Abstract: The Emergency Department of a medical center in
Taiwan cooperated to conduct the research. A predictive model of
triage system is contracted from the contract procedure, selection of
parameters to sample screening. 2,000 pieces of data needed for the
patients is chosen randomly by the computer. After three
categorizations of data mining (Multi-group Discriminant Analysis,
Multinomial Logistic Regression, Back-propagation Neural
Networks), it is found that Back-propagation Neural Networks can
best distinguish the patients- extent of emergency, and the accuracy
rate can reach to as high as 95.1%. The Back-propagation Neural
Networks that has the highest accuracy rate is simulated into the triage
acuity expert system in this research. Data mining applied to the
predictive model of the triage acuity expert system can be updated
regularly for both the improvement of the system and for education
training, and will not be affected by subjective factors.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: The primary objective of this paper was to construct a
“kinematic parameter-independent modeling of three-axis machine
tools for geometric error measurement" technique. Improving the
accuracy of the geometric error for three-axis machine tools is one of
the machine tools- core techniques. This paper first applied the
traditional method of HTM to deduce the geometric error model for
three-axis machine tools. This geometric error model was related to the
three-axis kinematic parameters where the overall errors was relative
to the machine reference coordinate system. Given that the
measurement of the linear axis in this model should be on the ideal
motion axis, there were practical difficulties. Through a measurement
method consolidating translational errors and rotational errors in the
geometric error model, we simplified the three-axis geometric error
model to a kinematic parameter-independent model. Finally, based on
the new measurement method corresponding to this error model, we
established a truly practical and more accurate error measuring
technique for three-axis machine tools.
Abstract: In this work a dual laser triangulation system is presented for fast building of 2.5D textured models of objects within a production line. This scanner is designed to produce data suitable for 3D completeness inspection algorithms. For this purpose two laser projectors have been used in order to considerably reduce the problem of occlusions in the camera movement direction. Results of reconstruction of electronic boards are presented, together with a comparison with a commercial system.
Abstract: The main goal of the study is to analyze all relevant properties of the electro hydraulic systems and based on that to make a proper choice of the neural network control strategy that may be used for the control of the mechatronic system. A combination of electronic and hydraulic systems is widely used since it combines the advantages of both. Hydraulic systems are widely spread because of their properties as accuracy, flexibility, high horsepower-to-weight ratio, fast starting, stopping and reversal with smoothness and precision, and simplicity of operations. On the other hand, the modern control of hydraulic systems is based on control of the circuit fed to the inductive solenoid that controls the position of the hydraulic valve. Since this circuit may be easily handled by PWM (Pulse Width Modulation) signal with a proper frequency, the combination of electrical and hydraulic systems became very fruitful and usable in specific areas as airplane and military industry. The study shows and discusses the experimental results obtained by the control strategy of neural network control using MATLAB and SIMULINK [1]. Finally, the special attention was paid to the possibility of neuro-controller design and its application to control of electro-hydraulic systems and to make comparative with other kinds of control.
Abstract: Chitosan is an attractive polysaccharide obtained by
deacetylation of an abundant natural biopolymer called chitin. Chitin
and chitosan are excellent materials. To improve the potential of
chitin and chitosan modification is needed. In the present study,
grafting of maleic acid on to chitosan by cerium ammonium nitrate in
acetic acid solution was investigated with use of a microwave and
reflux system. The grafted chitosan was characterized by using a
Fourier-transform infrared spectrometry. The solubility and swelling
behavior of grafted chitosans were determined in acetate buffer (pH
3.6), citrophosphate buffer (pH 5.6 and pH 7.0), and boric buffer (pH
9.2) solutions. The sample obtained by microwave system with use of
a chitosan/maleic anhydride/ceric ammonium nitrate 0.2/3.922/0.99
gram of raw material within 30 minute showed the maximum
swelling ratio (13.6) in boric buffer solution.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: The substrate heater designed for this investigation is a front side substrate heating system. It consists of 10 conventional tungsten halogen lamps and an aluminum reflector, total input electrical power of 5 kW. The substrate is heated by means of a radiation from conventional tungsten halogen lamps directed to the substrate through a glass window. This design allows easy replacement of the lamps and maintenance of the system. Within 2 to 6 minutes the substrate temperature reaches 500 to 830 C by varying the vertical distance between the glass window and the substrate holder. Moreover, the substrate temperature can be easily controlled by controlling the input power to the system. This design gives excellent opportunity to deposit many deferent films at deferent temperatures in the same deposition time. This substrate heater was successfully used for Chemical Vapor Deposition (CVD) of many thin films, such as Silicon, iron, etc.
Abstract: This paper presents anti-synchronization of chaos
between two different chaotic systems using active control method.
The proposed technique is applied to achieve chaos antisynchronization
for the Lü and Rössler dynamical systems.
Numerical simulations are implemented to verify the results.
Abstract: In the present article, a new method has been developed to enhance the application of equipment monitoring, which in turn results in improving condition-based maintenance economic impact in an automobile parts manufacturing factory. This study also describes how an effective software with a simple database can be utilized to achieve cost-effective improvements in maintenance performance. The most important results of this project are indicated here: 1. 63% reduction in direct and indirect maintenance costs. 2. Creating a proper database to analyse failures. 3. Creating a method to control system performance and develop it to similar systems. 4. Designing a software to analyse database and consequently create technical knowledge to face unusual condition of the system. Moreover, the results of this study have shown that the concept and philosophy of maintenance has not been understood in most Iranian industries. Thus, more investment is strongly required to improve maintenance conditions.
Abstract: In this paper we propose an intelligent agent approach
to control the electric power grid at a smaller granularity in order to
give it self-healing capabilities. We develop a method using the
influence model to transform transmission substations into
information processing, analyzing and decision making (intelligent
behavior) units. We also develop a wireless communication method
to deliver real-time uncorrupted information to an intelligent
controller in a power system environment. A combined networking
and information theoretic approach is adopted in meeting both the
delay and error probability requirements. We use a mobile agent
approach in optimizing the achievable information rate vector and in
the distribution of rates to users (sensors). We developed the concept
and the quantitative tools require in the creation of cooperating semiautonomous
subsystems which puts the electric grid on the path
towards intelligent and self-healing system.
Abstract: Traffic management in an urban area is highly facilitated by the knowledge of the traffic conditions in every street or highway involved in the vehicular mobility system. Aim of the paper is to propose a neuro-fuzzy approach able to compute the main parameters of a traffic system, i.e., car density, velocity and flow, by using the images collected by the web-cams located at the crossroads of the traffic network. The performances of this approach encourage its application when the traffic system is far from the saturation. A fuzzy model is also outlined to evaluate when it is suitable to use more accurate, even if more time consuming, algorithms for measuring traffic conditions near to saturation.
Abstract: In this paper, an algorithm for detecting and attenuating
puff noises frequently generated under the mobile environment is
proposed. As a baseline system, puff detection system is designed
based on Gaussian Mixture Model (GMM), and 39th Mel Frequency
Cepstral Coefficient (MFCC) is extracted as feature parameters. To
improve the detection performance, effective acoustic features for puff
detection are proposed. In addition, detected puff intervals are
attenuated by high-pass filtering. The speech recognition rate was
measured for evaluation and confusion matrix and ROC curve are used
to confirm the validity of the proposed system.
Abstract: The effect of porous medium on the capillary instability of a cylindrical interface in the presence of axial electric field has been investigated using viscous potential flow theory. In viscous potential flow, the viscous term in Navier-Stokes equation vanishes as
vorticity is zero but viscosity is not zero. Viscosity enters through normal stress balance in the viscous potential flow theory and tangential stresses are not considered. A dispersion relation that accounts for the growth of axisymmetric waves is derived and stability is discussed theoretically as well as numerically. Stability criterion is given by critical value of applied electric field as well as critical wave number. Various graphs have been drawn to show the effect of various physical parameters such as electric field, viscosity ratio, permittivity ratio on the stability of the system. It has been observed that the axial electric field and porous medium both have stabilizing effect on the stability of the system.
Abstract: This paper shows a new method for design of fuzzy observers for Takagi-Sugeno systems. The method is based on Linear matrix inequalities (LMIs) and it allows to insert H constraint into the design procedure. The speed of estimation can tuned be specification of a decay rate of the observer closed loop system. We discuss here also the influence of parametric uncertainties at the output control system stability.
Abstract: Solid waste can be considered as an urban burden or
as a valuable resource depending on how it is managed. To meet the
rising demand for energy and to address environmental concerns, a
conversion from conventional energy systems to renewable resources
is essential. For the sustainability of human civilization, an
environmentally sound and techno-economically feasible waste
treatment method is very important to treat recyclable waste. Several
technologies are available for realizing the potential of solid waste as
an energy source, ranging from very simple systems for disposing of
dry waste to more complex technologies capable of dealing with
large amounts of industrial waste. There are three main pathways for
conversion of waste material to energy: thermo chemical,
biochemical and physicochemical. This paper investigates the thermo
chemical conversion of solid waste for energy recovery. The
processes, advantages and dis-advantages of various thermo chemical
conversion processes are discussed and compared. Special attention
is given to Gasification process as it provides better solutions
regarding public acceptance, feedstock flexibility, near-zero
emissions, efficiency and security. Finally this paper presents
comparative statements of thermo chemical processes and introduces
an integrated waste management system.
Abstract: Many applications of speech communication and speaker
identification suffer from the problem of co-channel speech. This
paper deals with a multi-resolution dyadic wavelet transform method
for usable segments of co-channel speech detection that could be
processed by a speaker identification system. Evaluation of this
method is performed on TIMIT database referring to the Target to
Interferer Ratio measure. Co-channel speech is constructed by
mixing all possible gender speakers. Results do not show much
difference for different mixtures. For the overall mixtures 95.76% of
usable speech is correctly detected with false alarms of 29.65%.
Abstract: In this paper, the process of obtaining Q and R
matrices for optimal pitch aircraft control system has been described.
Since the innovation of optimal control method, the determination of
Q and R matrices for such system has not been fully specified. The
value of Q and R for optimal pitch aircraft control application, have
been simulated and calculated. The suitable results for Q and R have
been observed through the performance index (PI). If the PI is small
“enough", we would say the Q & R values are suitable for that
certain type of optimal control system. Moreover, for the same value
of PI, we could have different Q and R sets. Due to the rule-free
determination of Q and R matrices, a specific method is brought to
find out the rough value of Q and R referring to rather small value of
PI.
Abstract: The machining performance is determined by the
frequency characteristics of the machine-tool structure and the
dynamics of the cutting process. Therefore, the prediction of dynamic
vibration behavior of spindle tool system is of great importance for the
design of a machine tool capable of high-precision and high-speed
machining. The aim of this study is to develop a finite element model
to predict the dynamic characteristics of milling machine tool and
hence evaluate the influence of the preload of the spindle bearings. To
this purpose, a three dimensional spindle bearing model of a high
speed engraving spindle tool was created. In this model, the rolling
interfaces with contact stiffness defined by Harris model were used to
simulate the spindle bearing components. Then a full finite element
model of a vertical milling machine was established by coupling the
spindle tool unit with the machine frame structure. Using this model,
the vibration mode that had a dominant influence on the dynamic
stiffness was determined. The results of the finite element simulations
reveal that spindle bearing with different preloads greatly affect the
dynamic behavior of the spindle tool unit and hence the dynamic
responses of the vertical column milling system. These results were
validated by performing vibration on the individual spindle tool unit
and the milling machine prototype, respectively. We conclude that
preload of the spindle bearings is an important component affecting
the dynamic characteristics and machining performance of the entire
vertical column structure of the milling machine.
Abstract: For controlling urban transportations, traffic lights
show similar behavior for different kinds of vehicles at intersections.
Emergency vehicles need special behavior at intersections, so traffic
lights should behave in different manner when emergency vehicles
approach them. At the present time, intelligent traffic lights control
urban transportations intelligently. In this paper the ethical aspect of
this topic is considered. A model is proposed for adding special
component to emergency vehicles and traffic lights for controlling
traffic in ethical manner. The proposed model is simulated by JADE.