Abstract: This paper presents an analysis of the localization accuracy of indoor positioning systems using Cramer-s rule via IEEE 802.15.4 wireless sensor networks. The objective is to study the impact of the methods used to convert the received signal strength into the distance that is used to compute the object location in the wireless indoor positioning system. Various methods were tested and the localization accuracy was analyzed. The experimental results show that the method based on the empirical data measured in the non line-of-sight (NLOS) environment yield the highest localization accuracy; with the minimum error distance less than 3 m.
Abstract: In this paper, a residue number arithmetic is used in
direct sequence spread spectrum system, this system is evaluated and
the bit error probability of this system is compared to that of non
residue number system. The effect of channel bandwidth, PN
sequences, multipath effect and modulation scheme are studied. A
Matlab program is developed to measure the signal-to-noise ratio
(SNR), and the bit error probability for the various schemes.
Abstract: In this paper we present simulation results for the
application of a bandwidth efficient algorithm (mapping algorithm)
to an image transmission system. This system considers three
different real valued transforms to generate energy compact
coefficients. First results are presented for gray scale and color image
transmission in the absence of noise. It is seen that the system
performs its best when discrete cosine transform is used. Also the
performance of the system is dominated more by the size of the
transform block rather than the number of coefficients transmitted or
the number of bits used to represent each coefficient. Similar results
are obtained in the presence of additive white Gaussian noise. The
varying values of the bit error rate have very little or no impact on
the performance of the algorithm. Optimum results are obtained for
the system considering 8x8 transform block and by transmitting 15
coefficients from each block using 8 bits.
Abstract: This paper deals with the application of Principal Component Analysis (PCA) and the Hotelling-s T2 Chart, using data collected from a drinking water treatment process. PCA is applied primarily for the dimensional reduction of the collected data. The Hotelling-s T2 control chart was used for the fault detection of the process. The data was taken from a United Utilities Multistage Water Treatment Works downloaded from an Integrated Program Management (IPM) dashboard system. The analysis of the results show that Multivariate Statistical Process Control (MSPC) techniques such as PCA, and control charts such as Hotelling-s T2, can be effectively applied for the early fault detection of continuous multivariable processes such as Drinking Water Treatment. The software package SIMCA-P was used to develop the MSPC models and Hotelling-s T2 Chart from the collected data.
Abstract: We consider a single-echelon, single-item inventory
system where both demand and lead-time are stochastic. Continuous
review policy is used to control the inventory system. The objective
is to calculate the reorder point level under stochastic parameters. A
case study is presented in Neonatal Intensive Care Unit.
Abstract: In this study, shaking table tests are performed to investigate the behavior of excess pore water pressure in different soft soil-foundations of soil-structure interaction (SSI) system. The variation of the behaviors under cycled minor shock is observed. Moreover, The generation and variation mechanism of excess pore water pressure under earthquake excitation in different soft soilfoundations are analyzed and discussed.
Abstract: In this study, a Loop Back Algorithm for component
connected labeling for detecting objects in a digital image is
presented. The approach is using loop back connected component
labeling algorithm that helps the system to distinguish the object
detected according to their label. Deferent than whole window
scanning technique, this technique reduces the searching time for
locating the object by focusing on the suspected object based on
certain features defined. In this study, the approach was also
implemented for a face detection system. Face detection system is
becoming interesting research since there are many devices or
systems that require detecting the face for certain purposes. The input
can be from still image or videos, therefore the sub process of this
system has to be simple, efficient and accurate to give a good result.
Abstract: This paper describes a practical approach to design
and develop a hybrid learning with acceleration feedback control
(HLC) scheme for input tracking and end-point vibration suppression
of flexible manipulator systems. Initially, a collocated proportionalderivative
(PD) control scheme using hub-angle and hub-velocity
feedback is developed for control of rigid-body motion of the system.
This is then extended to incorporate a further hybrid control scheme
of the collocated PD control and iterative learning control with
acceleration feedback using genetic algorithms (GAs) to optimize the
learning parameters. Experimental results of the response of the
manipulator with the control schemes are presented in the time and
frequency domains. The performance of the HLC is assessed in terms
of input tracking, level of vibration reduction at resonance modes and
robustness with various payloads.
Abstract: This paper presents the vibrations suppression of a thermoelastic beam subject to sudden heat input by a distributed piezoelectric actuators. An optimization problem is formulated as the minimization of a quadratic functional in terms of displacement and velocity at a given time and with the least control effort. The solution method is based on a combination of modal expansion and variational approaches. The modal expansion approach is used to convert the optimal control of distributed parameter system into the optimal control of lumped parameter system. By utilizing the variational approach, an explicit optimal control law is derived and the determination of the corresponding displacement and velocity is reduced to solving a set of ordinary differential equations.
Abstract: We demonstrate a nonfaradaic electrochemical impedance spectroscopy measurement of biochemically modified gold plated electrodes using a two-electrode system. The absence of any redox indicator in the impedance measurements provide more precise and accurate characterization of the measured bioanalyte at molecular resolution. An equivalent electrical circuit of the electrodeelectrolyte interface was deduced from the observed impedance data of saline solution at low and high concentrations. The detection of biomolecular interactions was fundamentally correlated to electrical double-layer variation at modified interface. The investigations were done using 20mer deoxyribonucleic acid (DNA) strands without any label. Surface modification was performed by creating mixed monolayer of the thiol-modified single-stranded DNA and a spacer thiol (mercaptohexanol) by a two-step self-assembly method. The results clearly distinguish between the noncomplementary and complementary hybridization of DNA, at low frequency region below several hundreds Hertz.
Abstract: The impact of OO design on software quality
characteristics such as defect density and rework by mean of
experimental validation. Encapsulation, inheritance, polymorphism,
reusability, Data hiding and message-passing are the major attribute
of an Object Oriented system. In order to evaluate the quality of an
Object oriented system the above said attributes can act as indicators.
The metrics are the well known quantifiable approach to express any
attribute. Hence, in this paper we tried to formulate a framework of
metrics representing the attributes of object oriented system.
Empirical Data is collected from three different projects based on
object oriented paradigms to calculate the metrics.
Abstract: Based on the component approach, three kinds of
dynamic load models, including a single –motor model, a two-motor
model and composite load model have been developed for the
stability studies of Khuzestan power system. The study results are
presented in this paper. Voltage instability is a dynamic phenomenon
and therefore requires dynamic representation of the power system
components. Industrial loads contain a large fraction of induction
machines. Several models of different complexity are available for
the description investigations. This study evaluates the dynamic
performances of several dynamic load models in combination with
the dynamics of a load changing transformer. Case study is steel
industrial substation in Khuzestan power systems.
Abstract: The electromagnetic spectrum is a natural resource
and hence well-organized usage of the limited natural resources is the
necessities for better communication. The present static frequency
allocation schemes cannot accommodate demands of the rapidly
increasing number of higher data rate services. Therefore, dynamic
usage of the spectrum must be distinguished from the static usage to
increase the availability of frequency spectrum. Cognitive radio is not
a single piece of apparatus but it is a technology that can incorporate
components spread across a network. It offers great promise for
improving system efficiency, spectrum utilization, more effective
applications, reduction in interference and reduced complexity of
usage for users. Cognitive radio is aware of its environmental,
internal state, and location, and autonomously adjusts its operations
to achieve designed objectives. It first senses its spectral environment
over a wide frequency band, and then adapts the parameters to
maximize spectrum efficiency with high performance. This paper
only focuses on the analysis of Bit-Error-Rate in cognitive radio by
using Particle Swarm Optimization Algorithm. It is theoretically as
well as practically analyzed and interpreted in the sense of
advantages and drawbacks and how BER affects the efficiency and
performance of the communication system.
Abstract: Thirty six samples from each (aerobic and anoxic)
activated sludge were collected from two wastewater treatment plants
with MBRs in Berlin, Germany. The samples were prepared for count
and definition of fungal isolates; these isolates were purified by
conventional techniques and identified by microscopic examination.
Sixty tow species belonging to 28 genera were isolated from
activated sludge samples under aerobic conditions (28 genera and 58
species) and anoxic conditions (26 genera and 52 species). The
obtained data show that, Aspergillus was found at 94.4% followed by
Penicillium 61.1 %, Fusarium (61.1 %), Trichoderma (44.4 %) and
Geotrichum candidum (41.6 %) species were the most prevalent in all
activated sludge samples. The study confirmed that fungi can thrive
in activated sludge and sporulation, but isolated in different numbers
depending on the effect of aeration system. Some fungal species in
our study are saprophytic, and other a pathogenic to plants and
animals.
Abstract: As the demand and prices of various petroleum products have been on the rise in recent years, there is a growing need for alternative fuels. Biodiesel, which consists of alkyl monoesters of fatty acids from vegetable oils and animal fats, is considered as an alternative to petroleum diesel. Biodiesel has comparable performance with that of diesel and has lower brake specific fuel consumption than diesel with significant reduction in emissions of CO, hydrocarbons (HC) and smoke with however, a slight increase in NOx emissions. This paper analyzes the effect of cooled exhaust gas recirculation in the combustion characteristics of a direct injection compression ignition engine using biodiesel blended fuel as opposed to the conventional system. The combustion parameters such as cylinder pressure, heat release rate, delay period and peak pressure were analyzed at various loads. The maximum cylinder pressure reduces as the fraction of biodiesel increases in the blend the maximum rate of pressure rise was found to be higher for diesel at higher engine loads.
Abstract: Currently, one of the main directions is developing of
development based on the clustering of economic operations of
Kazakhstan, providing for the organization and concentration of
production capacity in one region or the most optimal system. In the
modern economic literature clustering is regarded as one of the most
effective tools to ensure competitive businesses, and improve their
business itself.
Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: Integrated Total Quality Management (TQM) with
Lean Manufacturing (LM) is a system comprises of TQM with LM
principles and is associated with financial and nonfinancial
performance measurement indicators. The ultimate goal of this
system is to focus on achieving total customer satisfaction by
removing eight wastes available in any process in an organization.
A survey questionnaire was developed and distributed to 30 highly
active automotive vendors in Malaysia and analyzed by PASW
Statistics 18. It was found out that these vendors have been
practicing and measuring the effectiveness TQM and LM
implementation. More involvement of all Malaysian automotive
vendors will represent the exact status of current Malaysian
automotive industry in implementing TQM and LM and can
determine whether the industry is ready for integrated TQM and
LM system. This is the first study that combined 4 awards
practices, ISO/TS16949, Toyota Production System and
SAEJ4000.
Abstract: The purpose of this study is to identify and evaluate
the scale of implementation of Just-In-Time (JIT) in the different industrial sectors in the Middle East. This study analyzes the empirical data collected by a questionnaire survey distributed to
companies in three main industrial sectors in the Middle East, which
are: food, chemicals and fabrics. The following main hypotheses is formulated and tested: (The requirements of JIT application differ
according to the type of industrial sector).Descriptive statistics and Box plot analysis were used to examine the hypotheses. This study indicates a reasonable evidence for accepting the main hypotheses. It
reveals that there is no standard way to adopt JIT as a production system. But each industrial sector should concentrate in the
investment on critical requirements that differ according to the nature
and strategy of production followed in that sector.
Abstract: Inconel718 has been widely used as a super alloy in aerospace application due to the high strength at elevated temperatures, satisfactory oxidation resistance and heat corrosion resistance. In this study, the Inconel718 has been fabricated using high technology of Metal Injection Molding (MIM) process due to the cost effective technique for producing small, complex and precision parts in high volume compared with conventional method through machining. Through MIM, the binder system is one of the most important criteria in order to successfully fabricate the Inconel718. Even though, the binder system is a temporary, but failure in the selection and removal of the binder system will affect on the final properties of the sintered parts. Therefore, the binder system based on palm oil derivative which is palm stearin has been formulated and developed to replace the conventional binder system. The rheological studies of the mixture between the powder and binders system have been determined properly in order to be successful during injection into injection molding machine. After molding, the binder holds the particles in place. The binder system has to be removed completely through debinding step. During debinding step, solvent debinding and thermal pyrolysis has been used to remove completely of the binder system. The debound part is then sintered to give the required physical and mechanical properties. The results show that the properties of the final sintered parts fulfill the Standard Metal Powder Industries Federation (MPIF) 35 for MIM parts.