Abstract: In this research, heat transfer of a poly Ethylene
fluidized bed reactor without reaction were studied experimentally
and computationally at different superficial gas velocities. A multifluid
Eulerian computational model incorporating the kinetic theory
for solid particles was developed and used to simulate the heat
conducting gas–solid flows in a fluidized bed configuration.
Momentum exchange coefficients were evaluated using the Syamlal–
O-Brien drag functions. Temperature distributions of different phases
in the reactor were also computed. Good agreement was found
between the model predictions and the experimentally obtained data
for the bed expansion ratio as well as the qualitative gas–solid flow
patterns. The simulation and experimental results showed that the gas
temperature decreases as it moves upward in the reactor, while the
solid particle temperature increases. Pressure drop and temperature
distribution predicted by the simulations were in good agreement
with the experimental measurements at superficial gas velocities
higher than the minimum fluidization velocity. Also, the predicted
time-average local voidage profiles were in reasonable agreement
with the experimental results. The study showed that the
computational model was capable of predicting the heat transfer and
the hydrodynamic behavior of gas-solid fluidized bed flows with
reasonable accuracy.
Abstract: This paper proposes a methodology for analysis of
the dynamic behavior of a robotic manipulator in continuous
time. Initially this system (nonlinear system) will be decomposed
into linear submodels and analyzed in the context of the Linear
and Parameter Varying (LPV) Systems. The obtained linear
submodels, which represent the local dynamic behavior of the
robotic manipulator in some operating points were grouped in
a Takagi-Sugeno fuzzy structure. The obtained fuzzy model was
analyzed and validated through analog simulation, as universal
approximator of the robotic manipulator.
Abstract: This paper proposes a method to vibration analysis in
order to on-line monitoring and predictive maintenance during the
milling process. Adapting envelope method to diagnostics and the
analysis for milling tool materials is an important contribution to the
qualitative and quantitative characterization of milling capacity and a
step by modeling the three-dimensional cutting process. An
experimental protocol was designed and developed for the
acquisition, processing and analyzing three-dimensional signal. The
vibration envelope analysis is proposed to detect the cutting capacity
of the tool with the optimization application of cutting parameters.
The research is focused on Hilbert transform optimization to evaluate
the dynamic behavior of the machine/ tool/workpiece.
Abstract: Real-time embedded systems should benefit from
component-based software engineering to handle complexity and
deal with dependability. In these systems, applications should not
only be logically correct but also behave within time windows.
However, in the current component based software engineering
approaches, a few of component models handles time properties in
a manner that allows efficient analysis and checking at the
architectural level. In this paper, we present a meta-model for
component-based software description that integrates timing
issues. To achieve a complete functional model of software
components, our meta-model focuses on four functional aspects:
interface, static behavior, dynamic behavior, and interaction
protocol. With each aspect we have explicitly associated a time
model. Such a time model can be used to check a component-s
design against certain properties and to compute the timing
properties of component assemblies.
Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: The paper presents the virtual model of the active
suspension system used for improving the dynamic behavior of a
motor vehicle. The study is focused on the design of the control
system, the purpose being to minimize the effect of the road
disturbances (which are considered as perturbations for the control
system). The analysis is performed for a quarter-car model, which
corresponds to the suspension system of the front wheel, by using the
DFC (Design for Control) software solution EASY5 (Engineering
Analysis Systems) of MSC Software. The controller, which is a PIDbased
device, is designed through a parametric optimization with the
Matrix Algebra Tool (MAT), considering the gain factors as design
variables, while the design objective is to minimize the overshoot of
the indicial response.
Abstract: Micro droplet formation is considered as a growing
emerging area of research due to its wide-range application in
chemistry as well as biology. The mechanism of micro droplet
formation using two immiscible liquids running through a T-junction
has been widely studied.
We believe that the flow of these two immiscible phases can be of
greater important factor that could have an impact on out-flow
hydrodynamic behavior, the droplets generated and the size of the
droplets. In this study, the type of the capillary tubes used also
represents another important factor that can have an impact on the
generation of micro droplets.
The tygon capillary tubing with hydrophilic inner surface doesn't
allow regular out-flows due to the fact that the continuous phase
doesn't adhere to the wall of the capillary inner surface.
Teflon capillary tubing, presents better wettability than tygon
tubing, and allows to obtain steady and regular regimes of out-flow,
and the micro droplets are homogeneoussize.
The size of the droplets is directly dependent on the flows of the
continuous and dispersed phases. Thus, as increasing the flow of the
continuous phase, to flow of the dispersed phase stationary, the size
of the drops decreases. Inversely, while increasing the flow of the
dispersed phase, to flow of the continuous phase stationary, the size
of the droplet increases.
Abstract: Complexity, as a theoretical background has made it
easier to understand and explain the features and dynamic behavior
of various complex systems. As the common theoretical background
has confirmed, borrowing the terminology for design from the
natural sciences has helped to control and understand urban
complexity. Phenomena like self-organization, evolution and
adaptation are appropriate to describe the formerly inaccessible
characteristics of the complex environment in unpredictable bottomup
systems. Increased computing capacity has been a key element in
capturing the chaotic nature of these systems.
A paradigm shift in urban planning and architectural design has
forced us to give up the illusion of total control in urban
environment, and consequently to seek for novel methods for
steering the development. New methods using dynamic modeling
have offered a real option for more thorough understanding of
complexity and urban processes. At best new approaches may renew
the design processes so that we get a better grip on the complex
world via more flexible processes, support urban environmental
diversity and respond to our needs beyond basic welfare by liberating
ourselves from the standardized minimalism.
A complex system and its features are as such beyond human
ethics. Self-organization or evolution is either good or bad. Their
mechanisms are by nature devoid of reason. They are common in
urban dynamics in both natural processes and gas. They are features
of a complex system, and they cannot be prevented. Yet their
dynamics can be studied and supported.
The paradigm of complexity and new design approaches has been
criticized for a lack of humanity and morality, but the ethical
implications of scientific or computational design processes have not
been much discussed. It is important to distinguish the (unexciting)
ethics of the theory and tools from the ethics of computer aided
processes based on ethical decisions. Urban planning and architecture
cannot be based on the survival of the fittest; however, the natural
dynamics of the system cannot be impeded on grounds of being
“non-human".
In this paper the ethical challenges of using the dynamic models
are contemplated in light of a few examples of new architecture and
dynamic urban models and literature. It is suggested that ethical
challenges in computational design processes could be reframed
under the concepts of responsibility and transparency.
Abstract: Bioprocesses are appreciated as difficult to control because their dynamic behavior is highly nonlinear and time varying, in particular, when they are operating in fed batch mode. The research objective of this study was to develop an appropriate control method for a complex bioprocess and to implement it on a laboratory plant. Hence, an intelligent control structure has been designed in order to produce biomass and to maximize the specific growth rate.
Abstract: Water recycling represents an important challenge for many countries, in particular in countries where this natural resource is rare. On the other hand, in many operations, water is used as a cooling medium, as a high proportion of water consumed in industry is used for cooling purposes. Generally this water is rejected directly to the nature. This reject will cause serious environment damages as well as an important waste of this precious element.. On way to solve these problems is to reuse and recycle this warm water, through the use of natural cooling medium, such as air in a heat exchanger unit, known as a cooling tower. A poor performance, design or reliability of cooling towers will result in lower flow rate of cooling water an increase in the evaporation of water, an hence losses of water and energy. This paper which presents an experimental investigate of thermal and hydraulic performances of a mechanical cooling tower, enables to show that the water evaporation rate, Mev, increases with an increase in the air and water flow rates, as well as inlet water temperature and for fixed air flow rates, the pressure drop (ΔPw/Z) increases with increasing , L, due to the hydrodynamic behavior of the air/water flow.
Abstract: An immunomodulator bioproduct is prepared in a
batch bioprocess with a modified bacterium Pseudomonas
aeruginosa. The bioprocess is performed in 100 L Bioengineering
bioreactor with 42 L cultivation medium made of peptone, meat
extract and sodium chloride. The optimal bioprocess parameters were
determined: temperature – 37 0C, agitation speed - 300 rpm, aeration
rate – 40 L/min, pressure – 0.5 bar, Dow Corning Antifoam M-max.
4 % of the medium volume, duration - 6 hours. This kind of
bioprocesses are appreciated as difficult to control because their
dynamic behavior is highly nonlinear and time varying. The aim of
the paper is to present (by comparison) different models based on
experimental data.
The analysis criteria were modeling error and convergence rate.
The estimated values and the modeling analysis were done by using
the Table Curve 2D.
The preliminary conclusions indicate Andrews-s model with a
maximum specific growth rate of the bacterium in the range of
0.8 h-1.
Abstract: The so-called all-pass filter circuits are commonly
used in the field of signal processing, control and measurement.
Being connected to capacitive loads, these circuits tend to loose their
stability; therefore the elaborate analysis of their dynamic behavior is
necessary. The compensation methods intending to increase the
stability of such circuits are discussed in this paper, including the socalled
lead-lag compensation technique being treated in detail. For
the dynamic modeling, a two-port network model of the all-pass filter
is being derived. The results of the model analysis show, that
effective lead-lag compensation can be achieved, alone by the
optimization of the circuit parameters; therefore the application of
additional electric components are not needed to fulfill the stability
requirement.
Abstract: The transient hydrodynamics and thermal behaviors of
fluid flow in open-ended vertical parallel-plate porous microchannel are investigated semi-analytically under the effect of the hyperbolic
heat conduction model. The model that combines both the continuum approach and the possibility of slip at the boundary is adopted in the
study. The Effects of Knudsen number , Darcy number , and thermal relaxation time on the microchannel hydrodynamics and thermal behaviors are investigated using the hyperbolic heat
conduction models. It is found that as increases the slip in the hydrodynamic and thermal boundary condition increases. This slip in
the hydrodynamic boundary condition increases as increases. Also, the slip in the thermal boundary condition increases as
decreases especially the early stage of time.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.
Abstract: Saccharomyces cerevisiae (baker-s yeast) can exhibit
sustained oscillations during the operation in a continuous bioreactor
that adversely affects its stability and productivity. Because of
heterogeneous nature of cell populations, the cell population balance
models can be used to capture the dynamic behavior of such cultures.
In this paper an unstructured, segregated model is used which is
based on population balance equation(PBE) and then in order to
simulation, the 4th order Rung-Kutta is used for time dimension and
three methods, finite difference, orthogonal collocation on finite
elements and Galerkin finite element are used for discretization of the
cell mass domain. The results indicate that the orthogonal collocation
on finite element not only is able to predict the oscillating behavior of
the cell culture but also needs much little time for calculations.
Therefore this method is preferred in comparison with other methods.
In the next step two controllers, a globally linearizing control (GLC)
and a conventional proportional-integral (PI) controller are designed
for controlling the total cell mass per unit volume, and performances
of these controllers are compared through simulation. The results
show that although the PI controller has simpler structure, the GLC
has better performance.
Abstract: This paper details few mechanical modeling and
design issues of RF MEMS switches. We concentrate on an
electrostatically actuated broad side series switch; surface
micromachined with a crab leg membrane. The same results are
extended to any complex structure. With available experimental data
and fabrication results, we present the variation in dynamic
performance and compliance of the switch with reference to few
design issues, which we find are critical in deciding the dynamic
behavior of the switch, without compromise on the RF
characteristics. The optimization of pull in voltage, transient time and
resonant frequency with regard to these critical design parameters are
also presented.
Abstract: This paper presents a novel methodology for Maximum Power Point Tracking (MPPT) of a grid-connected 20 kW Photovoltaic (PV) system using neuro-fuzzy network. The proposed method predicts the reference PV voltage guarantying optimal power transfer between the PV generator and the main utility grid. The neuro-fuzzy network is composed of a fuzzy rule-based classifier and three Radial Basis Function Neural Networks (RBFNN). Inputs of the network (irradiance and temperature) are classified before they are fed into the appropriated RBFNN for either training or estimation process while the output is the reference voltage. The main advantage of the proposed methodology, comparing to a conventional single neural network-based approach, is the distinct generalization ability regarding to the nonlinear and dynamic behavior of a PV generator. In fact, the neuro-fuzzy network is a neural network based multi-model machine learning that defines a set of local models emulating the complex and non-linear behavior of a PV generator under a wide range of operating conditions. Simulation results under several rapid irradiance variations proved that the proposed MPPT method fulfilled the highest efficiency comparing to a conventional single neural network.
Abstract: Gas condensate Reservoirs show complicated thermodynamic behavior when their pressure reduces to under dew point pressure. Condensate blockage around the producing well cause significant reduction of production rate as well bottom-hole pressure drops below saturation pressure. The main objective of this work was to examine the well test analysis of naturally fractured lean gas condensate reservoir and investigate the effect of condensate formed around the well-bore on behavior of single phase pseudo pressure and its derivative curves. In this work a naturally fractured lean gas condensate reservoir is simulated with compositional simulator. Different sensitivity analysis done on Corry parameters and result of simulator is feed to analytical well testing software. For consideration of these phenomena eighteen compositional models with Capillary number effect are constructed. Matrix relative permeability obeys Corry relative permeability and relative permeability in fracture is linear. Well testing behavior of these models are studied and interpreted. Results show different sensitivity analysis on relative permeability of matrix does not have strong effect on well testing behavior even most part of the matrix around the well is occupied with condensate.
Abstract: Modeling of the dynamic behavior and motion are
renewed interest in the improved tractive performance of an
intelligent air-cushion tracked vehicle (IACTV). This paper presents
a new dynamical model for the forces on the developed small scale
intelligent air-cushion tracked vehicle moving over swamp peat. The
air cushion system partially supports the 25 % of vehicle total weight
in order to make the vehicle ground contact pressure 7 kN/m2. As the
air-cushion support system can adjust automatically on the terrain, so
the vehicle can move over the terrain without any risks. The springdamper
system is used with the vehicle body to control the aircushion
support system on any undulating terrain by making the
system sinusoidal form. Experiments have been carried out to
investigate the relationships among tractive efficiency, slippage,
traction coefficient, load distribution ratio, tractive effort, motion
resistance and power consumption in given terrain conditions.
Experiment and simulation results show that air-cushion system
improves the vehicle performance by keeping traction coefficient of
71% and tractive efficiency of 62% and the developed model can
meet the demand of transport efficiency with the optimal power
consumption.
Abstract: Considering non-ideal behavior of fluids and its effects on hydrodynamic and mass transfer in multiphase flow is very essential. Simulations were performed that takes into account the effects of mass transfer and mixture non-ideality on hydrodynamics reported by Irani et al. In this paper, by assuming the density of phases to be constant and Raullt-s law instead of using EOS and fugacity coefficient definition, respectively for both the liquid and gas phases, the importance of non-ideality effects on mass transfer and hydrodynamic behavior was studied. The results for a system of octane/propane (T=323 K, P =445 kpa) also indicated that the assumption of constant density in simulation had major role to diverse from experimental data. Furthermore, comparison between obtained results and the previous report indicated significant differences between experimental data and simulation results with more ideal assumptions.