Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: A new voltage-mode triple-input single-output multifunction filter using only two current conveyors is presented. The proposed filter which possesses three inputs and single-output can generate all biquadratic filtering functions at the output terminal by selecting different input signal combinations. The validity of the proposed filter is verified through PSPICE simulations.
Abstract: In the present work we investigate both the elastic and
electric properties of a chiral material. We consider a composite
structure made from a polymer matrix and anisotropic inclusions of
GaAs taking into account piezoelectric and dielectric properties of
the composite material. The principal task of the work is the
estimation of the functional properties of the composite material.
Abstract: Stair climbing is one of critical issues for field robots to
widen applicable areas. This paper presents optimal design on
kinematic parameters of a new robotic platform for stair climbing. The
robotic platform climbs various stairs by body flip locomotion with
caterpillar type main platform. Kinematic parameters such as platform
length, platform height, and caterpillar rotation speed are optimized to
maximize stair climbing stability. Three types of stairs are used to
simulate typical user conditions. The optimal design process is
conducted based on Taguchi methodology, and resulting parameters
with optimized objective function are presented. In near future, a
prototype is assembled for real environment testing.
Abstract: Structural redundancy is an interesting point in
seismic design of structures. Initially, the structural redundancy is
described as indeterminate degree of a system. Although many definitions are presented for redundancy in structures, recently the
definition of structural redundancy has been related to the configuration of structural system and the number of lateral load
transferring directions in the structure. The steel frames with infill walls are general systems in the constructing of usual residential buildings in some countries. It is
obviously declared that the performance of structures will be affected by adding masonry infill walls. In order to investigate the effect of
infill walls on the redundancy of the steel frame which constructed
with masonry walls, the components of redundancy including redundancy variation index, redundancy strength index and
redundancy response modification factor were extracted for the
frames with masonry infills. Several steel frames with typical storey number and various numbers of bays were designed and considered.
The redundancy of frames with and without infill walls was evaluated by proposed method. The results showed the presence of infill causes increase of redundancy.
Abstract: This article presents a resistorless current-mode firstorder allpass filter based on second generation current controlled current conveyors (CCCIIs). The features of the circuit are that: the pole frequency can be electronically controlled via the input bias current: the circuit description is very simple, consisting of 2 CCCIIs and single grounded capacitor, without any external resistors and component matching requirements. Consequently, the proposed circuit is very appropriate to further develop into an integrated circuit. Low input and high output impedances of the proposed configuration enable the circuit to be cascaded in current-mode without additional current buffers. The PSpice simulation results are depicted. The given results agree well with the theoretical anticipation. The application example as a current-mode quadrature oscillator is included.
Abstract: This paper reviews recent studies and particularly the
effects of Climate Change in the North Tropical Atlantic by studying
atmospheric conditions that prevailed in 2005 ; Coral Bleaching
HotSpot and Hurricane Katrina. In the aim to better understand and
estimate the impact of the physical phenomenon, i.e. Thermal
Oceanic HotSpot (TOHS), isotopic studies of δ18O and δ13C on
marine animals from Guadeloupe (French Caribbean Island) were
carried out. Recorded measures show Sea Surface Temperature (SST)
up to 35°C in August which is much higher than data recorded by
NOAA satellites 32°C. After having reviewed the process that led to
the creation of Hurricane Katrina which hit New Orleans in August
29, 2005, it will be shown that the climatic conditions in the
Caribbean from August to October 2005 have influenced Katrina
evolution. This TOHS is a combined effect of various phenomenon
which represent an additional factor to estimate future climate
changes.
Abstract: BioEnergy is an archetypal appropriate technology
and alternate source of energy in rural areas of China, and can meet
the basic need for cooking fuel in rural areas. The paper introduces
with an alternate mean of research that can accelerate the biogas
energy production. Tithonia diversifolia or the Tree marigold can be
hailed as mesophillic anaerobic digestion to increase the production
of more Bioenergy. Tithonia diversifolia is very native to Mexico and
Central America, which can be served as ornamental plants- green
manure and can prevent soil erosion. Tithonia diversifolia is widely
grown and known to Asia, Africa, America and Australia as well.
Nowadays, Considering China’s geographical condition it is found
that Tithonia diversifolia is widely growing plant in the many tropical
and subtropical regions of southern Yunnan- which can have great
usage in accelerating and increasing the Bioenergy production
technology. The paper discussed aiming at proving possibility that
Tithonia diversifolia can be applied in biogas fermentation and its
biogas production potential, the research carried experiment on
Tithonia diversifolia biogas fermentation under the mesophilic
condition (35 Celsius Degree). The result revealed that Tithonia
diversifolia can be used as biogas fermentative material, and 6%
concentration can get the best biogas production, with the TS biogas
production rate 656mL/g and VS biogas production rate 801mL/g. It
is well addressed that Tithonia diversifolia grows wildly in 53
Counties and 9 cities of Yunnan Province, which mainly grows in
form of the road side plants, the edge of the field, countryside, forest
edge, open space; of which demersum-natures can form dense
monospecific beds -causing serious harm to agricultural production
landforms threatening the ecological system as a potentially harmful
exotic plant. There are also found the three types of invasive daisy
alien plants -Eupatorium adenophorum, Eupatorium Odorata and
Tithonia diversifolia in Yunnan Province of China-among them the
Tithonia diversifolia is responsible for causing serious harm to
agricultural production. In this paper we have designed the
experimental explanation of Biogas energy production that requires
anaerobic environment and some microbes; Tithonia diversifolia
plant has been taken into consideration while carrying experiments
and with successful resulting of generating more BioEnergy
emphasizing on the practical applications of Tithonia diversifolia.
This paper aims at- to find a new mechanism to provide a more
scientific basis for the development of this plant herbicides in Biogas
energy and to improve the utilization throughout the world as well.
Abstract: The paper proposes a new concept in developing
collaborative design system. The concept framework involves
applying simulation of supply chain management to collaborative
design called – 'SCM–Based Design Tool'. The system is developed
particularly to support design activities and to integrate all facilities
together. The system is aimed to increase design productivity and
creativity. Therefore, designers and customers can collaborate by the
system since conceptual design. JAG: Jewelry Art Generator based
on artificial intelligence techniques is integrated into the system.
Moreover, the proposed system can support users as decision tool
and data propagation. The system covers since raw material supply
until product delivery. Data management and sharing information are
visually supported to designers and customers via user interface. The
system is developed on Web–assisted product development
environment. The prototype system is presented for Thai jewelry
industry as a system prototype demonstration, but applicable for
other industry.
Abstract: Does the spatial perspective provide a common thread for rural sociology? Have rural sociologists succeeded in bringing order to their data using spatial analysis models and techniques? A trial answer to such questions, as touchstones of theoretical and applied sociological studies in rural areas, is the point at issue in the present paper. Spatial analyses have changed the way rural sociologists approach scientific problems. Rural sociology is spatial by nature because much, if not most, of its research topics has a spatial “awareness." However, such spatial awareness is not quite the same as spatial analysis because it is not typically associated with underlying theories and hypotheses about spatial patterns that are designed to be tested for their specific spatial content. This paper presents pressing issues for future research to reintroduce mainstream rural sociology to the concept of space.
Abstract: In this article an isotropic linear elastic half-space with
a cylindrical cavity of finite length is considered to be under the
effect of a ring shape time-harmonic torsion force applied at an
arbitrary depth on the surface of the cavity. The equation of
equilibrium has been written in a cylindrical coordinate system. By
means of Fourier cosine integral transform, the non-zero
displacement component is obtained in the transformed domain. With
the aid of the inversion theorem of the Fourier cosine integral
transform, the displacement is obtained in the real domain. With the
aid of boundary conditions, the involved boundary value problem for
the fundamental solution is reduced to a generalized Cauchy singular
integral equation. Integral representation of the stress and
displacement are obtained, and it is shown that their degenerated
form to the static problem coincides with existing solutions in the
literature.
Abstract: Green buildings have been commonly cited to be more
expensive than conventional buildings. However, limited research
has been conducted to clearly identify elements that contribute to this
cost differential. The construction cost of buildings can be typically
divided into “hard" costs and “soft" cost elements. Using a review
analysis of existing literature, the study identified six main elements
in green buildings that contribute to the general cost elements that are
“soft" in nature. The six elements found are insurance, developer-s
experience, design cost, certification, commissioning and energy
modeling. Out of the six elements, most literatures have highlighted
the increase in design cost for green design as compared to
conventional design due to additional architectural and engineering
costs, eco-charettes, extra design time, and the further need for a
green consultant. The study concluded that these elements of soft cost
contribute to the green premium or cost differential of green
buildings.
Abstract: This paper proposes a vehicle-to-vehicle propagation
model implemented with SDL. To estimate the channel
characteristics for Inter-Vehicle communication, we first define a
predicted propagation pathloss between the moving vehicles under
three typical scenarios. A Ray-tracing method is used for the simple
gamma model performance.
Abstract: The Electronic Health Record (EHR) system is very
general and we should pay more attention to a patient-s privacy. The
patient-s consent is one of the elements when dealing with privacy
topics. This study focuses on the creating and managing of patient
consent. The integration of the HL7 standards and the IHE BPPC
profile provides a base for the creation of patient consent. Establishing
the platform offers the patients a way to create, revoke or update their
consents. Through this platform, they can manage their consents in an
easier manner.
Abstract: In this project, a tele-operated anthropomorphic
robotic arm and hand is designed and built as a versatile robotic arm
system. The robot has the ability to manipulate objects such as pick
and place operations. It is also able to function by itself, in
standalone mode.
Firstly, the robotic arm is built in order to interface with a personal
computer via a serial servo controller circuit board. The circuit board
enables user to completely control the robotic arm and moreover,
enables feedbacks from user. The control circuit board uses a
powerful integrated microcontroller, a PIC (Programmable Interface
Controller). The PIC is firstly programmed using BASIC (Beginner-s
All-purpose Symbolic Instruction Code) and it is used as the 'brain'
of the robot. In addition a user friendly Graphical User Interface
(GUI) is developed as the serial servo interface software using
Microsoft-s Visual Basic 6.
The second part of the project is to use speech recognition control
on the robotic arm. A speech recognition circuit board is constructed
with onboard components such as PIC and other integrated circuits. It
replaces the computers- Graphical User Interface. The robotic arm is
able to receive instructions as spoken commands through a
microphone and perform operations with respect to the commands
such as picking and placing operations.
Abstract: Voltage collapse is instability of heavily loaded electric
power systems that cause to declining voltages and blackout. Power
systems are predicated to become more heavily loaded in the future
decade as the demand for electric power rises while economic and
environmental concerns limit the construction of new transmission
and generation capacity. Heavily loaded power systems are closer to
their stability limits and voltage collapse blackouts will occur if
suitable monitoring and control measures are not taken. To control
transmission lines, it can be used from FACTS devices.
In this paper Harmony search algorithm (HSA) and Genetic
Algorithm (GA) have applied to determine optimal location of
FACTS devices in a power system to improve power system stability.
Three types of FACTS devices (TCPAT, UPFS, and SVC) have been
introduced. Bus under voltage has been solved by controlling reactive
power of shunt compensator. Also a combined series-shunt
compensators has been also used to control transmission power flow
and bus voltage simultaneously.
Different scenarios have been considered. First TCPAT, UPFS, and
SVC are placed solely in transmission lines and indices have been
calculated. Then two types of above controller try to improve
parameters randomly. The last scenario tries to make better voltage
stability index and losses by implementation of three types controller
simultaneously. These scenarios are executed on typical 34-bus test
system and yields efficiency in improvement of voltage profile and
reduction of power losses; it also may permit an increase in power
transfer capacity, maximum loading, and voltage stability margin.
Abstract: This paper proposes an Interactive Chinese Character
Learning System (ICCLS) based on pictorial evolution as an
edutainment concept in computer-based learning of language. The
advantage of the language origination itself is taken as a learning
platform due to the complexity in Chinese language as compared to
other types of languages. Users especially children enjoy more by
utilize this learning system because they are able to memories the
Chinese Character easily and understand more of the origin of the
Chinese character under pleasurable learning environment, compares
to traditional approach which children need to rote learning Chinese
Character under un-pleasurable environment. Skeletonization is used
as the representation of Chinese character and object with an animated
pictograph evolution to facilitate the learning of the language. Shortest
skeleton path matching technique is employed for fast and accurate
matching in our implementation. User is required to either write a
word or draw a simple 2D object in the input panel and the matched
word and object will be displayed as well as the pictograph evolution
to instill learning. The target of computer-based learning system is for
pre-school children between 4 to 6 years old to learn Chinese
characters in a flexible and entertaining manner besides utilizing
visual and mind mapping strategy as learning methodology.
Abstract: In this work we evaluate the possibility of predicting
the emotional state of a person based on the EEG. We investigate
the problem of classifying valence from EEG signals during
the presentation of affective pictures, utilizing the "frontal EEG
asymmetry" phenomenon. To distinguish positive and negative
emotions, we applied the Common Spatial Patterns algorithm.
In contrast to our expectations, the affective pictures did not
reliably elicit changes in frontal asymmetry. The classifying task
thereby becomes very hard as reflected by the poor classifier
performance. We suspect that the masking of the source of the
brain activity related to emotions, coming mostly from deeper
structures in the brain, and the insufficient emotional engagement
are among main reasons why it is difficult to predict the emotional
state of a person.
Abstract: Recently, genetic algorithms (GA) and particle swarm optimization (PSO) technique have attracted considerable attention among various modern heuristic optimization techniques. The GA has been popular in academia and the industry mainly because of its intuitiveness, ease of implementation, and the ability to effectively solve highly non-linear, mixed integer optimization problems that are typical of complex engineering systems. PSO technique is a relatively recent heuristic search method whose mechanics are inspired by the swarming or collaborative behavior of biological populations. In this paper both PSO and GA optimization are employed for finding stable reduced order models of single-input- single-output large-scale linear systems. Both the techniques guarantee stability of reduced order model if the original high order model is stable. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical example from literature and the results are compared with recently published conventional model reduction technique.
Abstract: Contamination of heavy metals in tin tailings has
caused an interest in the scientific approach of their remediation. One
of the approaches is through phytoremediation, which is using tree
species to extract the heavy metals from the contaminated soils. Tin
tailings comprise of slime and sand tailings. This paper reports only
on the finding of the four timber species namely Acacia mangium,
Hopea odorata, Intsia palembanica and Swietenia macrophylla on
the removal of cadmium (Cd) and lead (Pb) from the slime tailings.
The methods employed for sampling and soil analysis are established
methods. Six trees of each species were randomly selected from a
0.25 ha plot for extraction and determination of their heavy metals.
The soil samples were systematically collected according to 5 x 5 m
grid from each plot. Results showed that the concentration of heavy
metals in soils and trees varied according to species. Higher
concentration of heavy metals was found in the stem than the
primary roots of all the species. A. Mangium accumulated the highest
total amount of Pb per hectare basis.