Abstract: An experimental investigation was conducted to study the effect of surface roughness on friction factor and heat transfer characteristics in single-phase fluid flow in a stainless steel micro-tube having diameter of 0.85 mm and average internal surface roughness of 1.7 μm with relative surface roughness of 0.002. Distilled water and R134a liquids were used as the working fluids and testing was conducted with Reynolds numbers ranging from 100 to 10,000 covering laminar, transition and turbulent flow conditions. The experiments were conducted with the micro-tube oriented horizontally with uniform heat fluxes applied at the test section. The results indicated that the friction factor of both water and R134a can be predicted by the Hagen-Poiseuille equation for laminar flow and the modified Miller correlation for turbulent flow and early transition from laminar to turbulent flows. The heat transfer results of water and R134a were in good agreement with the conventional theory in the laminar flow region and lower than the Adam’s correlation for turbulent flow region which deviates from conventional theory.
Abstract: This paper presents CMOS Current Mode Logic (CML) circuits for a high speed Digital to Analog Converter (DAC) using standard CMOS 65nm process. The CML circuits have the propagation delay advantage over its conventional CMOS counterparts due to smaller output voltage swing and tunable bias current. The CML circuits proposed in this paper can achieve a maximum propagation delay of only 9.3ps, which can satisfy the stringent requirement for the 5 GHz high speed DAC application. Another advantage for CML circuits is its dynamic symmetry characteristic resulting in a reduction of an additional inverter. Simulation results show that the proposed CML circuits can operate from 1.08V to 1.3V with temperature ranging from -40 to +120°C.
Abstract: Human society, there are many uncertainties, such as economic growth rate forecast of the financial crisis, many scholars have, since the the Song Chissom two scholars in 1993 the concept of the so-called fuzzy time series (Fuzzy Time Series)different mode to deal with these problems, a previous study, however, usually does not consider the relevant variables selected and fuzzy process based solely on subjective opinions the fuzzy semantic discrete, so can not objectively reflect the characteristics of the data set, in addition to carrying outforecasts are often fuzzy rules as equally important, failed to consider the importance of each fuzzy rule. For these reasons, the variable selection (Factor Selection) through self-organizing map (Self-Organizing Map, SOM) and proposed high-end weighted multivariate fuzzy time series model based on fuzzy neural network (Fuzzy-BPN), and using the the sequential weighted average operator (Ordered Weighted Averaging operator, OWA) weighted prediction. Therefore, in order to verify the proposed method, the Taiwan stock exchange (Taiwan Stock Exchange Corporation) Taiwan Weighted Stock Index (Taiwan Stock Exchange Capitalization Weighted Stock Index, TAIEX) as experimental forecast target, in order to filter the appropriate variables in the experiment Finally, included in other studies in recent years mode in conjunction with this study, the results showed that the predictive ability of this study further improve.
Abstract: Due to side-peaks of autocorrelation function, the binary offset carrier (BOC) signal acquisition suffers from an ambiguity when one of the side-peaks is acquired. In this paper, we first analyze that the BOC autocorrelation is made up of the sum of subcorrelations, and then, remove the side-peaks causing the ambiguity by recombining the sub-correlations. The proposed scheme is shown to remove the side-peaks completely. From numerical results, it is confirmed that the proposed scheme outperforms the conventional schemes in terms of the receiver operating characteristic and mean acquisition time.
Abstract: Force sensor has been used as requisite for knowing information on the amount and the directions of forces on the skin surface. We have developed a four-degrees-of-freedom capacitive force sensor (approximately 20×20×5 mm3) that has a flexible structure and sixteen parallel plate capacitors. An iterative algorithm was developed for estimating four displacements from the sixteen capacitances using fourth-order polynomial approximation of characteristics between capacitance and displacement. The estimation results from measured capacitances had large error caused by deterioration of the characteristics. In this study, effective capacitors had major information were selected on the basis of the capacitance change range and the characteristic shape. Maximum errors in calibration and non-calibration points were 25%and 6.8%.However the maximum error was larger than desired value, the smallness of averaged value indicated the occurrence of a few large error points. On the other hand, error in non-calibration point was within desired value.
Abstract: Different vegetable oil based biodiesel (FAMES) were prepared by alkaline transesterification using refined oils as well as waste frying oil (WFO). Methanol and sodium hydroxide are used as catalyst under similar reaction conditions. To ensure the quality of biodiesel produced, a series of different ASTM Standard tests were carried out. In this context, various testwere done including viscosity, carbon residue, specific gravity, corrosion test, flash point, cloud point and pour point. Results revealed that characteristics of biodiesel depend on the feedstock and it is far better than petroleum diesel.
Abstract: In this paper we use low frequency noise analysis to understand and map the current conduction path in a multi gate junctionless FinFET. The device used in this study behaves as a gated resistor and shows excellent short channel effect suppression due to its multi gate structure. Generally for a bulk conduction device like the junctionless device studied in this work, the low frequency noise can be modelled using the mobility fluctuation model; however for this device we can also see the effect of carrier fluctuations on the LFN characteristic. The noise characteristic at different gate bias and also the possible location of the traps is explained.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: The electrical power systems of aircrafts have made
serious progress in recent years because the aircrafts depend more
and more on the electricity. There is a trend in the aircraft industry to
replace hydraulic and pneumatic systems with electrical systems,
achieving more comfort and monitoring features and enlarging the
energetic efficiency. Thus, was born the concept More Electric
Aircraft. In this paper is analyzed the integration of a fuel cell into
the existing electrical generation and distribution systems of an
aircraft. The dynamic characteristics of fuel cell systems necessitate
an adaptation of the electrical power system. The architecture studied
in this paper consists of a 50kW fuel cell, a dc to dc converter and
several loads. The dc to dc converter is used to step down the fuel
cell voltage from about 625Vdc to 28Vdc.
Abstract: MOSCAPs of various combinations of Hafnium
oxide and Titanium oxide of varying thickness with Aluminum as gate electrode have been fabricated and electrically characterized.
The effects of voltage stress on the I-V characteristics for prolonged time durations have been studied and compared. Results showed
hard breakdown and negligible degradation of reliability under stress.
Abstract: Absorption spectra of infra-red (IR) radiation of the
disperse water medium absorbing the most important greenhouse
gases: CO2 , N2O , CH4 , C2H2 , C2H6 have been calculated by
the molecular dynamics method. Loss of the absorbing ability at the
formation of clusters due to a reduction of the number of centers
interacting with IR radiation, results in an anti-greenhouse effect.
Absorption of O3 molecules by the (H2O)50 cluster is investigated
at its interaction with Cl- ions. The splitting of ozone molecule on
atoms near to cluster surface was observed. Interaction of water
cluster with Cl- ions causes the increase of integrated intensity of
emission spectra of IR radiation, and also essential reduction of the
similar characteristic of Raman spectrum. Relative integrated
intensity of absorption of IR radiation for small water clusters was
designed. Dependences of the quantity of weight on altitude for
vapor of monomers, clusters, droplets, crystals and mass of all
moisture were determined. The anti-greenhouse effect of clusters was
defined as the difference of increases of average global temperature
of the Earth, caused by absorption of IR radiation by free water
molecules forming clusters, and absorption of clusters themselves.
The greenhouse effect caused by clusters makes 0.53 K, and the antigreenhouse
one is equal to 1.14 K. The increase of concentration of
CO2 in the atmosphere does not always correlate with the
amplification of greenhouse effect.
Abstract: The mathematical equation for Separation of the
binary aqueous solution is developed by using the Spiegler- Kedem
theory. The characteristics of a B-9 hollow fibre module of Du Pont
are determined by using these equations and their results are
compared with the experimental results of Ohya et al. The agreement
between these results is found to be excellent.
Abstract: Short-Term Load Forecasting (STLF) plays an important role for the economic and secure operation of power systems. In this paper, Continuous Genetic Algorithm (CGA) is employed to evolve the optimum large neural networks structure and connecting weights for one-day ahead electric load forecasting problem. This study describes the process of developing three layer feed-forward large neural networks for load forecasting and then presents a heuristic search algorithm for performing an important task of this process, i.e. optimal networks structure design. The proposed method is applied to STLF of the local utility. Data are clustered due to the differences in their characteristics. Special days are extracted from the normal training sets and handled separately. In this way, a solution is provided for all load types, including working days and weekends and special days. We find good performance for the large neural networks. The proposed methodology gives lower percent errors all the time. Thus, it can be applied to automatically design an optimal load forecaster based on historical data.
Abstract: The problems with high complexity had been the challenge in combinatorial problems. Due to the none-determined and polynomial characteristics, these problems usually face to unreasonable searching budget. Hence combinatorial optimizations attracted numerous researchers to develop better algorithms. In recent academic researches, most focus on developing to enhance the conventional evolutional algorithms and facilitate the local heuristics, such as VNS, 2-opt and 3-opt. Despite the performances of the introduction of the local strategies are significant, however, these improvement cannot improve the performance for solving the different problems. Therefore, this research proposes a meta-heuristic evolutional algorithm which can be applied to solve several types of problems. The performance validates BBEA has the ability to solve the problems even without the design of local strategies.
Abstract: The present work involves measurements to examine
the effects of initial conditions on aerodynamic and acoustic
characteristics of a Jet at M=0.8 by changing the orientation of sharp
edged orifice plate. A thick plate with chamfered orifice presented divergent and convergent openings when it was flipped over. The centerline velocity was found to decay more rapidly for divergent
orifice and that was consistent with the enhanced mass entrainment
suggesting quicker spread of the jet compared with that from the convergent orifice. The mixing layer region elucidated this effect of
initial conditions at an early stage – the growth was found to be comparatively more pronounced for the divergent orifice resulting in
reduced potential core size. The acoustic measurements, carried out in the near field noise region outside the jet within potential core
length, showed the jet from the divergent orifice to be less noisy. The frequency spectra of the noise signal exhibited that in the initial
region of comparatively thin mixing layer for the convergent orifice,
the peak registered a higher SPL and a higher frequency as well. The noise spectra and the mixing layer development suggested a direct correlation between the coherent structures developing in the initial
region of the jet and the noise captured in the surrounding near field.
Abstract: Brushless DC motor with high torque density and slim
topology for easy loading for robot system is proposed and
manufactured. Electromagnetic design is executed by equivalent
magnetic circuit model and numerical analysis. Manufactured motor is
tested and verified characteristics comparing with conventional BLDC
motor.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally
graded materials (FGMs) composed of stainless steel and
nickel is presented. Material properties vary along the
thickness direction of the shell according to volume fraction
power law. The cylindrical shells have ring supports which are
arbitrarily placed along the shell and impose zero lateral
deflections. The study is carried out based on third order shear
deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: The national economy development affects the vehicle
ownership which ultimately increases fuel consumption. The rise of
the vehicle ownership is dominated by the increasing number of
motorcycles. This research aims to analyze and identify the
characteristics of fuel consumption, the city transportation system,
and to analyze the relationship and the effect of the city
transportation system on the fuel consumption. A multivariable
analysis is used in this study. The data analysis techniques include: a
Multivariate Multivariable Analysis by using the R software. More
than 84% of fuel on Java is consumed in metropolitan and large
cities. The city transportation system variables that strongly effect the
fuel consumption are population, public vehicles, private vehicles and
private bus. This method can be developed to control the fuel
consumption by considering the urban transport system and city
tipology. The effect can reducing subsidy on the fuel consumption,
increasing state economic.
Abstract: In this paper a novel ultra-wideband (UWB) slot antenna with band notch characteristics for world interoperability for microwave access (WiMAX) is proposed. The designed antenna consists of a rectangular radiating patch and a ground plane with tapered shape slot. To realize a notch band, a curved parasitic element has been etched out along with the radiating patch. It is observed that by adjusting the length, thickness and position of the parasitic element, the proposed antenna can achieved an impedance bandwidth of 8.01GHz (2.84 to 10.85GHz) with a notched band of 3.28-3.85GHz. Compared to the recently reported band notch antennas, the proposed antenna has a simple configuration to realize band notch characteristics in order to mitigate the potential interference between WiMAX and UWB system. Furthermore, a stable radiation pattern and moderate gain except at the notched band makes the proposed antenna suitable for various UWB applications.
Abstract: The conventional assessment of human semen is a
highly subjective assessment, with considerable intra- and interlaboratory
variability. Computer-Assisted Sperm Analysis (CASA)
systems provide a rapid and automated assessment of the sperm
characteristics, together with improved standardization and quality
control. However, the outcome of CASA systems is sensitive to the
method of experimentation. While conventional CASA systems use
digital microscopes with phase-contrast accessories, producing
higher contrast images, we have used raw semen samples (no
staining materials) and a regular light microscope, with a digital
camera directly attached to its eyepiece, to insure cost benefits and
simple assembling of the system. However, since the accurate finding
of sperms in the semen image is the first step in the examination and
analysis of the semen, any error in this step can affect the outcome of
the analysis. This article introduces and explains an algorithm for
finding sperms in low contrast images: First, an image enhancement
algorithm is applied to remove extra particles from the image. Then,
the foreground particles (including sperms and round cells) are
segmented form the background. Finally, based on certain features
and criteria, sperms are separated from other cells.