Abstract: Due to heightened concerns over environmental and economic issues the growing important of air pollution, and the importance of conserving fossil fuel resources in the world, the automotive industry is now forced to produce more fuel efficient, low emission vehicles and new drive system technologies. One of the most promising technologies to receive attention is the hybrid electric vehicle (HEV), which consists of two or more energy sources that supply energy to electric traction motors that in turn drive the wheels. This paper presents the various structures of HEV systems, the basic theoretical knowledge for describing their operation and the general behaviour of the HEV in acceleration, cruise and deceleration phases. The conventional design and sizing of a series HEV is studied. A conventional bus and its series configuration are defined and evaluated using the ADVISOR. In this section the simulation of a standard driving cycle and prediction of its fuel consumption and emissions of the HEV are discussed. Finally the bus performance is investigated to establish whether it can satisfy the performance, fuel consumption and emissions requested. The validity of the simulation has been established by the close conformity between the fuel consumption of the conventional bus reported by the manufacturer to what has achieved from the simulation.
Abstract: This paper presents and evaluates a new classification
method that aims to improve classifiers performances and speed up
their training process. The proposed approach, called labeled
classification, seeks to improve convergence of the BP (Back
propagation) algorithm through the addition of an extra feature
(labels) to all training examples. To classify every new example, tests
will be carried out each label. The simplicity of implementation is the
main advantage of this approach because no modifications are
required in the training algorithms. Therefore, it can be used with
others techniques of acceleration and stabilization. In this work, two
models of the labeled classification are proposed: the LMLP
(Labeled Multi Layered Perceptron) and the LNFC (Labeled Neuro
Fuzzy Classifier). These models are tested using Iris, wine, texture
and human thigh databases to evaluate their performances.
Abstract: Protective coatings that resist oxide scale growth and
decrease chromium evaporation are necessary to make stainless steel
interconnect materials for long-term durable operation of solid oxide
fuel cells (SOFCs). In this study a layer of cobalt was electroplated
on the surface of AISI 441 ferritic stainless steel which is used in
solid oxide fuel cells for interconnect applications. The oxidation
behavior of coated substrates was studied as a function of time at
operating conditions of SOFCs. Cyclic oxidation has been also tested
at 800ºC for 100 cycles. Cobalt coating during isothermal oxidation
caused to the oxide growth resistance by limiting the outward
diffusion of Cr cation and the inward diffusion of oxygen anion.
Results of cyclic oxidation exhibited that coated substrates
demonstrate an excellent resistance against the spallation and
cracking.
Abstract: The agriculture lignocellulosic by-products are receiving increased attention, namely in the search for filter materials that retain contaminants from water. These by-products, specifically almond and hazelnut shells are abundant in Portugal once almond and hazelnuts production is a local important activity. Hazelnut and almond shells have as main constituents lignin, cellulose and hemicelluloses, water soluble extractives and tannins. Along the adsorption of heavy metals from contaminated waters, water soluble compounds can leach from shells and have a negative impact in the environment. Usually, the chemical characterization of treated water by itself may not show environmental impact caused by the discharges when parameters obey to legal quality standards for water. Only biological systems can detect the toxic effects of the water constituents. Therefore, the evaluation of toxicity by biological tests is very important when deciding the suitability for safe water discharge or for irrigation applications.
The main purpose of the present work was to assess the potential impacts of waters after been treated for heavy metal removal by hazelnut and almond shells adsorption systems, with short term acute toxicity tests.
To conduct the study, water at pH 6 with 25 mg.L-1 of lead, was treated with 10 g of shell per litre of wastewater, for 24 hours. This procedure was followed for each bark. Afterwards the water was collected for toxicological assays; namely bacterial resistance, seed germination, Lemna minor L. test and plant grow. The effect in isolated bacteria strains was determined by disc diffusion method and the germination index of seed was evaluated using lettuce, with temperature and humidity germination control for 7 days. For aquatic higher organism, Lemnas were used with 4 days contact time with shell solutions, in controlled light and temperature. For terrestrial higher plants, biomass production was evaluated after 14 days of tomato germination had occurred in soil, with controlled humidity, light and temperature.
Toxicity tests of water treated with shells revealed in some extent effects in the tested organisms, with the test assays showing a close behaviour as the control, leading to the conclusion that its further utilization may not be considered to create a serious risk to the environment.
Abstract: Maximal Ratio Combining (MRC) is considered the most complex combining technique as it requires channel coefficients estimation. It results in the lowest bit error rate (BER) compared to all other combining techniques. However the BER starts to deteriorate as errors are introduced in the channel coefficients estimation. A novel combining technique, termed Generalized Maximal Ratio Combining (GMRC) with a polynomial kernel, yields an identical BER as MRC with perfect channel estimation and a lower BER in the presence of channel estimation errors. We show that GMRC outperforms the optimal MRC scheme in general and we hereinafter introduce it to the scientific community as a new “supraoptimal" algorithm. Since diversity combining is especially effective in small femto- and pico-cells, internet-associated wireless peripheral systems are to benefit most from GMRC. As a result, many spinoff applications can be made to IP-based 4th generation networks.
Abstract: This paper presents strategies for dynamically creating, managing and removing mesh cells during computations in the context of the Material Point Method (MPM). The dynamic meshing approach has been developed to help address problems involving motion of a finite size body in unbounded domains in which the extent of material travel and deformation is unknown a priori, such as in the case of landslides and debris flows. The key idea is to efficiently instantiate and search only cells that contain material points, thereby avoiding unneeded storage and computation. Mechanisms for doing this efficiently are presented, and example problems are used to demonstrate the effectiveness of dynamic mesh management relative to alternative approaches.
Abstract: Nowadays, without the awareness of consumer
behavior and correct understanding of it, it is not possible for organizations to take appropriate measures to meet the consumer
needs and demands. The aim of this paper is the identification and
prioritization of the factors affecting the consumer behavior based on
the product value. The population of the study includes all the
consumers of furniture producing firms in East Azarbaijan province,
Iran. The research sample includes 93 people selected by the sampling formula in unlimited population. The data collection
instrument was a questionnaire, the validity of which was confirmed
through face validity and the reliability of which was determined,
using Cronbach's alpha coefficient. The Kolmogorov-Smironov test
was used to test data normality, the t-test for identification of factors
affecting the product value, and Friedman test for prioritizing the
factors. The results show that quality, satisfaction, styling, price, finishing operation, performance, safety, worth, shape, use, and
excellence are placed from 1 to 11 priorities, respectively.
Abstract: Cashew nut shells were converted into activated carbon powders using KOH activation plus CO2 gasification at 1027 K. The increase both of impregnation ratio and activation time, there was swiftly the development of mesoporous structure with increasing of mesopore volume ratio from 20-28% and 27-45% for activated carbon with ratio of KOH per char equal to 1 and 4, respectively. Activated carbon derived from KOH/char ratio equal to 1 and CO2 gasification time from 20 to 150 minutes were exhibited the BET surface area increasing from 222 to 627 m2.g-1. And those were derived from KOH/char ratio of 4 with activation time from 20 to 150 minutes exhibited high BET surface area from 682 to 1026 m2.g-1. The adsorption of Lead(II) and Cadmium(II) ion was investigated. This adsorbent exhibited excellent adsorption for Lead(II) and Cadmium(II) ion. Maximum adsorption presented at 99.61% at pH 6.5 and 98.87% at optimum conditions. The experimental data was calculated from Freundlich isotherm and Langmuir isotherm model. The maximum capacity of Pb2+ and Cd2+ ions was found to be 28.90 m2.g-1 and 14.29 m2.g-1, respectively.
Abstract: Plants are rich sources of bioactive compounds. In this study the photochemical screening of hexane, ethanolic and aqueous extracts of roots and latex of jojoba (Simmondsia chinensis) plant revealed the presence of saponins, tannins, alkaloids, steroids and glycosides. Ethanolic extract was found to be richer in these metabolites than hexane, aqueous extracts and latex. The extracts and latex displayed effective antimicrobial activity against Salmonella typhimurium, Bacillus cereus, Clostridium perfringens, Staphylococcus aureus, Escherichia coli, Candida albicans and Aspergillus flavus. The increase in volume of the extracts and latex caused more activity, as shown by zones of inhibition. Candida albicans growth was inhibited only by hexane extract. Jojoba latex was not effective against Candida albicans at 0.1 and 0.5 ml extracts concentration but showed 5mm zone of inhibition at (1.0 ml). Lower volume (0.1ml) of latex encouraged Aspergillus flavus growth, while at (1.00 ml) reduced its mycelial growth. Thus, jojoba root extracts and latex can be of potential natural antimicrobial agents.
Abstract: The goal of Gene Expression Analysis is to understand the processes that underlie the regulatory networks and pathways controlling inter-cellular and intra-cellular activities. In recent times microarray datasets are extensively used for this purpose. The scope of such analysis has broadened in recent times towards reconstruction of gene networks and other holistic approaches of Systems Biology. Evolutionary methods are proving to be successful in such problems and a number of such methods have been proposed. However all these methods are based on processing of genotypic information. Towards this end, there is a need to develop evolutionary methods that address phenotypic interactions together with genotypic interactions. We present a novel evolutionary approach, called Phenomic algorithm, wherein the focus is on phenotypic interaction. We use the expression profiles of genes to model the interactions between them at the phenotypic level. We apply this algorithm to the yeast sporulation dataset and show that the algorithm can identify gene networks with relative ease.
Abstract: In this paper we are interested in Moufang-Klingenberg
planesM(A) defined over a local alternative ring A of dual numbers.
We introduce two new collineations of M(A).
Abstract: Chitosan is an attractive polysaccharide obtained by
deacetylation of an abundant natural biopolymer called chitin. Chitin
and chitosan are excellent materials. To improve the potential of
chitin and chitosan modification is needed. In the present study,
grafting of maleic acid on to chitosan by cerium ammonium nitrate in
acetic acid solution was investigated with use of a microwave and
reflux system. The grafted chitosan was characterized by using a
Fourier-transform infrared spectrometry. The solubility and swelling
behavior of grafted chitosans were determined in acetate buffer (pH
3.6), citrophosphate buffer (pH 5.6 and pH 7.0), and boric buffer (pH
9.2) solutions. The sample obtained by microwave system with use of
a chitosan/maleic anhydride/ceric ammonium nitrate 0.2/3.922/0.99
gram of raw material within 30 minute showed the maximum
swelling ratio (13.6) in boric buffer solution.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: Measurement of the quality of image compression is important for image processing application. In this paper, we propose an objective image quality assessment to measure the quality of gray scale compressed image, which is correlation well with subjective quality measurement (MOS) and least time taken. The new objective image quality measurement is developed from a few fundamental of objective measurements to evaluate the compressed image quality based on JPEG and JPEG2000. The reliability between each fundamental objective measurement and subjective measurement (MOS) is found. From the experimental results, we found that the Maximum Difference measurement (MD) and a new proposed measurement, Structural Content Laplacian Mean Square Error (SCLMSE), are the suitable measurements that can be used to evaluate the quality of JPEG200 and JPEG compressed image, respectively. In addition, MD and SCLMSE measurements are scaled to make them equivalent to MOS, given the rate of compressed image quality from 1 to 5 (unacceptable to excellent quality).
Abstract: During recent years, the traditional learning
approaches have undergone fundamental changes due to the
emergence of new technologies such as multimedia, hypermedia and
telecommunication. E-learning is a modern world phenomenon that
has come into existence in the information age and in a knowledgebased
society. E-learning has developed significantly within a short
period of time. Thus it is of a great significant to secure information,
allow a confident access and prevent unauthorized accesses. Making
use of individuals- physiologic or behavioral (biometric) properties is
a confident method to make the information secure. Among the
biometrics, fingerprint is more acceptable and most countries use it as
an efficient methods of identification. This article provides a new
method to compare the fingerprint comparison by pattern recognition
and image processing techniques. To verify fingerprint, the shortest
distance method is used together with perceptronic multilayer neural
network functioning based on minutiae. This method is highly
accurate in the extraction of minutiae and it accelerates comparisons
due to elimination of false minutiae and is more reliable compared
with methods that merely use directional images.
Abstract: The substrate heater designed for this investigation is a front side substrate heating system. It consists of 10 conventional tungsten halogen lamps and an aluminum reflector, total input electrical power of 5 kW. The substrate is heated by means of a radiation from conventional tungsten halogen lamps directed to the substrate through a glass window. This design allows easy replacement of the lamps and maintenance of the system. Within 2 to 6 minutes the substrate temperature reaches 500 to 830 C by varying the vertical distance between the glass window and the substrate holder. Moreover, the substrate temperature can be easily controlled by controlling the input power to the system. This design gives excellent opportunity to deposit many deferent films at deferent temperatures in the same deposition time. This substrate heater was successfully used for Chemical Vapor Deposition (CVD) of many thin films, such as Silicon, iron, etc.
Abstract: In the paper the results of calculations of the dynamic
response of a multi-storey reinforced concrete building to a strong
mining shock originated from the main region of mining activity in
Poland (i.e. the Legnica-Glogow Copper District) are presented. The
representative time histories of accelerations registered in three
directions were used as ground motion data in calculations of the
dynamic response of the structure. Two variants of a numerical model
were applied: the model including only structural elements of the
building and the model including both structural and non-structural
elements (i.e. partition walls and ventilation ducts made of brick). It
turned out that non-structural elements of multi-storey RC buildings
have a small impact of about 10 % on natural frequencies of these
structures. It was also proved that the dynamic response of building
to mining shock obtained in case of inclusion of all non-structural
elements in the numerical model is about 20 % smaller than in case
of consideration of structural elements only. The principal stresses
obtained in calculations of dynamic response of multi-storey building
to strong mining shock are situated on the level of about 30% of
values obtained from static analysis (dead load).
Abstract: Oxidative stress is considered to be the cause for onset
and the progression of type 2 diabetes mellitus (T2DM) and
complications including neuropathy. It is a deleterious process that
can be an important mediator of damage to cell structures: protein,
lipids and DNA. Data suggest that in patients with diabetes and
diabetic neuropathy DNA repair is impaired, which prevents effective
removal of lesions. Objective: The aim of our study was to evaluate
the association of the hOGG1 (326 Ser/Cys) and XRCC1 (194
Arg/Trp, 399 Arg/Gln) gene polymorphisms whose protein is
involved in the BER pathway with DNA repair efficiency in patients
with diabetes type 2 and diabetic neuropathy compared to the healthy
subjects. Genotypes were determined by PCR-RFLP analysis in 385
subjects, including 117 with type 2 diabetes, 56 with diabetic
neuropathy and 212 with normal glucose metabolism. The
polymorphisms studied include codon 326 of hOGG1 and 194, 399
of XRCC1 in the base excision repair (BER) genes. Comet assay was
carried out using peripheral blood lymphocytes from the patients and
controls. This test enabled the evaluation of DNA damage in cells
exposed to hydrogen peroxide alone and in the combination with the
endonuclease III (Nth). The results of the analysis of polymorphism
were statistically examination by calculating the odds ratio (OR) and
their 95% confidence intervals (95% CI) using the ¤ç2-tests. Our data
indicate that patients with diabetes mellitus type 2 (including those
with neuropathy) had higher frequencies of the XRCC1 399Arg/Gln
polymorphism in homozygote (GG) (OR: 1.85 [95% CI: 1.07-3.22],
P=0.3) and also increased frequency of 399Gln (G) allele (OR: 1.38
[95% CI: 1.03-1.83], P=0.3). No relation to other polymorphisms
with increased risk of diabetes or diabetic neuropathy. In T2DM
patients complicated by neuropathy, there was less efficient repair of
oxidative DNA damage induced by hydrogen peroxide in both the
presence and absence of the Nth enzyme. The results of our study
suggest that the XRCC1 399 Arg/Gln polymorphism is a significant
risk factor of T2DM in Polish population. Obtained data suggest a
decreased efficiency of DNA repair in cells from patients with
diabetes and neuropathy may be associated with oxidative stress.
Additionally, patients with neuropathy are characterized by even
greater sensitivity to oxidative damage than patients with diabetes,
which suggests participation of free radicals in the pathogenesis of
neuropathy.
Abstract: The use of new technologies such internet (e-mail, chat
rooms) and cell phones has steeply increased in recent years.
Especially among children and young people, use of technological
tools and equipments is widespread. Although many teachers and
administrators now recognize the problem of school bullying, few are
aware that students are being harassed through electronic
communication. Referred to as electronic bullying, cyber bullying, or
online social cruelty, this phenomenon includes bullying through email,
instant messaging, in a chat room, on a website, or through
digital messages or images sent to a cell phone. Cyber bullying is
defined as causing deliberate/intentional harm to others using internet
or other digital technologies. It has a quantitative research design nd
uses relational survey as its method. The participants consisted of
300 secondary school students in the city of Konya, Turkey. 195
(64.8%) participants were female and 105 (35.2%) were male. 39
(13%) students were at grade 1, 187 (62.1%) were at grade 2 and 74
(24.6%) were at grade 3. The “Cyber Bullying Question List"
developed by Ar─▒cak (2009) was given to students. Following
questions about demographics, a functional definition of cyber
bullying was provided. In order to specify students- human values,
“Human Values Scale (HVS)" developed by Dilmaç (2007) for
secondary school students was administered. The scale consists of 42
items in six dimensions. Data analysis was conducted by the primary
investigator of the study using SPSS 14.00 statistical analysis
software. Descriptive statistics were calculated for the analysis of
students- cyber bullying behaviour and simple regression analysis was
conducted in order to test whether each value in the scale could
explain cyber bullying behaviour.
Abstract: Yeast cells live in a constantly changing environment that requires the continuous adaptation of their genomic program in order to sustain their homeostasis, survive and proliferate. Due to the advancement of high throughput technologies, there is currently a large amount of data such as gene expression, gene deletion and protein-protein interactions for S. Cerevisiae under various environmental conditions. Mining these datasets requires efficient computational methods capable of integrating different types of data, identifying inter-relations between different components and inferring functional groups or 'modules' that shape intracellular processes. This study uses computational methods to delineate some of the mechanisms used by yeast cells to respond to environmental changes. The GRAM algorithm is first used to integrate gene expression data and ChIP-chip data in order to find modules of coexpressed and co-regulated genes as well as the transcription factors (TFs) that regulate these modules. Since transcription factors are themselves transcriptionally regulated, a three-layer regulatory cascade consisting of the TF-regulators, the TFs and the regulated modules is subsequently considered. This three-layer cascade is then modeled quantitatively using artificial neural networks (ANNs) where the input layer corresponds to the expression of the up-stream transcription factors (TF-regulators) and the output layer corresponds to the expression of genes within each module. This work shows that (a) the expression of at least 33 genes over time and for different stress conditions is well predicted by the expression of the top layer transcription factors, including cases in which the effect of up-stream regulators is shifted in time and (b) identifies at least 6 novel regulatory interactions that were not previously associated with stress-induced changes in gene expression. These findings suggest that the combination of gene expression and protein-DNA interaction data with artificial neural networks can successfully model biological pathways and capture quantitative dependencies between distant regulators and downstream genes.