Abstract: This paper attempts to establish the fact that Multi
State Network Classification is essential for performance
enhancement of Transport protocols over Satellite based Networks. A
model to classify Multi State network condition taking into
consideration both congestion and channel error is evolved. In order
to arrive at such a model an analysis of the impact of congestion and
channel error on RTT values has been carried out using ns2. The
analysis results are also reported in the paper. The inference drawn
from this analysis is used to develop a novel statistical RTT based
model for multi state network classification.
An Adaptive Multi State Proactive Transport Protocol consisting
of Proactive Slow Start, State based Error Recovery, Timeout Action
and Proactive Reduction is proposed which uses the multi state
network state classification model. This paper also confirms through
detail simulation and analysis that a prior knowledge about the
overall characteristics of the network helps in enhancing the
performance of the protocol over satellite channel which is
significantly affected due to channel noise and congestion.
The necessary augmentation of ns2 simulator is done for
simulating the multi state network classification logic. This
simulation has been used in detail evaluation of the protocol under
varied levels of congestion and channel noise. The performance
enhancement of this protocol with reference to established protocols
namely TCP SACK and Vegas has been discussed. The results as
discussed in this paper clearly reveal that the proposed protocol
always outperforms its peers and show a significant improvement in
very high error conditions as envisaged in the design of the protocol.
Abstract: Urban non-point source (NPS) pollution for a
residential catchment in Miri, Sarawak was investigated for two storm events in 2011. Runoff from two storm events were sampled and tested for water quality parameters including TSS, BOD5, COD,
NH3-N, NO3-N, NO2-N, P and Pb. Concentration of the water quality
parameters was found to vary significantly between storms and the pollutant of concern was found to be NO3-N, TSS, COD and Pb. Results were compared to the Interim National Water Quality
Standards for Malaysia (INWQS),and the stormwater runoff from the
study can be classified as polluted, exceeding class III water quality,
especially in terms of TSS, COD, and NH3-N with maximum EMCs
of 158, 135, and 2.17 mg/L, respectively.
Abstract: This paper describes a complex energy signal model
that is isomorphic with digital human fingerprint images. By using
signal models, the problem of fingerprint matching is transformed
into the signal processing problem of finding a correlation between
two complex signals that differ by phase-rotation and time-scaling. A
technique for minutiae matching that is independent of image
translation, rotation and linear-scaling, and is resistant to missing
minutiae is proposed. The method was tested using random data
points. The results show that for matching prints the scaling and
rotation angles are closely estimated and a stronger match will have a
higher correlation.
Abstract: Macrobenthos distribution along the coastal waters of
Penang National Park was studid to estimate the effect of different
environmental parameters at three stations, during six sampling
months, from June 2010 to April 2011. The aim of this survey was to
investigate different environment stress over soft bottom polychaete
community along Teluk Ketapang and Pantai Acheh (Penang
National Park) over a year period. Variations in the polychaete
community were evaluated using univariate and multivariate
methods. A total of 604 individuals were examined which was
grouped into 23 families. Family Nereidae was the most abundant
(22.68%), followed by Spionidae (22.02%), Hesionidae (12.58%),
Nephtylidae (9.27%) and Orbiniidae (8.61%). It is noticeable that
good results can only be obtained on the basis of good taxonomic
resolution. The maximum Shannon-Wiener diversity (H'=2.16) was
recorded at distance 200m and 1200m (August 2010) in Teluk
Ketapang and lowest value of diversity was found at distance 1200m
(December 2010) in Teluk Ketapang.
Abstract: This paper presents the design of a ring-shaped tri-axial fore sensor that can be incorporated into the tip of a guidewire for use in minimally invasive surgery (MIS). The designed sensor comprises a ring-shaped structure located at the center of four cantilever beams. The ringdesign allows surgical tools to be easily passed through which largely simplified the integration process. Silicon nanowires (SiNWs) are used aspiezoresistive sensing elementsembeddedon the four cantilevers of the sensor to detect the resistance change caused by the applied load.An integration scheme with new designed guidewire tip structure having two coils at the distal end is presented. Finite element modeling has been employed in the sensor design to find the maximum stress location in order to put the SiNWs at the high stress regions to obtain maximum output. A maximum applicable force of 5 mN is found from modeling. The interaction mechanism between the designed sensor and a steel wire has been modeled by FEM. A linear relationship between the applied load on the steel wire and the induced stress on the SiNWs were observed.
Abstract: The clustering ensembles combine multiple partitions
generated by different clustering algorithms into a single clustering
solution. Clustering ensembles have emerged as a prominent method
for improving robustness, stability and accuracy of unsupervised
classification solutions. So far, many contributions have been done to
find consensus clustering. One of the major problems in clustering
ensembles is the consensus function. In this paper, firstly, we
introduce clustering ensembles, representation of multiple partitions,
its challenges and present taxonomy of combination algorithms.
Secondly, we describe consensus functions in clustering ensembles
including Hypergraph partitioning, Voting approach, Mutual
information, Co-association based functions and Finite mixture
model, and next explain their advantages, disadvantages and
computational complexity. Finally, we compare the characteristics of
clustering ensembles algorithms such as computational complexity,
robustness, simplicity and accuracy on different datasets in previous
techniques.
Abstract: In this study, the designed dual stage membrane
bioreactor (MBR) system was conceptualized for the treatment of
cyanide and heavy metals in electroplating wastewater. The design
consisted of a primary treatment stage to reduce the impact of
fluctuations and the secondary treatment stage to remove the residual
cyanide and heavy metal contaminants in the wastewater under
alkaline pH conditions. The primary treatment stage contained
hydrolyzed Citrus sinensis (C. sinensis) pomace and the secondary
treatment stage contained active Aspergillus awamori (A. awamori)
biomass, supplemented solely with C. sinensis pomace extract from
the hydrolysis process. An average of 76.37%, 95.37%, 93.26 and
94.76% and 99.55%, 99.91%, 99.92% and 99.92% degradation
efficiency for total cyanide (T-CN), including the sorption of nickel
(Ni), zinc (Zn) and copper (Cu) were observed after the first and
second treatment stages, respectively. Furthermore, cyanide
conversion by-products degradation was 99.81% and 99.75 for both
formate (CHOO-) and ammonium (NH4
+) after the second treatment
stage. After the first, second and third regeneration cycles of the C.
sinensis pomace in the first treatment stage, Ni, Zn and Cu removal
achieved was 99.13%, 99.12% and 99.04% (first regeneration cycle),
98.94%, 98.92% and 98.41% (second regeneration cycle) and 98.46
%, 98.44% and 97.91% (third regeneration cycle), respectively.
There was relatively insignificant standard deviation detected in all
the measured parameters in the system which indicated
reproducibility of the remediation efficiency in this continuous
system.
Abstract: Fixed-bed slow pyrolysis experiments of rice husk
have been conducted to determine the effect of pyrolysis
temperature, heating rate, particle size and reactor length on the
pyrolysis product yields. Pyrolysis experiments were performed at
pyrolysis temperature between 400 and 600°C with a constant
heating rate of 60°C/min and particle sizes of 0.60-1.18 mm. The
optimum process conditions for maximum liquid yield from the rice
husk pyrolysis in a fixed bed reactor were also identified. The highest
liquid yield was obtained at a pyrolysis temperature of 500°C,
particle size of
1.18-1.80 mm, with a heating rate of 60°C/min in a 300 mm length
reactor. The obtained yield of, liquid, gas and solid were found be in
the range of 22.57-31.78 %, 27.75-42.26 % and 34.17-42.52 % (all
weight basics) respectively at different pyrolysis conditions. The
results indicate that the effects of pyrolysis temperature and particle
size on the pyrolysis yield are more significant than that of heating
rate and reactor length. The functional groups and chemical
compositions present in the liquid obtained at optimum conditions
were identified by Fourier Transform-Infrared (FT-IR) spectroscopy
and Gas Chromatography/ Mass Spectroscopy (GC/MS) analysis
respectively.
Abstract: Steel corrosion in concrete is considered as a main
engineering problems for many countries and lots of expenses has been paid for their repair and maintenance annually. This problem
may occur in all engineering structures whether in coastal and offshore or other areas. Hence, concrete structures should be able to
withstand corrosion factors existing in water or soil. Reinforcing
steel corrosion enhancement can be measured by use of concrete
electrical resistance; and maintaining high electric resistivity in concrete is necessary for steel corrosion prevention. Lots of studies
devoted to different aspects of the subjects worldwide. In this paper, an evaluation of the effects of W/C ratio, cementitious materials, and
percent increase in silica fume were investigated on electric resistivity of high strength concrete. To do that, sixteen mix design
with one aggregate grading was planned. Five of them had varying amount of W/C ratio and other eleven mixes was prepared with
constant W/C ratio but different amount of cementitious materials.
Silica fume and super plasticizer were used with different proportions
in all specimens. Specimens were tested after moist curing for 28 days. A total of 80 cube specimens (50 mm) were tested for concrete
electrical resistance. Results show that concrete electric resistivity can be increased with increasing amount of cementitious materials
and silica fume.
Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.
Abstract: This work concerns the topological optimization
problem for determining the optimal petroleum refinery
configuration. We are interested in further investigating and
hopefully advancing the existing optimization approaches and
strategies employing logic propositions to conceptual process
synthesis problems. In particular, we seek to contribute to this
increasingly exciting area of chemical process modeling by
addressing the following potentially important issues: (a) how the
formulation of design specifications in a mixed-logical-and-integer
optimization model can be employed in a synthesis problem to enrich
the problem representation by incorporating past design experience,
engineering knowledge, and heuristics; and (b) how structural
specifications on the interconnectivity relationships by space (states)
and by function (tasks) in a superstructure should be properly
formulated within a mixed-integer linear programming (MILP)
model. The proposed modeling technique is illustrated on a case
study involving the alternative processing routes of naphtha, in which
significant improvement in the solution quality is obtained.
Abstract: The design requirements for successful human
accommodation in urban spaces are well known; and the range of
facilities available for meeting urban water quality and quantity
requirements is also well established. Their competing requirements
must be reconciled in order for urban spaces to be successful for
both. This paper outlines the separate human and water imperatives
and their interactions in urban spaces. Stormwater management
facilities- relative potential contributions to urban spaces are
contrasted, and design choices for achieving those potentials are
described. This study uses human success of urban space as the
evaluative criterion of stormwater amenity: human values call on
stormwater facilities to contribute to successful human spaces.
Placing water-s contribution under the overall idea of successful
urban space is an evolution from previous subjective evaluations.
The information is based on photographs and notes from
approximately 1,000 stormwater facilities and urban sites collected
during the last 35 years in North America and overseas, and the
author-s experience on multi-disciplinary design teams. This
conceptual study combines the disciplinary roles of engineering,
landscape architecture, and sociology in effecting successful urban
design.
Abstract: Unlike its conventional counterpart, Islamic principles
forbid Islamic banks to take any interest-related income and thus
makes deposits from depositors as an important source of fund for its
operational and financing. Consequently, the risk of deposit
withdrawal by depositors is an important aspect that should be wellmanaged
in Islamic banking. This paper aims to investigate factors
that influence depositors- withdrawal behavior in Islamic banks,
particularly in Malaysia, using the framework of theory of reasoned
action. A total of 368 respondents from Klang valley are involved in
the analysis. The paper finds that all the constructs variable i.e.
normative beliefs, subjective norms, behavioral beliefs, and attitude
towards behavior are perceived to be distinct by the respondents. In
addition, the structural equation model is able to verify the structural
relationships between subjective norms, attitude towards behavior
and behavioral intention. Subjective norms gives more influence to
depositors- decision on deposit withdrawal compared to attitude
towards behavior.
Abstract: A multi-board run-time reconfigurable (MRTR)
system for evolvable hardware (EHW) is introduced with the aim to
implement on hardware the bidirectional incremental evolution (BIE)
method. The main features of this digital intrinsic EHW solution rely
on the multi-board approach, the variable chromosome length
management and the partial configuration of the reconfigurable
circuit. These three features provide a high scalability to the solution.
The design has been written in VHDL with the concern of not being
platform dependant in order to keep a flexibility factor as high as
possible. This solution helps tackling the problem of evolving
complex task on digital configurable support.
Abstract: Determination of nano particle size is substantial since
the nano particle size exerts a significant effect on various properties
of nano materials. Accordingly, proposing non-destructive, accurate
and rapid techniques for this aim is of high interest. There are some
conventional techniques to investigate the morphology and grain size
of nano particles such as scanning electron microscopy (SEM),
atomic force microscopy (AFM) and X-ray diffractometry (XRD).
Vibrational spectroscopy is utilized to characterize different
compounds and applied for evaluation of the average particle size
based on relationship between particle size and near infrared spectra
[1,4] , but it has never been applied in quantitative morphological
analysis of nano materials. So far, the potential application of nearinfrared
(NIR) spectroscopy with its ability in rapid analysis of
powdered materials with minimal sample preparation, has been
suggested for particle size determination of powdered
pharmaceuticals. The relationship between particle size and diffuse
reflectance (DR) spectra in near infrared region has been applied to
introduce a method for estimation of particle size. Back propagation
artificial neural network (BP-ANN) as a nonlinear model was applied
to estimate average particle size based on near infrared diffuse
reflectance spectra. Thirty five different nano TiO2 samples with
different particle size were analyzed by DR-FTNIR spectrometry and
the obtained data were processed by BP- ANN.
Abstract: The Japanese integrative approach to social systems
can be observed in supply chain management as well as in the
relationship between public and private sectors. Both the Lean
Production System and the Developmental State Model are
characterized by efforts towards the achievement of mutual goals,
resulting in initiatives for capacity building which emphasize the
system level. In Brazil, although organizations undertake efforts to
build capabilities at the individual and organizational levels, the
system level is being neglected. Fieldwork data confirmed the findings
of other studies in terms of the lack of integration in supply chain
management in the Brazilian automobile industry. Moreover, due to
the absence of an active role of the Brazilian state in its relationship
with the private sector, automakers are not fully exploiting the
opportunities in the domestic and regional markets. For promoting a
higher level of economic growth as well as to increase the degree of
spill-over of technologies and techniques, a more integrative approach
is needed.
Abstract: Societal security, continuity scenarios and methodological cycling approach explained in this article. Namely societal security organizational challenges ask implementation of international standards BS 25999-2 & global ISO 22300 which is a family of standards for business continuity management system. Efficient global organization system is distinguished of high entity´s complexity, connectivity & interoperability, having not only cooperative relations in a fact. Competing business have numerous participating ´enemies´, which are in apparent or hidden opponent and antagonistic roles with prosperous organization system, resulting to a crisis scene or even to a battle theatre. Organization business continuity scenarios are necessary for such ´a play´ preparedness, planning, management & overmastering in real environments.
Abstract: Data from 1731 Gentile di Puglia lambs, sired by 65 rams over a 5-year period were analyzed by a mixed model to estimate the variance components for heritability. The considered growth traits were: birth weight (BW), weight at 30 days of age (W30) and average daily gain from birth to 30 days of age (DG). Year of birth, sex of lamb, type of birth (single or twin), dam age at lambing and farm were significant sources of variation for all the considered growth traits. The average lamb weights were 3.85±0.16 kg at birth, 9.57±0.91 kg at 30 days of age and the average daily gain was 191±14 g. Estimates of heritability were 0.33±0.05, 0.41±0.06 and 0.16±0.05 respectively for the same traits. These values suggest there is a good opportunity to improve Gentile di Puglia lambs by selecting animals for growth traits.
Abstract: A new strain of Type A influenza virus can cause the
transmission of H1N1 virus. This virus can spread between the
people by coughing and sneezing. Because the people are always
movement, so this virus can be easily spread. In this study, we
construct the dynamical network model of H1N1 virus by separating
the human into five groups; susceptible, exposed, infectious,
quarantine and recovered groups. The movement of people between
houses (local level) is considered. The behaviors of solutions to our
dynamical model are shown for the different parameters.
Abstract: In this paper an alternative visualisation approach of
the wake behind different vehicle body shapes with simplified and
fully-detailed underbody has been proposed and analysed. This
allows for a more clear distinction among the different wake regions.
This visualisation is based on a transformation of the cartesian
coordinates of a chosen wake plane to polar coordinates, using as
filter velocities lower than the freestream. This transformation
produces a polar wake plot that enables the division and
quantification of the wake in a number of sections. In this paper,
local drag has been used to visualise the drag contribution of the flow
by the different sections. Visually, a balanced wake can be observed
by the concentric behaviour of the polar plots. Alternatively,
integration of the local drag of each degree section as a ratio of the
total local drag yields a quantifiable approach of the wake uniformity,
where different sections contribute equally to the local drag, with the
exception of the wheels.