Abstract: The spores of entomopathogenic fungi, Beauveria bassiana was evaluated for their compatibility with four surfactants; SDS (sodium dodyl sulphate) and CABS-65 (calcium alkyl benzene sulphonate), Tween 20 (polyethylene sorbitan monolaureate) and Tween 80 (polyoxyethylene sorbitan monoleate) at six different concentrations (0.1%, 0.5%, 1%, 2.5%, 5% and 10%). Incubated spores showed decrease in concentrations due to conversion of spores to hyphae. The maximum germination recorded in 72 h incubated spores varied with surfactant concentration at 49-68% (SDS), 39- 53% (CABS), 78-92% (Tween 80) and 80-92% (Tween 20), while the optimal surfactant concentration for spore germination was found to be 2.5-5%. The surfactant effect on spores was more pronounced with SDS and CABS-65, where significant deterioration and loss in viability of the incubated spores was observed. The effect of Tween 20 and Tween 80 were comparatively less inhibiting. The results of the study would help in surfactant selection for B. bassiana emulsion preparation.
Abstract: Data stream analysis is the process of computing
various summaries and derived values from large amounts of data
which are continuously generated at a rapid rate. The nature of a
stream does not allow a revisit on each data element. Furthermore,
data processing must be fast to produce timely analysis results. These
requirements impose constraints on the design of the algorithms to
balance correctness against timely responses. Several techniques
have been proposed over the past few years to address these
challenges. These techniques can be categorized as either dataoriented
or task-oriented. The data-oriented approach analyzes a
subset of data or a smaller transformed representation, whereas taskoriented
scheme solves the problem directly via approximation
techniques. We propose a hybrid approach to tackle the data stream
analysis problem. The data stream has been both statistically
transformed to a smaller size and computationally approximated its
characteristics. We adopt a Monte Carlo method in the approximation
step. The data reduction has been performed horizontally and
vertically through our EMR sampling method. The proposed method
is analyzed by a series of experiments. We apply our algorithm on
clustering and classification tasks to evaluate the utility of our
approach.
Abstract: In this paper, based on the coupled-mode and carrier rate equations, derivation of a dynamic model and numerically analysis of a MQW chirped DFB-SOA all-optical flip-flop is done precisely. We have analyzed the effects of strains of QW and MQW and cross phase modulation (XPM) on the dynamic response, and rise and fall times of the DFB-SOA all optical flip flop. We have shown that strained MQW active region in under an optimized condition into a DFB-SOA with chirped grating can improve the switching ON speed limitation in such a of the device, significantly while the fall time is increased. The values of the rise times for such an all optical flip-flop, are obtained in an optimized condition, areas tr=255ps.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: Over the past years, the EMCCD has had a profound
influence on photon starved imaging applications relying on its unique
multiplication register based on the impact ionization effect in the
silicon. High signal-to-noise ratio (SNR) means high image quality.
Thus, SNR improvement is important for the EMCCD. This work
analyzes the SNR performance of an EMCCD with gain off and on. In
each mode, simplified SNR models are established for different
integration times. The SNR curves are divided into readout noise (or
CIC) region and shot noise region by integration time. Theoretical
SNR values comparing long frame integration and frame adding in
each region are presented and discussed to figure out which method is
more effective. In order to further improve the SNR performance,
pixel binning is introduced into the EMCCD. The results show that
pixel binning does obviously improve the SNR performance, but at the
expensive of the spatial resolution.
Abstract: Random Oracle Model (ROM) is an effective method
for measuring the practical security of cryptograph. In this paper, we
try to use it into information hiding system (IHS). Because IHS has its
own properties, the ROM must be modified if it is used into IHS.
Firstly, we fully discuss why and how to modify each part of ROM
respectively. The main changes include: 1) Divide the attacks that IHS
may be suffered into two phases and divide the attacks of each phase
into several kinds. 2) Distinguish Oracles and Black-boxes clearly. 3)
Define Oracle and four Black-boxes that IHS used. 4) Propose the
formalized adversary model. And 5) Give the definition of judge.
Secondly, based on ROM of IHS, the security against known original
cover attack (KOCA-KOCA-security) is defined. Then, we give an
actual information hiding scheme and prove that it is
KOCA-KOCA-secure. Finally, we conclude the paper and propose the
open problems of further research.
Abstract: This paper presents Faults Forecasting System (FFS)
that utilizes statistical forecasting techniques in analyzing process
variables data in order to forecast faults occurrences. FFS is
proposing new idea in detecting faults. Current techniques used in
faults detection are based on analyzing the current status of the
system variables in order to check if the current status is fault or not.
FFS is using forecasting techniques to predict future timing for faults
before it happens. Proposed model is applying subset modeling
strategy and Bayesian approach in order to decrease dimensionality
of the process variables and improve faults forecasting accuracy. A
practical experiment, designed and implemented in Okayama
University, Japan, is implemented, and the comparison shows that
our proposed model is showing high forecasting accuracy and
BEFORE-TIME.
Abstract: The paper presents a part of the results obtained in a
complex research project on Romanian Grey Steppe breed, owner of
some remarkable qualities such as hardiness, longevity, adaptability,
special resistance to ban weather and diseases and included in the
genetic fund (G.D. no. 822/2008.) from Romania.
Following the researches effectuated, we identified alleles of six
loci, codifying the six types of major milk proteins: alpha-casein S1
(α S1-cz); beta-casein (β-cz); kappa-casein (K-cz); beta-lactoglobulin
(β-lg); alpha-lactalbumin (α-la) and alpha-casein S2 (α S2-cz). In
system αS1-cz allele αs1-Cn B has the highest frequency (0.700), in
system β-cz allele β-Cn A2 ( 0.550 ), in system K-cz allele k-CnA2 (
0.583 ) and heterozygote genotype AB ( 0.416 ) and BB (0.375), in
system β-lg allele β-lgA1 has the highest frequency (0.542 ) and
heterozygote genotype AB ( 0.500 ), in system α-la there is
monomorphism for allele α-la B and similarly in system αS2-cz for
allele αs2-Cn A.
The milk analysis by the isoelectric focalization technique (I.E.F.)
allowed the identification of a new allele for locus αS1-casein, for two
of the individuals under analysis, namely allele called αS1-casein
IRV. When experiments were repeated, we noticed that this is not a
proteolysis band and it really was a new allele that has not been
registered in the specialized literature so far. We identified two
heterozygote individuals, carriers of this allele, namely: BIRV and
CIRV. This discovery is extremely important if focus is laid on the
national genetic patrimony.
Abstract: The draw solute separation process in Forward
Osmosis desalination was simulated in Aspen Plus chemical process
modeling software, to estimate the energy consumption and compare
it with other desalination processes, mainly the Reverse Osmosis
process which is currently most prevalent. The electrolytic chemistry
for the system was retrieved using the Elec – NRTL property method
in the Aspen Plus database. Electrical equivalent of energy required
in the Forward Osmosis desalination technique was estimated and
compared with the prevalent desalination techniques.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: In this paper, we present a vertical nanowire thin film transistor with gate-all-around architecture, fabricated using CMOS compatible processes. A novel method of fabricating polysilicon vertical nanowires of diameter as small as 30 nm using wet-etch is presented. Both n-type and p-type vertical poly-silicon nanowire transistors exhibit superior electrical characteristics as compared to planar devices. On a poly-crystalline nanowire of 30 nm diameter, high Ion/Ioff ratio of 106, low drain-induced barrier lowering (DIBL) of 50 mV/V, and low sub-threshold slope SS~100mV/dec are demonstrated for a device with channel length of 100 nm.
Abstract: This paper deals with the design, development & implementation of a temperature sensor using zigbee. The main aim of the work undertaken in this paper is to sense the temperature and to display the result on the LCD using the zigbee technology. ZigBee operates in the industrial, scientific and medical (ISM) radio bands; 868 MHz in Europe, 915 MHz in the USA and 2.4 GHz in most jurisdictions worldwide. The technology is intended to be simpler and cheaper than other WPANs such as Bluetooth. The most capable ZigBee node type is said to require only about 10 % of the software of a typical Bluetooth or Wireless Internet node, while the simplest nodes are about 2 %. However, actual code sizes are much higher, more like 50 % of the Bluetooth code size. ZigBee chip vendors have announced 128-kilobyte devices. In this work undertaken in the design & development of the temperature sensor, it senses the temperature and after amplification is then fed to the micro controller, this is then connected to the zigbee module, which transmits the data and at the other end the zigbee reads the data and displays on to the LCD. The software developed is highly accurate and works at a very high speed. The method developed shows the effectiveness of the scheme employed.
Abstract: In wireless sensor network (WSN) the use of mobile
sink has been attracting more attention in recent times. Mobile sinks
are more effective means of balancing load, reducing hotspot
problem and elongating network lifetime. The sensor nodes in WSN
have limited power supply, computational capability and storage and
therefore for continuous data delivery reliability becomes high
priority in these networks. In this paper, we propose a Reliable
Energy-efficient Data Dissemination (REDD) scheme for WSNs with
multiple mobile sinks. In this strategy, sink first determines the
location of source and then directly communicates with the source
using geographical forwarding. Every forwarding node (FN) creates a
local zone comprising some sensor nodes that can act as
representative of FN when it fails. Analytical and simulation study
reveals significant improvement in energy conservation and reliable
data delivery in comparison to existing schemes.
Abstract: This paper proposes new algorithms for the computeraided
design and manufacture (CAD/CAM) of 3D woven multi-layer
textile structures. Existing commercial CAD/CAM systems are often
restricted to the design and manufacture of 2D weaves. Those
CAD/CAM systems that do support the design and manufacture of
3D multi-layer weaves are often limited to manual editing of design
paper grids on the computer display and weave retrieval from stored
archives. This complex design activity is time-consuming, tedious
and error-prone and requires considerable experience and skill of a
technical weaver. Recent research reported in the literature has
addressed some of the shortcomings of commercial 3D multi-layer
weave CAD/CAM systems. However, earlier research results have
shown the need for further work on weave specification, weave
generation, yarn path editing and layer binding. Analysis of 3D
multi-layer weaves in this research has led to the design and
development of efficient and robust algorithms for the CAD/CAM of
3D woven multi-layer textile structures. The resulting algorithmically
generated weave designs can be used as a basis for lifting plans that
can be loaded onto looms equipped with electronic shedding
mechanisms for the CAM of 3D woven multi-layer textile structures.
Abstract: This paper presents a new spread-spectrum
watermarking algorithm for digital images in discrete wavelet
transform (DWT) domain. The algorithm is applied for embedding
watermarks like patient identification /source identification or
doctors signature in binary image format into host digital
radiological image for potential telemedicine applications.
Performance of the algorithm is analysed by varying the gain factor,
subband decomposition levels, and size of watermark. Simulation
results show that the proposed method achieves higher watermarking
capacity.
Abstract: Real-time 3D applications have to guarantee
interactive rendering speed. There is a restriction for the number of
polygons which is rendered due to performance of a graphics hardware
or graphics algorithms. Generally, the rendering performance will be
drastically increased when handling only the dynamic 3d models,
which is much fewer than the static ones. Since shapes and colors of
the static objects don-t change when the viewing direction is fixed, the
information can be reused. We render huge amounts of polygon those
cannot handled by conventional rendering techniques in real-time by
using a static object image and merging it with rendering result of the
dynamic objects. The performance must be decreased as a
consequence of updating the static object image including removing
an static object that starts to move, re-rending the other static objects
being overlapped by the moving ones. Based on visibility of the object
beginning to move, we can skip the updating process. As a result, we
enhance rendering performance and reduce differences of rendering
speed between each frame. Proposed method renders total
200,000,000 polygons that consist of 500,000 dynamic polygons and
the rest are static polygons in about 100 frames per second.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.
Abstract: Global Solar Radiation (H) for Dubai and Sharjah,
Latitude 25.25oN, Longitude 55oE and 25.29oN, Longitude 55oE
respectively have been studied using sunshine hour data (n) of the
areas using various methods. These calculated global solar radiation
values are then compared to the measured values presented by
NASA. Furthermore, the extraterrestrial (H0), diffuse (Hd) and beam
radiation (Hb) are also calculated. The diffuse radiation is calculated
using methods proposed by Page and Liu and Jordan (L-J). Diffuse
Radiation from the Page method is higher than the L-J method.
Moreover, the clearness index (KT) signifies a clear sky almost all
year round. Rainy days are hardly a few in a year and limited in the
months December to March. The temperature remains between 25oC
in winter to 44oC in summer and is desirable for thermal applications
of solar energy. From the estimated results, it appears that solar
radiation can be utilized very efficiently throughout the year for
photovoltaic and thermal applications.
Abstract: The authors present a mixed method for reducing the order of the large-scale dynamic systems. In this method, the denominator polynomial of the reduced order model is obtained by using the modified pole clustering technique while the coefficients of the numerator are obtained by Pade approximations. This method is conceptually simple and always generates stable reduced models if the original high-order system is stable. The proposed method is illustrated with the help of the numerical examples taken from the literature.
Abstract: After allowing direct flights from Mainland China to
Taiwan, Chinese tourists increased according to Tourism
Bureaustatistics. There are from 0.19 to 2 million tourists from 2008 to
2011. Mainland China has become the main source of Taiwan
developing tourism industry. Taiwanese government should know
more about comments from Chinese tourists to Taiwan in order
toproperly market Taiwan tourism and enhance the overall quality of
tourism. In order to understand Chinese visitors’ comments, this study
adopts content analysis to analyze electronic word-of-mouth on Web.
This study collects 375 blog articles of Chinese tourists from
Ctrip.com as a database during 2009 to 2011. Through the qualitative
data analysis the traveling destination imagesis divided into seven
dimensions, such as senic spots, shopping, food and beverages,
accommodations, transportation, festivals and recreation activities.
Finally, this study proposes some practical managerial implication to
know both positive and negative images of the seven dimensions from
Chinese tourists, providing marketing strategies and suggestions to
traveling agency industry.