Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: Member States shall establish zones and
agglomerations throughout their territory to assess and manage air
quality in order to comply with European directives.
In Italy decree 155/2010, transposing Directive 2008/50/EC on
ambient air quality and cleaner air for Europe, merged into a single
act the previous provisions on ambient air quality assessment and
management, including those resulting from the implementation of
Directive 2004/107/EC relating to arsenic, cadmium, nickel, mercury
and polycyclic aromatic hydrocarbons in ambient air.
Decree 155/2010 introduced stricter rules for identifying zones on
the basis of the characteristics of the territory in spite of considering
pollution levels, as it was in the past. The implementation of such
new criteria has reduced the great variability of the previous zoning,
leading to a significant reduction of the total number of zones and to
a complete and uniform ambient air quality assessment and
management throughout the Country.
The present document is related to the new zones definition in
Italy according to Decree 155/2010. In particular the paper contains
the description and the analysis of the outcome of zoning and
classification.
Abstract: Bacterial strains capable of degradation of malathion
from the domestic sewage were isolated by an enrichment culture
technique. Three bacterial strains were screened and identified as
Acinetobacter baumannii (AFA), Pseudomonas aeruginosa (PS1),
and Pseudomonas mendocina (PS2) based on morphological,
biochemical identification and 16S rRNA sequence analysis.
Acinetobacter baumannii AFA was the most efficient malathion
degrading bacterium, so used for further biodegradation study. AFA
was able to grow in mineral salt medium (MSM) supplemented with
malathion (100 mg/l) as a sole carbon source, and within 14 days,
84% of the initial dose was degraded by the isolate measured by high
performance liquid chromatography. Strain AFA could also degrade
other organophosphorus compounds including diazinon, chlorpyrifos
and fenitrothion. The effect of different culture conditions on the
degradation of malathion like inoculum density, other carbon or
nitrogen sources, temperature and shaking were examined.
Degradation of malathion and bacterial cell growth were accelerated
when culture media were supplemented with yeast extract, glucose
and citrate. The optimum conditions for malathion degradation by
strain AFA were; an inoculum density of 1.5x 10^12CFU/ml at 30°C
with shaking. A specific polymerase chain reaction primers were
designed manually using multiple sequence alignment of the
corresponding carboxylesterase enzymes of Acinetobacter species.
Sequencing result of amplified PCR product and phylogenetic
analysis showed low degree of homology with the other
carboxylesterase enzymes of Acinetobacter strains, so we suggested
that this enzyme is a novel esterase enzyme. Isolated bacterial strains
may have potential role for use in bioremediation of malathion
contaminated.
Abstract: Fracture in hot precision forging of engine valves was
investigated in this paper. The entire valve forging procedure was
described and the possible cause of the fracture was proposed. Finite
Element simulation was conducted for the forging process, with
commercial Finite Element code DEFORMTM. The effects of
material properties, the effect of strain rate and temperature were
considered in the FE simulation. Two fracture criteria were discussed
and compared, based on the accuracy and reliability of the FE
simulation results. The selected criterion predicted the fracture
location and shows the trend of damage increasing with good
accuracy, which matches the experimental observation. Additional
modification of the punch shapes was proposed to further reduce the
tendency of fracture in forging. Finite Element comparison shows a
great potential of such application in the mass production.
Abstract: In this paper a real-time obstacle avoidance approach
for both autonomous and non-autonomous dynamical systems (DS) is
presented. In this approach the original dynamics of the controller
which allow us to determine safety margin can be modulated.
Different common types of DS increase the robot’s reactiveness in
the face of uncertainty in the localization of the obstacle especially
when robot moves very fast in changeable complex environments.
The method is validated by simulation and influence of different
autonomous and non-autonomous DS such as important
characteristics of limit cycles and unstable DS. Furthermore, the
position of different obstacles in complex environment is explained.
Finally, the verification of avoidance trajectories is described through
different parameters such as safety factor.
Abstract: Performance of different filtering approaches depends
on modeling of dynamical system and algorithm structure. For
modeling and smoothing the data the evaluation of posterior
distribution in different filtering approach should be chosen carefully.
In this paper different filtering approaches like filter KALMAN,
EKF, UKF, EKS and smoother RTS is simulated in some trajectory
tracking of path and accuracy and limitation of these approaches are
explained. Then probability of model with different filters is
compered and finally the effect of the noise variance to estimation is
described with simulations results.
Abstract: This paper presents a novel statistical description of
the counterpoise effective length due to lightning surges, where the
(impulse) effective length had been obtained by means of regressive
formulas applied to the transient simulation results. The effective
length is described in terms of a statistical distribution function, from
which median, mean, variance, and other parameters of interest could
be readily obtained. The influence of lightning current amplitude,
lightning front duration, and soil resistivity on the effective length has
been accounted for, assuming statistical nature of these parameters. A
method for determining the optimal counterpoise length, in terms of
the statistical impulse effective length, is also presented. It is based on
estimating the number of dangerous events associated with lightning
strikes. Proposed statistical description and the associated method
provide valuable information which could aid the design engineer in
optimising physical lengths of counterpoises in different grounding
arrangements and soil resistivity situations.
Abstract: Motion Tracking and Stereo Vision are complicated,
albeit well-understood problems in computer vision. Existing
softwares that combine the two approaches to perform stereo motion
tracking typically employ complicated and computationally expensive
procedures. The purpose of this study is to create a simple and
effective solution capable of combining the two approaches. The
study aims to explore a strategy to combine the two techniques
of two-dimensional motion tracking using Kalman Filter; and depth
detection of object using Stereo Vision. In conventional approaches
objects in the scene of interest are observed using a single camera.
However for Stereo Motion Tracking; the scene of interest is
observed using video feeds from two calibrated cameras. Using two
simultaneous measurements from the two cameras a calculation for
the depth of the object from the plane containing the cameras is made.
The approach attempts to capture the entire three-dimensional spatial
information of each object at the scene and represent it through a
software estimator object. In discrete intervals, the estimator tracks
object motion in the plane parallel to plane containing cameras and
updates the perpendicular distance value of the object from the plane
containing the cameras as depth. The ability to efficiently track
the motion of objects in three-dimensional space using a simplified
approach could prove to be an indispensable tool in a variety of
surveillance scenarios. The approach may find application from high
security surveillance scenes such as premises of bank vaults, prisons
or other detention facilities; to low cost applications in supermarkets
and car parking lots.
Abstract: The thyroid gland is the largest classic endocrine
organ that effects many organs of the body and plays a significant
role in the process of Metabolism in animals. The aim of this study
was to investigate the prevalence of thyroid disorders diagnosed by
ultrasound and microscopic Lesions of the thyroid during the
slaughter of apparently healthy One Humped Camels (Camelus
dromedarius) in Iran. Randomly, 520 male camels (With an age
range of 4 to 8 years), were studied in 2012 to 2013. The Camels’
thyroid glands were evaluated by sonographic examination. In both
longitudinal and transverse view and then tissue sections were
provide and stained with H & E and finally examined by light
microscopy. The results obtained indicated the following:
hyperplastic goiter (21%), degenerative changes (12%), follicular
cysts (8%), follicular atrophy (4%), nodular hyperplasia (3%),
adenoma (1%), carcinoma (1%) and simple goiter colloid (1%).
Ultrasound evaluation of thyroid gland in adenoma and carcinoma
showed enlargement and irregular of the gland, decreased
echogenicity, and the heterogeneous thyroid parenchyma. Also, in
follicular cysts were observed in the enlarged gland with no echo
structures of different sizes and decreased echogenicity as a local or
general. In nodular hyperplasia, increase echogenicity and
heterogeneous parenchymal were seen. These findings suggest the
use of sonography and pathology as a screening test in the diagnosis
of complications of thyroid disorders.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: Content-based image retrieval (CBIR) uses the
contents of images to characterize and contact the images. This paper
focus on retrieving the image by separating images into its three color
mechanism R, G and B and for that Discrete Wavelet Transformation
is applied. Then Wavelet based Generalized Gaussian Density (GGD)
is practical which is used for modeling the coefficients from the
wavelet transforms. After that it is agreed to Histogram of Oriented
Gradient (HOG) for extracting its characteristic vectors with Relevant
Feedback technique is used. The performance of this approach is
calculated by exactness and it confirms that this method is wellorganized
for image retrieval.
Abstract: Although it is not intended to identify distance
education students as a homogeneous group, recent research has
demonstrated that there are some demographic and personality
common traits among most of them that provide the basis for the
description of a typical distance learning student. The purpose of this
paper is to describe these common traits and to facilitate their
learning journey within a distance education program. The described
research is an initiative of the Distance Education Unit at the
European University Cyprus (Laureate International Universities) in
the context of its action for the improvement of the students’
performance.
Abstract: Batteries of electric vehicles (BEV) are becoming
more attractive with the advancement of new battery technologies
and promotion of electric vehicles. BEV batteries are recharged on
board vehicles using either the grid (G2V for Grid to Vehicle) or
renewable energies in a stand-alone application (H2V for Home to
Vehicle). This paper deals with the modeling, sizing and control of a
photovoltaic stand-alone application that can charge the BEV at
home. The modeling approach and developed mathematical models
describing the system components are detailed. Simulation and
experimental results are presented and commented.
Abstract: A thermosyphon system is a heat transfer loop which
operates on the basis of gravity and buoyancy forces. It guarantees a
good reliability and low maintenance cost as it does not involve any
mechanical pump. Therefore, it can be used in many industrial
applications such as refrigeration and air conditioning, electronic
cooling, nuclear reactors, geothermal heat extraction, etc. But flow
instabilities and loop configuration are the major problems in this
system. Several previous researchers studied that stabilities can be
suppressed by using nanofluids as loop fluid. In the present study a
rectangular thermosyphon loop with end heat exchangers are
considered for the study. This configuration is more appropriate for
many practical applications such as solar water heater, geothermal
heat extraction, etc. In the present work, steady-state analysis is
carried out on thermosyphon loop with parallel flow coaxial heat
exchangers at heat source and heat sink. In this loop nanofluid is
considered as the loop fluid and water is considered as the external
fluid in both hot and cold heat exchangers. For this analysis onedimensional
homogeneous model is developed. In this model,
conservation equations like conservation of mass, momentum, energy
are discretized using finite difference method. A computer code is
written in MATLAB to simulate the flow in thermosyphon loop. A
comparison in terms of heat transfer is made between water and
nanofluid as working fluids in the loop.
Abstract: In this paper, we propose a method for three-dimensional
(3-D)-model indexing based on defining a new
descriptor, which we call new descriptor using spherical harmonics.
The purpose of the method is to minimize, the processing time on the
database of objects models and the searching time of similar objects
to request object.
Firstly we start by defining the new descriptor using a new
division of 3-D object in a sphere. Then we define a new distance
which will be used in the search for similar objects in the database.
Abstract: Evaluating the performance of a simulator in the
CAVE has to be confirmed by encouraging people to live the
experience of virtual reality. In this paper, a detailed procedure of
recording video is presented. Limitations of the experimental device
are firstly exposed. Then, solutions for improving this idea are finally
described.
Abstract: Cloud computing (CC) has already gained overall
appreciation in research and practice. Whereas the willingness to
integrate cloud services in various IT environments is still unbroken,
the previous CC procurement processes run mostly in an unorganized
and non-standardized way. In practice, a sufficiently specific, yet
applicable business process for the important acquisition phase is
often lacking. And research does not appropriately remedy this
deficiency yet. Therefore, this paper introduces a field-tested
approach for CC procurement. Based on an extensive literature
review and augmented by expert interviews, we designed a model
that is validated and further refined through an in-depth real-life case
study. For the detailed process description, we apply the event-driven
process chain notation (EPC). The gained valuable insights into the
case study may help CC research to shift to a more socio-technical
area. For practice, next to giving useful organizational instructions
we will provide extended checklists and lessons learned.
Abstract: This paper proposed a silicon controller rectifier (SCR)
based ESD protection device to protect low voltage ESD for integrated
circuit. The proposed ESD protection device has low trigger voltage
and high holding voltage compared with conventional SCR-based
ESD protection devices. The proposed ESD protection circuit is
verified and compared by TCAD simulation. This paper verified
effective low voltage ESD characteristics with low trigger voltage of
5.79V and high holding voltage of 3.5V through optimization
depending on design variables (D1, D2, D3 and D4).
Abstract: In this study, we propose a novel technique for acoustic
echo suppression (AES) during speech recognition under barge-in
conditions. Conventional AES methods based on spectral subtraction
apply fixed weights to the estimated echo path transfer function
(EPTF) at the current signal segment and to the EPTF estimated until
the previous time interval. However, the effects of echo path changes
should be considered for eliminating the undesired echoes. We
describe a new approach that adaptively updates weight parameters in
response to abrupt changes in the acoustic environment due to
background noises or double-talk. Furthermore, we devised a voice
activity detector and an initial time-delay estimator for barge-in speech
recognition in communication networks. The initial time delay is
estimated using log-spectral distance measure, as well as
cross-correlation coefficients. The experimental results show that the
developed techniques can be successfully applied in barge-in speech
recognition systems.
Abstract: The purpose of this study is to examine the possible
link between employee and customer satisfaction. The service
provided by employees, help to build a good relationship with
customers and can help at increasing their loyalty. Published data for
job satisfaction and indicators of customer services of banks were
gathered from relevant published works which included data from
five different countries. The scores of customers and employees
satisfaction of the different published works were transformed and
normalized to the scale of 1 to 100. The data were analyzed and a
regression analysis of the two parameters was used to describe the
link between employee’s satisfaction and customer’s satisfaction.
Assuming that employee satisfaction has a significant influence on
customer’s service and the resulting customer satisfaction, the
reviewed data indicate that employee’s satisfaction contributes
significantly on the level of customer satisfaction in the Banking
sector. There was a significant correlation between the two
parameters (Pearson correlation R2=0.52 P