (GHSV) of 10,000 h−1 and 2 bar. CH4 conversion increased from 50% to 85% with increasing reaction temperature from 600 °C to 750 °C, which is sufficiently above equilibrium curve at reaction conditions, but slightly lower than membrane reactor with packed nickel catalytic bed because of its higher surface area compared to the catalytic layer.
Abstract: The aim of information systems integration is to make all the data sources, applications and business flows integrated into the new environment so that unwanted redundancies are reduced and bottlenecks and mismatches are eliminated. Two issues have to be dealt with to meet such requirements: the software architecture that supports resource integration, and the adaptor development tool that help integration and migration of legacy applications. In this paper, a service-enabled dependable integration environment (SDIE), is presented, which has two key components, i.e., a dependable service integration platform and a legacy application integration tool. For the dependable platform for service integration, the service integration bus, the service management framework, the dependable engine for service composition, and the service registry and discovery components are described. For the legacy application integration tool, its basic organization, functionalities and dependable measures taken are presented. Due to its service-oriented integration model, the light-weight extensible container, the service component combination-oriented p-lattice structure, and other features, SDIE has advantages in openness, flexibility, performance-price ratio and feature support over commercial products, is better than most of the open source integration software in functionality, performance and dependability support.
Abstract: One of the key solutions to the climate change crisis is to develop renewable energy resources, such as solar and wind power and biogas. This paper explores the socioeconomic and environmental viability of solar energy, based on a case study of the Soan Valley Development Program. Under this project, local farmers were provided solar water pumps at subsidized rates. These have been functional for the last seven years and have gained popularity among the local communities. The study measures the economic viability of using solar energy in agriculture, based on data from 36 households, of which 12 households each use diesel, electric and solar water pumps. Our findings are based on the net present value of each technology type. We also carry out a qualitative assessment of the social impact of solar water pumps relative to diesel and electric pumps. Finally, we conduct an environmental impact assessment, using the lifecycle assessment approach. All three analyses indicate that solar energy is a viable alternative to diesel and electricity.
Abstract: Reverse osmosis (RO) membranes have been widely used for desalination to purify water for drinking and other purposes. Although at present most RO membranes have no resistance to chlorine, chlorine-resistant membranes are being developed. Therefore, direct chlorine treatment or chlorine washing will be an option in preventing biofouling on chlorine-resistant membranes. Furthermore, if particle accumulation control is possible by using chlorine washing, expensive pretreatment for particle removal can be removed or simplified. The objective of this study was to determine the effective hypochlorite washing condition required for controlling biofilm formation and inorganic particle accumulation on RO membrane in a continuous flow channel with RO membrane and spacer. In this study, direct chlorine washing was done by soaking fouled RO membranes in hypochlorite solution and fluorescence intensity was used to quantify biofilm on the membrane surface. After 48 h of soaking the membranes in high fouling potential waters, the fluorescence intensity decreased to 0 from 470 using the following washing conditions: 10 mg/L chlorine concentration, 2 times/d washing interval, and 30 min washing time. The chlorine concentration required to control biofilm formation decreased as the chlorine concentration (0.5–10 mg/L), the washing interval (1–4 times/d), or the washing time (1–30 min) increased. For the sample solutions used in the study, 10 mg/L chlorine concentration with 2 times/d interval, and 5 min washing time was required for biofilm control. The optimum chlorine washing conditions obtained from soaking experiments proved to be applicable also in controlling biofilm formation in continuous flow experiments. Moreover, chlorine washing employed in controlling biofilm with suspended particles resulted in lower amounts of organic (0.03 mg/cm2) and inorganic (0.14 mg/cm2) deposits on the membrane than that for sample water without chlorine washing (0.14 mg/cm2 and 0.33 mg/cm2, respectively). The amount of biofilm formed was 79% controlled by continuous washing with 10 mg/L of free chlorine concentration, and the inorganic accumulation amount decreased by 58% to levels similar to that of pure water with kaolin (0.17 mg/cm2) as feed water. These results confirmed the acceleration of particle accumulation due to biofilm formation, and that the inhibition of biofilm growth can almost completely reduce further particle accumulation. In addition, effective hypochlorite washing condition which can control both biofilm formation and particle accumulation could be achieved.
Abstract: This paper aims to assess the efficiency of using geogrid reinforcement for subgrade stabilization. The literature of applying geogrid reinforcement technique for pavements built on soft subgrades and the previous experiences were reviewed. Laboratory tests were conducted on soil reinforced with geogrids in one or several layers. The soil specimens were compacted in four layers with or without geogrid sheets. The California Bearing Ratio (CBR) test, in soaking condition, was performed on natural soil and soil-geogrid specimens. The test results revealed that the CBR value is much affected by the geogrid sheet location and the number of sheets used in the soil specimen. When a geogrid sheet was placed at the 1st layer of the soil, there was an increment of 26% in the CBR value. Moreover, the CBR value was significantly increased by 62% when geogrid sheets were placed at all four layers. The high CBR value is attributed to interface friction and interlock involved in the geogrid/ soil interactions. It could be concluded that geogrid reinforcement is successful and more economical technique.
Abstract: The collapse of the infamous Rana Plaza, a multi-storeyed commercial building in Savar, near Dhaka, Bangladesh has brought with it a plethora of positive and negative consequences. Bangladesh being a key player in the export of clothing, found itself amidst a wave of economic upheaval following this tragic incident that resulted in numerous Bangladeshis, most of whom were factory workers. This paper compares the consequences that the country’s Ready Made Garments (RMG) sector is facing now, two years into the incident. The paper presents a comparison of statistical data from study reports and brings forward perspectives from all dimensions of Labour, Employment and Industrial Relations in Bangladesh following the event. The paper brings across the viewpoint of donor organizations and donor countries, the impacts of several initiatives taken by foreign organizations like the International Labour Organization, and local entities like the Bangladesh Garment Manufacturers and Exporters Association (BGMEA) in order to reinforce compliance and stabilize the shaky foundation that the RMG sector had found itself following the collapse. Focus of the paper remains on the stance taken by the suppliers in Bangladesh, with inputs from buying houses and factories, and also on the reaction of foreign brands. The paper also focuses on the horrific physical, mental and financial implications sustained by the victims and their families, and the consequent uproar from workers in general regarding compliance with work safety and workers’ welfare conditions. The purpose is to get across both sides of the scenario: the economic impact that suppliers / factories/ sellers/ buying houses/exporters have faced in Bangladesh as a result of complete loss of reliability on them regarding working standards; and also to cover the aftershock felt on the other end of the spectrum by the importers/ buyers, particularly the foreign entities, in terms of the sudden accountability of being affiliated with non- compliant factories. The collapse of Rana Plaza has received vast international attention and strong criticism. Nevertheless, the almost immediate strengthening of labourrights and the wholesale reform undertaken on all sides of the supply chain, evidence a move of all local and foreign stakeholders towards greater compliance and taking of precautionary steps for prevention of further disasters. The tragedy that Rana Plaza embodies served as a much-needed epiphany for the soaring RMG Sector of Bangladesh. Prompt co-operation on the part of all stakeholders and regulatory bodies now show a move towards sustainable development, which further ensures safeguarding against any future irregularities and pave the way for steady economic growth.
Abstract: Among other traditional and non-traditional
additives, polymers have shown an efficient performance in the field
and improved sustainability. Polyacrylamide (PAM) is one such
additive that has demonstrated many advantages including a
reduction in permeability, an increase in durability and the provision
of strength characteristics. However, information about its effect on
the improved geotechnical characteristics is very limited to the field
performance monitoring. Therefore, a laboratory investigation was
carried out to examine the basic and engineering behaviors of three
types of soils treated with a PAM additive. The results showed an
increase in dry density and unconfined compressive strength for all
the soils. The results further demonstrated an increase in unsoaked
CBR and a reduction in permeability for all stabilized samples.
Abstract: The increasing availability of information about earth
surface elevation (Digital Elevation Models DEM) generated from
different sources (remote sensing, Aerial Images, Lidar) poses the
question about how to integrate and make available to the most than
possible audience this huge amount of data. In order to exploit the potential of 3D elevation representation the
quality of data management plays a fundamental role. Due to the high
acquisition costs and the huge amount of generated data, highresolution
terrain surveys tend to be small or medium sized and
available on limited portion of earth. Here comes the need to merge
large-scale height maps that typically are made available for free at
worldwide level, with very specific high resolute datasets. One the
other hand, the third dimension increases the user experience and the
data representation quality, unlocking new possibilities in data
analysis for civil protection, real estate, urban planning, environment
monitoring, etc. The open-source 3D virtual globes, which are
trending topics in Geovisual Analytics, aim at improving the
visualization of geographical data provided by standard web services
or with proprietary formats. Typically, 3D Virtual globes like do not
offer an open-source tool that allows the generation of a terrain
elevation data structure starting from heterogeneous-resolution terrain
datasets. This paper describes a technological solution aimed to set
up a so-called “Terrain Builder”. This tool is able to merge
heterogeneous-resolution datasets, and to provide a multi-resolution
worldwide terrain services fully compatible with CesiumJS and
therefore accessible via web using traditional browser without any
additional plug-in.
Abstract: In this corporate world, the technology of Web
services has grown rapidly and its significance for the development
of web based applications gradually rises over time. The success of
Business to Business integration rely on finding novel partners and
their services in a global business environment. However, the
selection of the most suitable Web service from the list of services
with the identical functionality is more vital. The satisfaction level of
the customer and the provider’s reputation of the Web service are
primarily depending on the range it reaches the customer’s
requirements. In most cases, the customer of the Web service feels
that he is spending for the service which is undelivered. This is
because the customer always thinks that the real functionality of the
web service is not reached. This will lead to change of the service
frequently. In this paper, a framework is proposed to evaluate the
Quality of Service (QoS) and its cost that makes the optimal
correlation between each other. In addition, this research work
proposes some management decision against the functional deviancy
of the web service that is guaranteed at time of selection.
Abstract: The main cause of Alzheimer disease (AD) was
believed to be mainly due to the accumulation of free radicals owing
to oxidative stress (OS) in brain tissue. The mechanism of the
neurotoxicity of Aluminum chloride (AlCl3) induced AD in
hippocampus Albino wister rat brain tissue, the curative & the
protective effects of Lipidium sativum group (LS) water extract were
assessed after 8 weeks by attenuated total reflection spectroscopy
ATR-IR and histologically by light microscope. ATR-IR results
revealed that the membrane phospholipid undergo free radical
attacks, mediated by AlCl3, primary affects the polyunsaturated fatty
acids indicated by the increased of the olefinic -C=CH sub-band area
around 3012 cm-1 from the curve fitting analysis. The narrowing in
the half band width (HBW) of the sνCH2 sub-band around 2852 cm-1
due to Al intoxication indicates the presence of trans form fatty acids
rather than gauch rotomer. The degradation of hydrocarbon chain to
shorter chain length, increasing in membrane fluidity, disorder, and
decreasing in lipid polarity in AlCl3 group indicated by the detected
changes in certain calculated area ratios compared to the control.
Administration of LS was greatly improved these parameters
compared to the AlCl3 group. Al influences the Aβ aggregation and
plaque formation, which in turn interferes to and disrupts the
membrane structure. The results also showed a marked increase in
the β-parallel and antiparallel structure, that characterize the Aβ
formation in Al-induced AD hippocampal brain tissue, indicated by
the detected increase in both amide I sub-bands around 1674, 1692
cm-1. This drastic increase in Aβ formation was greatly reduced in the
curative and protective groups compared to the AlCl3 group and
approached nearly the control values. These results supported too by
the light microscope. AlCl3 group showed significant marked
degenerative changes in hippocampal neurons. Most cells appeared
small, shrieked and deformed. Interestingly, the administration of LS
in curative and protective groups markedly decreases the amount of
degenerated cells compared to the non-treated group. In addition, the
intensity of congo red stained cells was decreased. Hippocampal
neurons looked more/or less similar to those of control. This study showed a promising therapeutic effect of Lipidium
sativum group (LS) on AD rat model that seriously overcome the
signs of oxidative stress on membrane lipid and restore the protein
misfolding.
Abstract: Modelling of building processes of a multimodal
freight transportation support information system is discussed based
on modern CASE technologies. Functional efficiencies of ports in
the eastern part of the Black Sea are analyzed taking into account
their ecological, seasonal, resource usage parameters. By resources,
we mean capacities of berths, cranes, automotive transport, as well as
work crews and neighbouring airports. For the purpose of designing
database of computer support system for Managerial (Logistics)
function, using Object-Role Modeling (ORM) tool (NORMA–Natural ORM Architecture) is proposed, after which Entity
Relationship Model (ERM) is generated in automated process.
Software is developed based on Process-Oriented and Service-Oriented architecture, in Visual Studio.NET environment.
Abstract: A new design of aerostatic thrust bearing is proposed
for high static stiffness. The bearing body, which is mead of polymer
covered with metallic membrane, is held by a circular ring. Such a
support helps form a concave air gap to grasp the air pressure. The
polymer body, which can be made rapidly by either injection or
molding is able to provide extra damping under dynamic loading. The
smooth membrane not only serves as the bearing surface but also
protects the polymer body. The restrictor is a capillary inside a silicone
tube. It can passively compensate the variation of load by expanding
the capillary diameter for more air flux. In the present example, the
stiffness soars from 15.85 N/μm of typical bearing to 349.85 N/μm at
bearing elevation 9.5 μm; meanwhile the load capacity also enhances
from 346.86 N to 704.18 N.
Abstract: Cadmium (II) (Cd) is one of the major toxic elemental
pollutants, which is hazardous for humans, animals and plants. γ-
Polyglutamic acid (γ-PGA) is an extracellular biopolymer produced
by several species of Bacillus which has been reported to be an
effective biosorbent for metal ions. The effect of γ-PGA on growth of
rice grown under laboratory conditions was investigated. Rice seeds
were germinated and then grown at 30±1°C on filter paper soaked
with Cd solution and γ-PGA for 7 days. The result showed that Cd
significantly inhibited the growth of roots, shoots by reducing root,
and shoot lengths. Fresh and dry weights also decreased compared
with control; however, the addition of 500 mg·L-1 γ-PGA alleviated
rice seedlings from the adverse effects of Cd. The analysis of
physiological traits revealed that Cd caused a decrease in the total
chlorophyll and soluble protein contents and amylase activities in all
treatments. The Cd content in seedling tissues increased for the Cd
250 μM treatment (P
Abstract: Cross-linked konjac glucomannan and kappa
carrageenan film were prepared by chemical crosslinking using
glutaraldehyde (GA) as the crosslinking agent. The effect
crosslinking on the swelling degree was investigated. Konjac
glucomannan and its mixture with kappa carrageenan film was
immersed in GA solution and then thermally cured. The obtained
cross-linked film was washed and soaked in the ethanol to remove
the unreacted GA. The obtained film was air dried at room
temperature to a constant weight. The infrared spectra and the value
of swelling degree of obtained crosslinked film showed that
glucomannan and kappa carrageenan was able to be cross-linked
using glutaraldehyde by film immersion and curing method without
catalyst. The cross-linked films were found to be pH sensitive,
indicating a potential to be used in drug delivery polymer system.