Abstract: A novel design technique employing CMOS Current
Feedback Operational Amplifier (CFOA) is presented. The feature of
consumption very low power in designing pseudo-OTA is used to
decreasing the total power consumption of the proposed CFOA. This
design approach applies pseudo-OTA as input stage cascaded with
buffer stage. Moreover, the DC input offset voltage and harmonic
distortion (HD) of the proposed CFOA are very low values compared
with the conventional CMOS CFOA due to the symmetrical input
stage. P-Spice simulation results are obtained using 0.18μm MIETEC
CMOS process parameters and supply voltage of ±1.2V, 50μA
biasing current. The p-spice simulation shows excellent improvement
of the proposed CFOA over existing CMOS CFOA. Some of these
performance parameters, for example, are DC gain of 62. dB, openloop
gain bandwidth product of 108 MHz, slew rate (SR+) of
+71.2V/μS, THD of -63dB and DC consumption power (PC) of
2mW.
Abstract: The Trustworthy link failure recovery algorithm is
introduced in this paper, to provide the forwarding continuity even
with compound link failures. The ephemeral failures are common in
IP networks and it also has some proposals based on local rerouting.
To ensure forwarding continuity, we are introducing the compound
link failure recovery algorithm, even with compound link failures.
For forwarding the information, each packet carries a blacklist, which
is a min set of failed links encountered along its path, and the next
hop is chosen by excluding the blacklisted links. Our proposed
method describes how it can be applied to ensure forwarding to all
reachable destinations in case of any two or more link or node
failures in the network. After simulating with NS2 contains lot of
samples proved that the proposed protocol achieves exceptional
concert even under elevated node mobility using Trustworthy link
Failure Recovery Algorithm.
Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: This paper deals with the study of reflection and
transmission characteristics of acoustic waves at the interface of a
semiconductor half-space and elastic solid. The amplitude ratios
(reflection and transmission coefficients) of reflected and transmitted
waves to that of incident wave varying with the incident angles have
been examined for the case of quasi-longitudinal wave. The special
cases of normal and grazing incidence have also been derived with
the help of Gauss elimination method. The mathematical model
consisting of governing partial differential equations of motion and
charge carriers’ diffusion of n-type semiconductors and elastic solid
has been solved both analytically and numerically in the study. The
numerical computations of reflection and transmission coefficients
has been carried out by using MATLAB programming software for
silicon (Si) semiconductor and copper elastic solid. The computer
simulated results have been plotted graphically for Si
semiconductors. The study may be useful in semiconductors,
geology, and seismology in addition to surface acoustic wave (SAW)
devices.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Optical biosensors have become a powerful detection
and analysis tool for wide-ranging applications in biomedical research,
pharmaceuticals and environmental monitoring. This study carried out
the computational fluid dynamics (CFD)-based simulations to explore
the dispersion phenomenon in the micro channel of an optical
biosensor. The predicted time sequences of concentration contours
were utilized to better understand the dispersion development occurred
in different geometric shapes of micro channels. The simulation results
showed the surface concentrations at the sensing probe (with the best
performance of a grating coupler) in respect of time to appraise the
dispersion effect and therefore identify the design configurations
resulting in minimum dispersion.
Abstract: The objective of this study is to conduct computational
fluid dynamic (CFD) simulations for evaluating the cooling efficacy
from vegetation implanted in a public park in the Taipei, Taiwan. To
probe the impacts of park renewal by means of adding three pavilions
and supplementary green areas on urban microclimates, the simulated
results have revealed that the park having a higher percentage of green
coverage ratio (GCR) tended to experience a better cooling effect.
These findings can be used to explore the effects of different greening
modifications on urban environments for achieving an effective
thermal comfort in urban public spaces.
Abstract: The comprehensive CFD models have been used to
represent and study the heterogeneous combustion of biomass. In the
present work, the operation of a global flue gas circuit in the sugarcane
bagasse combustion, from wind boxes below primary air grate
supply, passing by bagasse insertion in swirl burners and boiler
furnace, to boiler bank outlet is simulated. It uses five different
meshes representing each part of this system located in sequence:
wind boxes and grate, boiler furnace, swirl burners, superheaters and
boiler bank. The model considers turbulence using standard k-ε,
combustion using EDM, radiation heat transfer using DTM with 16
ray directions and bagasse particle tracking represented by Schiller-
Naumann model. The results showed good agreement with expected
behavior found in literature and equipment design. The more detailed
results view in separated parts of flue gas system allows observing
some flow behaviors that cannot be represented by usual
simplifications like bagasse supply under homogeneous axial and
rotational vectors and others that can be represented using new
considerations like the representation of 26 thousand grate orifices by
144 rectangular inlets.
Abstract: We present a refined multiscale Shannon entropy for
analyzing electroencephalogram (EEG), which reflects the underlying
dynamics of EEG over multiple scales. The rationale behind
this method is that neurological signals such as EEG possess
distinct dynamics over different spectral modes. To deal with the
nonlinear and nonstationary nature of EEG, the recently developed
empirical mode decomposition (EMD) is incorporated, allowing a
decomposition of EEG into its inherent spectral components, referred
to as intrinsic mode functions (IMFs). By calculating the Shannon
entropy of IMFs in a time-dependent manner and summing them over
adaptive multiple scales, it results in an adaptive subscale entropy
measure of EEG. Simulation and experimental results show that
the proposed entropy properly reveals the dynamical changes over
multiple scales.
Abstract: In this research, TRACE model of Chinshan BWR/4
nuclear power plant (NPP) has been developed for the simulation and
analysis of ultimate response guideline (URG).The main actions of
URG are the depressurization and low pressure water injection of
reactor and containment venting. This research focuses to verify the
URG efficiency under Fukushima-like conditions. TRACE analysis
results show that the URG can keep the PCT below the criteria
1088.7 K under Fukushima-like conditions. It indicated that Chinshan
NPP was safe.
Abstract: There are many perceived advantages of microwave
ablation have driven researchers to develop innovative antennas to
effectively treat deep-seated, non-resectable hepatic tumors. In this
paper a coaxial antenna with a miniaturized sleeve choke has been
discussed for microwave interstitial ablation therapy, in order to
reduce backward heating effects irrespective of the insertion depth
into the tissue. Two dimensional Finite Element Method (FEM) is
used to simulate and measure the results of miniaturized sleeve choke
antenna. This paper emphasizes the importance of factors that can
affect simulation accuracy, which include mesh resolution, surface
heating and reflection coefficient. Quarter wavelength choke
effectiveness has been discussed by comparing it with the unchoked
antenna with same dimensions.
Abstract: This paper investigates simple implicit force control
algorithms realizable with industrial robots. A lot of approaches
already published are difficult to implement in commercial robot
controllers, because the access to the robot joint torques is necessary
or the complete dynamic model of the manipulator is used. In
the past we already deal with explicit force control of a position
controlled robot. Well known schemes of implicit force control are
stiffness control, damping control and impedance control. Using such
algorithms the contact force cannot be set directly. It is further
the result of controller impedance, environment impedance and
the commanded robot motion/position. The relationships of these
properties are worked out in this paper in detail for the chosen
implicit approaches. They have been adapted to be implementable
on a position controlled robot. The behaviors of stiffness control
and damping control are verified by practical experiments. For this
purpose a suitable test bed was configured. Using the full mechanical
impedance within the controller structure will not be practical in the
case when the robot is in physical contact with the environment. This
fact will be verified by simulation.
Abstract: Heat transfer due to forced convection of copper water
based nanofluid has been predicted by Artificial Neural network
(ANN). The present nanofluid is formed by mixing copper
nanoparticles in water and the volume fractions are considered here
are 0% to 15% and the Reynolds number are kept constant at 100.
The back propagation algorithm is used to train the network. The
present ANN is trained by the input and output data which has been
obtained from the numerical simulation, performed in finite volume
based Computational Fluid Dynamics (CFD) commercial software
Ansys Fluent. The numerical simulation based results are compared
with the back propagation based ANN results. It is found that the
forced convection heat transfer of water based nanofluid can be
predicted correctly by ANN. It is also observed that the back
propagation ANN can predict the heat transfer characteristics of
nanofluid very quickly compared to standard CFD method.
Abstract: Transportation of long turbine blades from one place
to another is a difficult process. Hence a feasibility study of
modularization of wind turbine blade was taken from structural
standpoint through finite element analysis. Initially, a non-segmented
blade is modeled and its structural behavior is evaluated to serve as
reference. The resonant, static bending and fatigue tests are simulated
in accordance with IEC61400-23 standard for comparison purpose.
The non-segmented test blade is separated at suitable location based
on trade off studies and the segments are joined with an innovative
double strap bonded joint configuration. The adhesive joint is
modeled by adopting cohesive zone modeling approach in ANSYS.
The developed blade model is analyzed for its structural response
through simulation. Performances of both the blades are found to be
similar, which indicates that, efficient segmentation of the long blade
is possible which facilitates easy transportation of the blades and on
site reassembling. The location selected for segmentation and
adopted joint configuration has resulted in an efficient segmented
blade model which proves the methodology adopted for segmentation
was quite effective. The developed segmented blade appears to be the
viable alternative considering its structural response specifically in
fatigue within considered assumptions.
Abstract: Non-crimp 3D orthogonal fabric composite is one of
the textile-based composite materials that are rapidly developing
light-weight engineering materials. The present paper focuses on
geometric and micromechanical modeling of non-crimp 3D
orthogonal carbon fabric and composites reinforced with it for
aerospace applications. In this research meso-finite element (FE)
modeling employs for stress analysis in different load conditions.
Since mechanical testing of expensive textile carbon composites with
specific application isn't affordable, simulation composite in a virtual
environment is a helpful way to investigate its mechanical properties
in different conditions.
Abstract: Plasmin plays an important role in the human
circulatory system owing to its catalytic ability of fibrinolysis. The
immediate injection of plasmin in patients of strokes has intrigued
many scientists to design vectors that can transport plasmin to the
desired location in human body. Here we predict the structure of
human plasmin and investigate the interaction of plasmin with the
gold-nanoparticle.
Because the crystal structure of plasminogen has been solved, we
deleted N-terminal domain (Pan-apple domain) of plasminogen and
generate a mimic of the active form of this enzyme (plasmin). We
conducted a simulated annealing process on plasmin and discovered a
very large conformation occurs. Kringle domains 1, 4 and 5 had been
observed to leave its original location relative to the main body of the
enzyme and the original doughnut shape of this enzyme has been
transformed to a V-shaped by opening its two arms. This observation
of conformational change is consistent with the experimental results of
neutron scattering and centrifugation.
We subsequently docked the plasmin on the simulated gold surface
to predict their interaction. The V-shaped plasmin could utilize its
Kringle domain and catalytic domain to contact the gold surface.
Our findings not only reveal the flexibility of plasmin structure but
also provide a guide for the design of a plasmin-gold nanoparticle.
Abstract: This research paper presents highly optimized barrel
shifter at 22nm Hi K metal gate strained Si technology node. This
barrel shifter is having a unique combination of static and dynamic
body bias which gives lowest power delay product. This power delay
product is compared with the same circuit at same technology node
with static forward biasing at ‘supply/2’ and also with normal reverse
substrate biasing and still found to be the lowest. The power delay
product of this barrel sifter is .39362X10-17J and is lowered by
approximately 78% to reference proposed barrel shifter at 32nm bulk
CMOS technology. Power delay product of barrel shifter at 22nm Hi
K Metal gate technology with normal reverse substrate bias is
2.97186933X10-17J and can be compared with this design’s PDP of
.39362X10-17J. This design uses both static and dynamic substrate
biasing and also has approximately 96% lower power delay product
compared to only forward body biased at half of supply voltage. The
NMOS model used are predictive technology models of Arizona state
university and the simulations to be carried out using HSPICE
simulator.
Abstract: To understand the friction stir welding process, it is
very important to know the nature of the material flow in and around
the tool. The process is a combination of both thermal as well as
mechanical work i.e. it is a coupled thermo-mechanical process.
Numerical simulations are very much essential in order to obtain a
complete knowledge of the process as well as the physics underlying
it. In the present work a model based approach is adopted in order to
study material flow. A thermo-mechanical based CFD model is
developed using a Finite Element package, Comsol Multiphysics.
The fluid flow analysis is done. The model simultaneously predicts
shear strain fields, shear strain rates and shear stress over the entire
workpiece for the given conditions. The flow fields generated by the
streamline plot give an idea of the material flow. The variation of
dynamic viscosity, velocity field and shear strain fields with various
welding parameters is studied. Finally the result obtained from the
above mentioned conditions is discussed elaborately and concluded.
Abstract: Waste load allocation (WLA) policies may use multiobjective
optimization methods to find the most appropriate and
sustainable solutions. These usually intend to simultaneously
minimize two criteria, total abatement costs (TC) and environmental
violations (EV). If other criteria, such as inequity, need for
minimization as well, it requires introducing more binary
optimizations through different scenarios. In order to reduce the
calculation steps, this study presents value index as an innovative
decision making approach. Since the value index contains both the
environmental violation and treatment costs, it can be maximized
simultaneously with the equity index. It implies that the definition of
different scenarios for environmental violations is no longer required.
Furthermore, the solution is not necessarily the point with minimized
total costs or environmental violations. This idea is testified for Haraz
River, in north of Iran. Here, the dissolved oxygen (DO) level of river
is simulated by Streeter-Phelps equation in MATLAB software. The
WLA is determined for fish farms using multi-objective particle
swarm optimization (MOPSO) in two scenarios. At first, the trade-off
curves of TC-EV and TC-Inequity are plotted separately as the
conventional approach. In the second, the Value-Equity curve is
derived. The comparative results show that the solutions are in a
similar range of inequity with lower total costs. This is due to the
freedom of environmental violation attained in value index. As a
result, the conventional approach can well be replaced by the value
index particularly for problems optimizing these objectives. This
reduces the process to achieve the best solutions and may find better
classification for scenario definition. It is also concluded that decision
makers are better to focus on value index and weighting its contents
to find the most sustainable alternatives based on their requirements.
Abstract: Channel sections are widely used in practice as beams.
However, design rules for eccentrically loaded (not through shear
center) beams with channel cross- sections are not available in
Eurocode 3. This paper compares the ultimate loads based on the
adjusted design rules for lateral torsional buckling of eccentrically
loaded channel beams in bending to the ultimate loads obtained with
Finite Element (FE) simulations on the basis of a parameter study.
Based on the proposed design rule, this study has led to a new design
rule which conforms to Eurocode 3.