Abstract: For fire safety purposes, the fire resistance and the
structural behavior of reinforced concrete members are assessed to
satisfy specific fire performance criteria. The available prescribed
provisions are based on standard fire load. Under various fire
scenarios, engineers are in need of both heat transfer analysis and
structural analysis. For heat transfer analysis, the study proposed a
modified finite difference method to evaluate the temperature profile
within a cross section. The research conducted is limited to concrete
sections exposed to a fire on their one side. The method is based on
the energy conservation principle and a pre-determined power
function of the temperature profile. The power value of 2.7 is found
to be a suitable value for concrete sections. The temperature profiles
of the proposed method are only slightly deviate from those of the
experiment, the FEM and the FDM for various fire loads such as
ASTM E 119, ASTM 1529, BS EN 1991-1-2 and 550 oC. The
proposed method is useful to avoid incontinence of the large matrix
system of the typical finite difference method to solve the
temperature profile. Furthermore, design engineers can simply apply
the proposed method in regular spreadsheet software.
Abstract: This paper investigated the organizational
innovativeness of public listed housing developers in Malaysia. We
conceptualized organizational innovativeness as a multi-dimensional
construct consisting of 5 dimensions: market innovativeness, product
innovativeness, process innovativeness, behavior innovativeness and
strategic innovativeness. We carried out questionnaire survey with all
accessible public listed developers in Malaysia and received a 56
percent response. We found that the innovativeness of public listed
housing developers is low. The study extends the knowledge on
innovativeness theory by using a multi-dimensional contructs to
conceptualize the innovativeness of public listed housing developers
in Malaysia where all this while most studies focused on single
dimensional construct of innovativeness. The paper ends by
providing some explanations for the results.
Abstract: This study is concerned with the investigation of the
suitability of several empirical and semi-empirical drying models
available in the literature to define drying behavior of viscose yarn
bobbins. For this purpose, firstly, experimental drying behaviour of
viscose bobbins was determined on an experimental dryer setup
which was designed and manufactured based on hot-air bobbin
dryers used in textile industry. Afterwards, drying models considered
were fitted to the experimentally obtained moisture ratios. Drying
parameters were drying temperature and bobbin diameter. The fit
was performed by selecting the values for constants in the models in
such a way that these values make the sum of the squared differences
between the experimental and the model results for moisture ratio
minimum. Suitability of fitting was specified as comparing the
correlation coefficient, standard error and mean square deviation.
The results show that the most appropriate model in describing the
drying curves of viscose bobbins is the Page model.
Abstract: The ability of the brain to organize information and generate the functional structures we use to act, think and communicate, is a common and easily observable natural phenomenon. In object-oriented analysis, these structures are represented by objects. Objects have been extensively studied and documented, but the process that creates them is not understood. In this work, a new class of discrete, deterministic, dissipative, host-guest dynamical systems is introduced. The new systems have extraordinary self-organizing properties. They can host information representing other physical systems and generate the same functional structures as the brain does. A simple mathematical model is proposed. The new systems are easy to simulate by computer, and measurements needed to confirm the assumptions are abundant and readily available. Experimental results presented here confirm the findings. Applications are many, but among the most immediate are object-oriented engineering, image and voice recognition, search engines, and Neuroscience.
Abstract: Five crystal modifications of water insoluble
artesunate were generated by recrystallizing it from various solvents
with improved physicochemical properties. These generated crystal
forms were characterized to select the most potent and soluble form.
SEM of all the forms showed changes in external shape leading them
to be different morphologically. DSC thermograms of Form III and
Form V showed broad endotherm peaks at 83.04oC and 76.96oC prior
to melting fusion of drug respectively. Calculated weight loss in TGA
revealed that Form III and Form V are methanol and acetone solvates
respectively. However, few additional peaks were appeared in XRPD
pattern in these two solvate forms. All forms exhibit exothermic
behavior in buffer and two solvates display maximum ease of
molecular release from the lattice. Methanol and acetone solvates
were found to be most soluble forms and exhibited higher
antimalarial efficacy showing higher survival rate (83.3%) after 30
days.
Abstract: This paper deals with stakeholders’ decisions within energy neutral urban redevelopment processes. The decisions of these stakeholders during the process will make or break energy neutral ambitions. An extensive form of game theory model gave insight in the behavioral differences of stakeholders regarding energy neutral ambitions and the effects of the changing legislation. The results show that new legislation regarding spatial planning slightly influences the behavior of stakeholders. An active behavior of the municipality will still result in the best outcome. Nevertheless, the municipality becomes more powerful when acting passively and can make the use of planning tools to provide governance towards energy neutral urban redevelopment. Moreover, organizational support, recognizing the necessity for energy neutrality, keeping focused and collaboration among stakeholders are crucial elements to achieve the objective of an energy neutral urban (re)development.
Abstract: Testing is an activity that is required both in the
development and maintenance of the software development life cycle
in which Integration Testing is an important activity. Integration
testing is based on the specification and functionality of the software
and thus could be called black-box testing technique. The purpose of
integration testing is testing integration between software
components. In function or system testing, the concern is with overall
behavior and whether the software meets its functional specifications
or performance characteristics or how well the software and
hardware work together. This explains the importance and necessity
of IT for which the emphasis is on interactions between modules and
their interfaces. Software errors should be discovered early during
IT to reduce the costs of correction. This paper introduces a new type
of integration error, presenting an overview of Integration Testing
techniques with comparison of each technique and also identifying
which technique detects what type of error.
Abstract: One of the long standing challenging aspect in mobile robotics is the ability to navigate autonomously, avoiding modeled and unmodeled obstacles especially in crowded and unpredictably changing environment. A successful way of structuring the navigation task in order to deal with the problem is within behavior based navigation approaches. In this study, Issues of individual behavior design and action coordination of the behaviors will be addressed using fuzzy logic. A layered approach is employed in this work in which a supervision layer based on the context makes a decision as to which behavior(s) to process (activate) rather than processing all behavior(s) and then blending the appropriate ones, as a result time and computational resources are saved.
Abstract: The UML modeling of complex distributed systems often is a great challenge due to the large amount of parallel real-time operating components. In this paper the problems of verification of such systems are discussed. ECPN, an Extended Colored Petri Net is defined to formally describe state transitions of components and interactions among components. The relationship between sequence diagrams and Free Choice Petri Nets is investigated. Free Choice Petri Net theory helps verifying the liveness of sequence diagrams. By converting sequence diagrams to ECPNs and then comparing behaviors of sequence diagram ECPNs and statecharts, the consistency among models is analyzed. Finally, a verification process for an example model is demonstrated.
Abstract: This study investigated a strategy of blending lead-laden sludge and Al-rich precursors to reduce the release of metals from the stabilized products. Using PbO as the simulated lead-laden sludge to sinter with γ-Al2O3 by Pb:Al molar ratios of 1:2 and 1:12, PbAl2O4 and PbAl12O19 were formed as final products during the sintering process, respectively. By firing the PbO + γ-Al2O3 mixtures with different Pb/Al molar ratios at 600 to 1000 °C, the lead transformation was determined through X-ray diffraction (XRD) data. In Pb/Al molar ratio of 1/2 system, the formation of PbAl2O4 is initiated at 700 °C, but an effective formation was observed above 750 °C. An intermediate phase, Pb9Al8O21, was detected in the temperature range of 800-900 °C. However, different incorporation behavior for sintering PbO with Al-rich precursors at a Pb/Al molar ratio of 1/12 was observed during the formation of PbAl12O19 in this system. In the sintering process, both temperature and time effect on the formation of PbAl2O4 and PbAl12O19 phases were estimated. Finally, a prolonged leaching test modified from the U.S. Environmental Protection Agency-s toxicity characteristic leaching procedure (TCLP) was used to evaluate the durability of PbO, Pb9Al8O21, PbAl2O4 and PbAl12O19 phases. Comparison for the leaching results of the four phases demonstrated the higher intrinsic resistance of PbAl12O19 against acid attack.
Abstract: The hot deformation behavior of high strength low
alloy (HSLA) steels with different chemical compositions under hot
working conditions in the temperature range of 900 to 1100℃ and
strain rate range from 0.1 to 10 s-1 has been studied by performing a
series of hot compression tests. The dynamic materials model has been
employed for developing the processing maps, which show variation
of the efficiency of power dissipation with temperature and strain rate.
Also the Kumar-s model has been used for developing the instability
map, which shows variation of the instability for plastic deformation
with temperature and strain rate. The efficiency of power dissipation
increased with decreasing strain rate and increasing temperature in the
steel with higher Cr and Ti content. High efficiency of power
dissipation over 20 % was obtained at a finite strain level of 0.1 under
the conditions of strain rate lower than 1 s-1 and temperature higher
than 1050 ℃ . Plastic instability was expected in the regime of
temperatures lower than 1000 ℃ and strain rate lower than 0.3 s-1. Steel
with lower Cr and Ti contents showed high efficiency of power
dissipation at higher strain rate and lower temperature conditions.
Abstract: Road signs are the elements of roads with a lot of
influence in driver-s behavior. So that signals can fulfill its function,
they must overcome visibility and durability requirements,
particularly needed at night, when the coefficient of retroreflection
becomes a decisive factor in ensuring road safety. Accepting that the
visibility of the signage has implications for people-s safety, we
understand the importance to fulfill its function: to foster the highest
standards of service and safety in drivers. The usual conditions of
perception of any sign are determined by: age of the driver, reflective
material, luminosity, vehicle speed and emplacement. In this way,
this paper evaluates the different signals to increase the safety road.
Abstract: This research is a collaborative narrative research, which is mixed with issues of selected papers and researcher's experience as an anonymous user on social networking sites. The objective of this research is to understand the reasons of the regular users who reject to contact with anonymous users, and to study the communication traditions used in the selected studies. Anonymous users are rejected by regular users, because of the fear of cyber bully, the fear of unpleasant behaviors, and unwillingness of changing communication norm. The suggestion for future research design is to use longitudinal design or quantitative design; and the theory in rhetorical tradition should be able to help develop a strong trust message.
Abstract: The modeling of inelastic behavior of plastic materials requires measurements providing information on material response to different multiaxial loading conditions. Different triaxiality conditions and values of Lode parameters have to be
covered for complex description of the material plastic behavior.
Samples geometries providing material plastic behavoiur over the range of interest are proposed with the use of FEM analysis. Round samples with 3 different notches and smooth surface are used
together with butterfly type of samples tested at angle ranging for 0 to
90°. Identification of ductile damage parameters is carried out on
the basis of obtained experimental data for austenitic stainless steel.
The obtained material plastic damage parameters are subsequently applied to FEM simulation of notched CT normally samples used for
fracture mechanics testing and results from the simulation are
compared with real tests.
Abstract: In order to alleviate the mental and physical problems
of persons with disabilities, animal-assisted therapy (AAT) is one of
the possible modalities that employs the merit of the human-animal
interaction. Nevertheless, to achieve the purpose of AAT for persons
with severe disabilities (e.g. spinal cord injury, stroke, and
amyotrophic lateral sclerosis), real-time animal language
interpretation is desirable. Since canine behaviors can be visually
notable from its tail, this paper proposes the automatic real-time
interpretation of canine tail language for human-canine interaction in
the case of persons with severe disabilities. Canine tail language is
captured via two 3-axis accelerometers. Directions and frequencies
are selected as our features of interests. The novel fuzzy rules based
on Gaussian-Trapezoidal model and center of gravity (COG)-based
defuzzification method are proposed in order to interpret the features
into four canine emotional behaviors, i.e., agitate, happy, scare and
neutral as well as its blended emotional behaviors. The emotional
behavior model is performed in the simulated dog and has also been
evaluated in the real dog with the perfect recognition rate.
Abstract: The flow field and the motion of the free surface in an
oscillating container are simulated numerically to assess the numerical
approach for studying two-phase flows under oscillating conditions.
Two numerical methods are compared: one is to model the oscillating
container directly using the moving grid of the ALE method, and the
other is to simulate the effect of container motion using the oscillating
body force acting on the fluid in the stationary container. The
two-phase flow field in the container is simulated using the level set
method in both cases. It is found that the calculated results by the body
force method coinsides with those by the moving grid method and the
sloshing behavior is predicted well by both the methods. Theoretical
back ground and limitation of the body force method are discussed,
and the effects of oscillation amplitude and frequency are shown.
Abstract: This paper presents a numerical analysis of the
performance of a three-bladed Darrieus vertical-axis wind turbine
based on the DU91-W2-250 airfoil. A complete campaign of 2-D
simulations, performed for several values of tip speed ratio and based
on RANS unsteady calculations, has been performed to obtain the
rotor torque and power curves. Rotor performances have been
compared with the results of a previous work based on the use of the
NACA 0021 airfoil. Both the power coefficient and the torque
coefficient have been determined as a function of the tip speed ratio.
The flow field around rotor blades has also been analyzed. As a final
result, the performance of the DU airfoil based rotor appears to be
lower than the one based on the NACA 0021 blade section. This
behavior could be due to the higher stall characteristics of the NACA
profile, being the separation zone at the trailing edge more extended
for the DU airfoil.
Abstract: This article is an extension and a practical application
approach of Wheeler-s NEBIC theory (Net Enabled Business
Innovation Cycle). NEBIC theory is a new approach in IS research
and can be used for dynamic environment related to new technology.
Firms can follow the market changes rapidly with support of the IT
resources. Flexible firms adapt their market strategies, and respond
more quickly to customers changing behaviors. When every leading
firm in an industry has access to the same IT resources, the way that
these IT resources are managed will determine the competitive
advantages or disadvantages of firm. From Dynamic Capabilities
Perspective and from newly introduced NEBIC theory by Wheeler,
we know that only IT resources cannot deliver customer value but
good configuration of those resources can guarantee customer value
by choosing the right emerging technology, grasping the right
economic opportunities through business innovation and growth. We
found evidences in literature that SOA (Service Oriented
Architecture) is a promising emerging technology which can deliver
the desired economic opportunity through modularity, flexibility and
loose-coupling. SOA can also help firms to connect in network which
can open a new window of opportunity to collaborate in innovation
and right kind of outsourcing. There are many articles and research
reports indicates that failure rate in outsourcing is very high but at the
same time research indicates that successful outsourcing projects
adds tangible and intangible benefits to the service consumer.
Business executives and policy makers in the west should not afraid
of outsourcing but they should choose the right strategy through the
use of emerging technology to significantly reduce the failure rate in
outsourcing.
Abstract: In a none-super-competitive environment the concepts
of closed system, management control remains to be the dominant
guiding concept to management. The merits of closed loop have been
the sources of most of the management literature and culture for
many decades. It is a useful exercise to investigate and poke into the
dynamics of the control loop phenomenon and draws some lessons to
use for refining the practice of management. This paper examines the
multitude of lessons abstracted from the behavior of the Input /output
/feedback control loop model, which is the core of control theory.
There are numerous lessons that can be learned from the insights this
model would provide and how it parallels the management dynamics
of the organization. It is assumed that an organization is basically a
living system that interacts with the internal and external variables. A
viable control loop is the one that reacts to the variation in the
environment and provide or exert a corrective action. In managing
organizations this is reflected in organizational structure and
management control practices. This paper will report findings that
were a result of examining several abstract scenarios that are
exhibited in the design, operation, and dynamics of the control loop
and how they are projected on the functioning of the organization.
Valuable lessons are drawn in trying to find parallels and new
paradigms, and how the control theory science is reflected in the
design of the organizational structure and management practices. The
paper is structured in a logical and perceptive format. Further
research is needed to extend these findings.
Abstract: By incorporating a prey refuge, this paper proposes new discrete Leslie–Gower predator–prey systems with and without Allee effect. The existence of fixed points are established and the stability of fixed points are discussed by analyzing the modulus of characteristic roots.