Abstract: This paper focuses on a variational formulation of large amplitude free vibration behavior of a very sag marine cable. In the static equilibrium state, the marine cable has a very large sag configuration. In the motion state, the marine cable is assumed to vibrate in in-plane motion with large amplitude from the static equilibrium position. The total virtual work-energy of the marine cable at the dynamic state is formulated which involves the virtual strain energy due to axial deformation, the virtual work done by effective weight, and the inertia forces. The equations of motion for the large amplitude free vibration of marine cable are obtained by taking into account the difference between the Euler’s equation in the static state and the displaced state. Based on the Galerkin finite element procedure, the linear and nonlinear stiffness matrices, and mass matrices of the marine cable are obtained and the eigenvalue problem is solved. The natural frequency spectrum and the large amplitude free vibration behavior of marine cable are presented.
Abstract: The monitoring of spectrum usage and signal identification, using cognitive radio, is done to identify frequencies that are vacant for reuse. It has been established that ‘internet of things’ device uses secondary frequency which is free, thereby facing the challenge of interference from other users, where some primary frequencies are not being utilised. The design was done by analysing a specific frequency spectrum, checking if all the frequency stations that range from 87.5-108 MHz are presently being used in Benin City, Edo State, Nigeria. From the results, it was noticed that by using Software Defined Radio/Simulink, we were able to identify vacant frequencies in the range of frequency under consideration. Also, we were able to use the significance of energy detection threshold to reuse this vacant frequency spectrum, when the cognitive radio displays a zero output (that is decision H0), meaning that the channel is unoccupied. Hence, the analysis was able to find the spectrum hole and identify how it can be reused.
Abstract: Prestressed concrete is used a lot in infrastructures such as roads or bridges. However, poor grout filling and PC steel corrosion are currently major issues of prestressed concrete structures. One of the problems with nondestructive corrosion detection of PC steel is a plastic pipe which covers PC steel. The insulative property of pipe makes a nondestructive diagnosis difficult; therefore a practical technology to detect these defects is necessary for the maintenance of infrastructures. The goal of the research is a development of an electrochemical technique which enables to detect internal defects from the surface of prestressed concrete nondestructively. Ideally, the measurements should be conducted from the surface of structural members to diagnose non-destructively. In the present experiment, a prestressed concrete member is simplified as a layered specimen to simulate a current path between an input and an output electrode on a member surface. The specimens which are layered by mortar and the prestressed concrete constitution materials (steel, polyethylene, stainless steel, or galvanized steel plates) were provided to the alternating current impedance measurement. The magnitude of an applied electric field was 0.01-volt or 1-volt, and the frequency range was from 106 Hz to 10-2 Hz. The frequency spectrums of impedance, which relate to charge reactions activated by an electric field, were measured to clarify the effects of the material configurations or the properties. In the civil engineering field, the Nyquist diagram is popular to analyze impedance and it is a good way to grasp electric relaxation using a shape of the plot. However, it is slightly not suitable to figure out an influence of a measurement frequency which is reciprocal of reaction time. Hence, Bode diagram is also applied to describe charge reactions in the present paper. From the experiment results, the alternating current impedance method looks to be applicable to the insulative material measurement and eventually prestressed concrete diagnosis. At the same time, the frequency spectrums of impedance show the difference of the material configuration. This is because the charge mobility reflects the variety of substances and also the measuring frequency of the electric field determines migration length of charges which are under the influence of the electric field. However, it could not distinguish the differences of the material thickness and is inferred the difficulties of prestressed concrete diagnosis to identify the amount of an air void or a layer of corrosion product by the technique.
Abstract: This paper presents two techniques, local feature
extraction using image spectrum and low frequency spectrum
modelling using GMM to capture the underlying statistical
information to improve the performance of face recognition
system. Local spectrum features are extracted using overlap sub
block window that are mapped on the face image. For each of this
block, spatial domain is transformed to frequency domain using
DFT. A low frequency coefficient is preserved by discarding high
frequency coefficients by applying rectangular mask on the
spectrum of the facial image. Low frequency information is non-
Gaussian in the feature space and by using combination of several
Gaussian functions that has different statistical properties, the best
feature representation can be modelled using probability density
function. The recognition process is performed using maximum
likelihood value computed using pre-calculated GMM components.
The method is tested using FERET datasets and is able to achieved
92% recognition rates.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: Photoacoustic imaging (PAI) is a non-invasive and
non-ionizing imaging modality that combines the absorption contrast
of light with ultrasound resolution. Laser is used to deposit optical
energy into a target (i.e., optical fluence). Consequently, the target
temperature rises, and then thermal expansion occurs that leads to
generating a PA signal. In general, most image reconstruction
algorithms for PAI assume uniform fluence within an imaging object.
However, it is known that optical fluence distribution within the
object is non-uniform. This could affect the reconstruction of PA
images. In this study, we have investigated the influence of optical
fluence distribution on PA back-propagation imaging using finite
element method. The uniform fluence was simulated as a triangular
waveform within the object of interest. The non-uniform fluence
distribution was estimated by solving light propagation within a
tissue model via Monte Carlo method. The results show that the PA
signal in the case of non-uniform fluence is wider than the uniform
case by 23%. The frequency spectrum of the PA signal due to the
non-uniform fluence has missed some high frequency components in
comparison to the uniform case. Consequently, the reconstructed
image with the non-uniform fluence exhibits a strong smoothing
effect.
Abstract: The present work involves measurements to examine
the effects of initial conditions on aerodynamic and acoustic
characteristics of a Jet at M=0.8 by changing the orientation of sharp
edged orifice plate. A thick plate with chamfered orifice presented divergent and convergent openings when it was flipped over. The centerline velocity was found to decay more rapidly for divergent
orifice and that was consistent with the enhanced mass entrainment
suggesting quicker spread of the jet compared with that from the convergent orifice. The mixing layer region elucidated this effect of
initial conditions at an early stage – the growth was found to be comparatively more pronounced for the divergent orifice resulting in
reduced potential core size. The acoustic measurements, carried out in the near field noise region outside the jet within potential core
length, showed the jet from the divergent orifice to be less noisy. The frequency spectra of the noise signal exhibited that in the initial
region of comparatively thin mixing layer for the convergent orifice,
the peak registered a higher SPL and a higher frequency as well. The noise spectra and the mixing layer development suggested a direct correlation between the coherent structures developing in the initial
region of the jet and the noise captured in the surrounding near field.
Abstract: Occurrence of a multiple-points fault in machine operations could result in exhibiting complex fault signatures, which could result in lowering fault diagnosis accuracy. In this study, a multiple-points defect model (MPDM) is proposed which can simulate fault signature-s dynamics for n-points bearing faults. Furthermore, this study identifies that in case of multiple-points fault in the rotary machine, the location of the dominant component of defect frequency shifts depending upon the relative location of the fault points which could mislead the fault diagnostic model to inaccurate detections. Analytical and experimental results are presented to characterize and validate the variation in the dominant component of defect frequency. Based on envelop detection analysis, a modification is recommended in the existing fault diagnostic models to consider the multiples of defect frequency rather than only considering the frequency spectrum at the defect frequency in order to incorporate the impact of multiple points fault.
Abstract: Laser Doppler flowmetry is a modern method of noninvasive
microcirculation investigation. The aim of our study was to
use this method in the examination of patients with secondary
lymphedema of the lower extremities and obliterating atherosclerosis
of lower extremities. In the analysis of the amplitude-frequency
spectrum of secondary lymphedema patients we have identified
remarkable changes. To describe the changes we used a special
amplitude rate. In both of patients groups this rate was significally
(p
Abstract: Rolling element bearings are widely used in industry,
especially where high load capacity is required. The diagnosis of
their conditions is essential matter for downtime reduction and saving
cost of maintenance. Therefore, an intensive analysis of frequency
spectrum of their faults must be carried out in order to determine the
main reason of the fault. This paper focus on a beating phenomena
observed in the waveform (time domain) of a cylindrical rolling
element bearing. The beating frequencies were not related to any
sources nearby the machine nor any other malfunctions (unbalance,
misalignment ...etc). More investigation on the spike energy and the
frequency spectrum indicated a problem with races of the bearing.
Multi-harmonics of the fundamental defects frequencies were
observed. Two of them were close to each other in magnitude those
were the source of the beating phenomena.
Abstract: In this paper, a technique is proposed to implement
an artificial voltage-controlled capacitance or inductance which can
replace the well-known varactor diode in many applications. The
technique is based on injecting the current of a voltage-controlled
current source onto a fixed capacitor or inductor. Then, by controlling
the transconductance of the current source by an external bias voltage,
a voltage-controlled capacitive or inductive reactance is obtained.
The proposed voltage-controlled reactance devices can be designed
to work anywhere in the frequency spectrum. Practical circuits for the
proposed voltage-controlled reactances are suggested and simulated.
Abstract: This paper describes a method of signal process applied
on an end effects of Hilbert-Huang transform (HHT) to provide an
improvement in the reality of spectrum. The method is based on
back-propagation network (BPN). To improve the effect, the end
extension of the original signal is obtained by back-propagation
network. A full waveform including origin and its extension is
decomposed by using empirical mode decomposition (EMD) to obtain
intrinsic mode functions (IMFs) of the waveform. Then, the Hilbert
transform (HT) is applied to the IMFs to obtain the Hilbert spectrum of
the waveform. As a result, the method is superiority of the processing
of end effect of HHT to obtain the real frequency spectrum of signals.
Abstract: The electromagnetic spectrum is a natural resource
and hence well-organized usage of the limited natural resources is the
necessities for better communication. The present static frequency
allocation schemes cannot accommodate demands of the rapidly
increasing number of higher data rate services. Therefore, dynamic
usage of the spectrum must be distinguished from the static usage to
increase the availability of frequency spectrum. Cognitive radio is not
a single piece of apparatus but it is a technology that can incorporate
components spread across a network. It offers great promise for
improving system efficiency, spectrum utilization, more effective
applications, reduction in interference and reduced complexity of
usage for users. Cognitive radio is aware of its environmental,
internal state, and location, and autonomously adjusts its operations
to achieve designed objectives. It first senses its spectral environment
over a wide frequency band, and then adapts the parameters to
maximize spectrum efficiency with high performance. This paper
only focuses on the analysis of Bit-Error-Rate in cognitive radio by
using Particle Swarm Optimization Algorithm. It is theoretically as
well as practically analyzed and interpreted in the sense of
advantages and drawbacks and how BER affects the efficiency and
performance of the communication system.
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: Worldwide many electrical equipment insulation
failures have been reported caused by switching operations, while
those equipments had previously passed all the standard tests and
complied with all quality requirements. The problem is mostly
associated with high-frequency overvoltages generated during
opening or closing of a switching device. The transients generated
during switching operations in a Gas Insulated Substation (GIS) are
associated with high frequency components in the order of few tens
of MHz.
The frequency spectrum of the VFTO generated in the 220/66 kV
Wadi-Hoff GIS is analyzed using Fast Fourier Transform technique.
The main frequency with high voltage amplitude due to the operation
of disconnector (DS5) is 5 to 10 MHz, with the highest amplitude at 9
MHz. The main frequency with high voltage amplitude due to the
operation of circuit breaker (CB5) is 1 to 25 MHz, with the highest
amplitude at 2 MHz.
Mitigating techniques damped the oscillating frequencies
effectively. The using of cable terminal reduced the frequency
oscillation effectively than that of OHTL terminal. The using of a
shunt capacitance results in vanishing the high frequency
components. Ferrite rings reduces the high frequency components
effectively especially in the range 2 to 7 MHz. The using of RC and
RL filters results in vanishing the high frequency components.
Abstract: A novel interpolation scheme to extend usable spectrum
and upconvert in high performance D/A converters is addressed in this
paper. By adjusting the pulse width of cycle and the production circuit
of code, the expansion code is a null code or complementary code that
is interpolation process. What the times and codes of interpolation
decide DAC works in one of a normal mode or multi-mixer mode
so that convert the input digital data signal into normal signal or a
mixed analog signal having a mixer frequency that is higher than the
data frequency. Simulation results show that the novel scheme and
apparatus most extend the usable frequency spectrum into fifth to
sixth Nyquist zone beyond conventional DACs.
Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.