Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: The use of bioindicators plants (lichens, bryophytes
and Sphagnum....) in monitoring pollution by heavy metals has been
the subject of several works. However, few studies have addressed
the impact of specific type-s pollutants (fertilizers, pesticides.) on
these organisms.
We propose in this work to make the highlighting effect of NPKs
(NPK: nitrogen-phosphate-potassium-sulfate (NP2O5K2O) (15,15,15),
at concentrations of 10, 20, 30 , 40 and 50mM/L) on the activity of
detoxification enzymes (GSH/GST, CAT, APX and MDA) of plant
bioindicators (mosses and lichens) after treatment for 3 and 7 days.
This study shows the important role of the defense system in the
accumulation and tolerance to chemical pollutants through the
activation of enzymatic (GST (glutathione-S-transferase, APX
(ascorbat peroxidase), CAT (catalase)) and nonenzymatic biomarkers
(GSH (glutathione), MDA (malondialdehyde)) against oxidative
stress generated by the NPKs.
Abstract: Recently, a great amount of interest has been shown
in the field of modeling and controlling hybrid systems. One of the
efficient and common methods in this area utilizes the mixed logicaldynamical
(MLD) systems in the modeling. In this method, the
system constraints are transformed into mixed-integer inequalities by
defining some logic statements. In this paper, a system containing
three tanks is modeled as a nonlinear switched system by using the
MLD framework. Comparing the model size of the three-tank system
with that of a two-tank system, it is deduced that the number of
binary variables, the size of the system and its complexity
tremendously increases with the number of tanks, which makes the
control of the system more difficult. Therefore, methods should be
found which result in fewer mixed-integer inequalities.
Abstract: The Comparison analysis of the Wald-s and Bayestype sequential methods for testing hypotheses is offered. The merits of the new sequential test are: universality which consists in optimality (with given criteria) and uniformity of decision-making regions for any number of hypotheses; simplicity, convenience and uniformity of the algorithms of their realization; reliability of the obtained results and an opportunity of providing the errors probabilities of desirable values. There are given the Computation results of concrete examples which confirm the above-stated characteristics of the new method and characterize the considered methods in regard to each other.
Abstract: In this paper, an analytical modeling is presentated to
describe the channel noise in GME SGT/CGT MOSFET, based on
explicit functions of MOSFETs geometry and biasing conditions for
all channel length down to deep submicron and is verified with the
experimental data. Results shows the impact of various parameters
such as gate bias, drain bias, channel length ,device diameter and gate
material work function difference on drain current noise spectral
density of the device reflecting its applicability for circuit design
applications.
Abstract: Particle boards were prepared from Maize cob (MC) and urea-formaldehyde resin (UFR) on compression moulding machine. The amount of MC was varied from 50-120g while 30g of UFR was kept constant. Some mechanical properties of the particle boards were tested using the standard ASM methods. The results show that as the MC content increased from 50- 120g in 30g UFR, the hardness increased from about 6.89 x 102 to7.51 x 102MPa. Impact strength decreased from 3.3x 10-2 to 0.45 x 10-2J/M2, while tensile strength initially increased from 2.63 x 102 to 3.14 x 102 MPa as the MC increased from 50 to 60g in 30g UFR, thereafter, it decreased to about 1.35 x 102MPa at 120g in 30g content.
Abstract: Inverse kinematics analysis plays an important role in developing a robot manipulator. But it is not too easy to derive the inverse kinematic equation of a robot manipulator especially robot manipulator which has numerous degree of freedom. This paper describes an application of Artificial Neural Network for modeling the inverse kinematics equation of a robot manipulator. In this case, the robot has three degree of freedoms and the robot was implemented for drilling a printed circuit board. The artificial neural network architecture used for modeling is a multilayer perceptron networks with steepest descent backpropagation training algorithm. The designed artificial neural network has 2 inputs, 2 outputs and varies in number of hidden layer. Experiments were done in variation of number of hidden layer and learning rate. Experimental results show that the best architecture of artificial neural network used for modeling inverse kinematics of is multilayer perceptron with 1 hidden layer and 38 neurons per hidden layer. This network resulted a RMSE value of 0.01474.
Abstract: In July 2012, an indoor/outdoor monitoring
programme was undertaken in two university sports facilities: a
fronton and a gymnasium. Comfort parameters (temperature, relative
humidity, CO and CO2) and total volatile organic compounds
(VOCs) were continuously monitored. Concentrations of NO2,
carbonyl compounds and individual VOCs were obtained. Low
volume samplers were used to collect particulate matter (PM10). The
minimum ventilation rates stipulated for acceptable indoor air quality
were observed in both sports facilities. It was found that cleaning
activities may have a large influence on the VOC levels. Acrolein
was one of the most abundant carbonyl compounds, showing
concentrations above the recommended limit. Formaldehyde was
detected at levels lower than those commonly reported for other
indoor environments. The PM10 concentrations obtained during the
occupancy periods ranged between 38 and 43μgm-3 in the fronton and
from 154 to 198μgm-3 in the gymnasium.
Abstract: This paper presents a new sensor-based online method for generating collision-free near-optimal paths for mobile robots pursuing a moving target amidst dynamic and static obstacles. At each iteration, first the set of all collision-free directions are calculated using velocity vectors of the robot relative to each obstacle and target, forming the Directive Circle (DC), which is a novel concept. Then, a direction close to the shortest path to the target is selected from feasible directions in DC. The DC prevents the robot from being trapped in deadlocks or local minima. It is assumed that the target's velocity is known, while the speeds of dynamic obstacles, as well as the locations of static obstacles, are to be calculated online. Extensive simulations and experimental results demonstrated the efficiency of the proposed method and its success in coping with complex environments and obstacles.
Abstract: In this study, the powders of Ni and Ti with 50.5 at.%
Ni for 12 h were blended and cold pressed at the different pressures
(50, 75 and100 MPa).The porous product obtained after Ni-Ti
compacts were synthesized by SHS (self-propagating hightemperature
synthesis) in the different preheating temperatures (200,
250 and 300oC) and heating rates (30, 60 and 90oC/min). The effects
of the pressure, preheating temperature and heating rate were
investigated on biocompatibility in vivo. The porosity in the
synthesized products was in the range of 50.7–59.7 vol. %. The
pressure, preheating temperature and heating rate were found to have
an important effect on the biocompatibility in-vivo of the synthesized
products. Max. fibrotic tissue within the porous implant was found in
vivo periods (6 months), in which compacting pressure 100MPa.
Abstract: The liberalization and privatization processes have
forced public utility companies to face new competitive challenges,
implementing strategies to gain market share and, at the same time,
keep the old customers. To this end, many companies have carried
out mergers, acquisitions and conglomerations in order to diversify
their business. This paper focuses on companies operating in the free
energy market in Italy. In the last decade, this sector has undergone
profound changes that have radically changed the competitive
scenario and have led companies to implement diversification
strategies of the business. Our work aims to evaluate the economic
and financial performances obtained by energy companies, following
the beginning of the liberalization process, verifying the possible
relationship with the implemented diversification strategies.
Abstract: Uterine and oviducal fluids are necessary for
capacitation of the spermatozoa and early embryonic development.
The aim of the present study was to determine the effects of estrous
cycle phases (follicular and luteal) on some biological parameters
(enzymes, electrolytes and total proteins) in uterine and oviducal
secretions of ewes. Oviducal and uterine fluids were collected,
diluted and centrifuged. According to our results, concentrations of
GPT, G6PDH, total proteins, K and Na were significantly (P
Abstract: Optimization study of the diesters biolubricant oleyl 9(12)-hydroxy-10(13)-oleioxy-12(9)-octadecanoate (OLHYOOT) was synthesized in the presence of sulfuric acid (SA) as catalyst has been done. Optimum conditions of the experiment to obtain high yield% of OLHYOOT were predicted at ratio of OL/HYOOA of 1:1 g/g, ratio of SA/HYOOA of 0.20:1 g/g, reaction temperature 110 °C and 4.5 h of reaction time. At this condition, the Yield% of OLHYOOT was 88.7. Disappearance of carboxylic acid (C=O) peak has observed by FTIR with appearance ester (C=O) at 1738 cm-1. 1H NMR spectra analyses confirmed the result of OLHYOOT with appearance ester (-CHOCOR) at 4.05ppm and also the 13C-NMR confirmed the result with appearance ester (C=O) peak at 173.93ppm.
Abstract: Today, cancer remains one of the major diseases that
lead to death. The main obstacle in chemotherapy as a main cancer
treatment is the toxicity to normal cells due to Multidrug Resistance
(MDR) after the use of anticancer drugs. Proposed solution to
overcome this problem is the use of MDR efflux inhibitor of cinchona
alkaloids which is delivered together with anticancer drugs
encapsulated in the form of polymeric nanoparticles. The particles
were prepared by the hydration method. The characterization of
nanoparticles was particle size, zeta potential, entrapment efficiency
and in vitro drug release. Combination nanoparticle size ranged 29-45
nm with a neutral surface charge. Entrapment efficiency was above
87% for the use quinine, quinidine or cinchonidine in combination
with etoposide. The release test results exhibited that the cinchona
alkaloids release released faster than that of etoposide. Collectively,
cinchona alkaloids can be packaged along with etoposide in
nanomicelles for better cancer therapy.
Abstract: Bone remodeling occurs by the balanced action of
bone resorbing osteoclasts (OC) and bone-building osteoblasts.
Increased bone resorption by excessive OC activity contributes
to malignant and non-malignant diseases including osteoporosis.
To study OC differentiation and function, OC formed in
in vitro cultures are currently counted manually, a tedious
procedure which is prone to inter-observer differences. Aiming
for an automated OC-quantification system, classification of
OC and precursor cells was done on fluorescence microscope
images based on the distinct appearance of fluorescent nuclei.
Following ellipse fitting to nuclei, a combination of eight
features enabled clustering of OC and precursor cell nuclei.
After evaluating different machine-learning techniques, LOGREG
achieved 74% correctly classified OC and precursor cell
nuclei, outperforming human experts (best expert: 55%). In
combination with the automated detection of total cell areas,
this system allows to measure various cell parameters and most
importantly to quantify proteins involved in osteoclastogenesis.