Abstract: In this work, the Ictalurus punctatus species estimated
available physical habitat is compared with the estimated physical
habitat for the same but modified river reach, with the aim of creating
a linear park, along a length of 5 500 m.
To determine the effect of ecological park construction, on
physical habitat of the Lerma river stretch of study, first, the available
habitat for the Ictalurus punctatus species was estimated through the
simulation of the physical habitat, by using surveying, hydraulics,
and habitat information gotten at the river reach in its actual situation.
Second, it was estimated the available habitat for the above species,
upon the simulation of the physical habitat through the proposed
modification for the ecological park creation. Third, it is presented a
comparison between both scenarios in terms of available habitat
estimated for Ictalurus punctatus species, concluding that in cases of
adult and spawning life stages, changes in the channel to create an
ecological park would produce a considerable loss of potentially
usable habitat (PUH), while in the case of the juvenile life stage PUH
remains virtually unchanged, and in the case of life stage fry the PUH
would increase due to the presence of velocities and depths of lesser
magnitude, due to the presence of minor flow rates and lower volume
of the wet channel.
It is expected that habitat modification for linear park construction
may produce the lack of Ictalurus punktatus species conservation at
the river reach of the study.
Abstract: A sensory network consists of multiple detection
locations called sensor nodes, each of which is tiny, featherweight
and portable. A single path routing protocols in wireless sensor
network can lead to holes in the network, since only the nodes
present in the single path is used for the data transmission. Apart
from the advantages like reduced computation, complexity and
resource utilization, there are some drawbacks like throughput,
increased traffic load and delay in data delivery. Therefore, multipath
routing protocols are preferred for WSN. Distributing the traffic
among multiple paths increases the network lifetime. We propose a
scheme, for the data to be transmitted through a dominant path to
save energy. In order to obtain a high delivery ratio, a basic route
reconstruction protocol is utilized to reconstruct the path whenever a
failure is detected. A basic reconstruction routing (BRR) algorithm is
proposed, in which a node can leap over path failure by using the
already existing routing information from its neighbourhood while
the composed data is transmitted from the source to the sink. In order
to save the energy and attain high data delivery ratio, data is
transmitted along a multiple path, which is achieved by BRR
algorithm whenever a failure is detected. Further, the analysis of
how the proposed protocol overcomes the drawback of the existing
protocols is presented. The performance of our protocol is compared
to AOMDV and energy efficient node-disjoint multipath routing
protocol (EENDMRP). The system is implemented using NS-2.34.
The simulation results show that the proposed protocol has high
delivery ratio with low energy consumption.
Abstract: Nowadays, the use of renewable energy sources has been increasingly great because of the cost increase and public demand for clean energy sources. One of the fastest growing sources is wind energy. In this paper, Wind Diesel Hybrid System (WDHS) comprising a Diesel Generator (DG), a Wind Turbine Generator (WTG), the Consumer Load, a Battery-based Energy Storage System (BESS), and a Dump Load (DL) is used. Voltage is controlled by Diesel Generator; the frequency is controlled by BESS and DL. The BESS elimination is an efficient way to reduce maintenance cost and increase the dynamic response. Simulation results with graphs for the frequency of Power System, active power, and the battery power are presented for load changes. The controlling parameters are optimized by using Imperialist Competitive Algorithm (ICA). The simulation results for the BESS/no BESS cases are compared. Results show that in no BESS case, the frequency control is more optimal than the BESS case by using ICA.
Abstract: The main function of Medium Access Control (MAC) is to share the channel efficiently between all nodes. In the real-time scenario, there will be certain amount of wastage in bandwidth due to back-off periods. More bandwidth will be wasted in idle state if the back-off period is very high and collision may occur if the back-off period is small. So, an optimization is needed for this problem. The main objective of the work is to reduce delay due to back-off period thereby reducing collision and increasing throughput. Here a method, called the virtual back-off algorithm (VBA) is used to optimize the back-off period and thereby it increases throughput and reduces collisions. The main idea is to optimize the number of transmission for every node. A counter is introduced at each node to implement this idea. Here counter value represents the sequence number. VBA is classified into two types VBA with counter sharing (VBA-CS) and VBA with no counter sharing (VBA-NCS). These two classifications of VBA are compared for various parameters. Simulation is done in NS-2 environment. The results obtained are found to be promising.
Abstract: Electrohydraulic servo system have been used in industry in a wide number of applications. Its dynamics are highly nonlinear and also have large extent of model uncertainties and external disturbances. In this paper, a robust back-stepping control (RBSC) scheme is proposed to overcome the problem of disturbances and system uncertainties effectively and to improve the tracking performance of EHS systems. In order to implement the proposed control scheme, the system uncertainties in EHS systems are considered as total leakage coefficient and effective oil volume. In addition, in order to obtain the virtual controls for stabilizing system, the update rule for the system uncertainty term is induced by the Lyapunov control function (LCF). To verify the performance and robustness of the proposed control system, computer simulation of the proposed control system using Matlab/Simulink Software is executed. From the computer simulation, it was found that the RBSC system produces the desired tracking performance and has robustness to the disturbances and system uncertainties of EHS systems.
Abstract: To solve these problems, we investigated the management system of heating enterprise, including strategic planning based on the balanced scorecard (BSC), quality management in accordance with the standards of the Quality Management System (QMS) ISO 9001 and analysis of the system based on expert judgment using fuzzy inference. To carry out our work we used the theory of fuzzy sets, the QMS in accordance with ISO 9001, BSC, method of construction of business processes according to the notation IDEF0, theory of modeling using Matlab software simulation tools and graphical programming LabVIEW. The results of the work are as follows: We determined possibilities of improving the management of heat-supply plant-based on QMS; after the justification and adaptation of software tool it has been used to automate a series of functions for the management and reduction of resources and for the maintenance of the system up to date; an application for the analysis of the QMS based on fuzzy inference has been created with novel organization of communication software with the application enabling the analysis of relevant data of enterprise management system.
Abstract: This study addresses a concept of the Sustainable Building Environmental Model (SBEM) developed to optimize energy consumption in air conditioning and ventilation (ACV) systems without any deterioration of indoor environmental quality (IEQ). The SBEM incorporates two main components: an adaptive comfort temperature control module (ACT) and a new carbon dioxide demand control module (nDCV). These two modules take an innovative approach to maintain satisfaction of the Indoor Environmental Quality (IEQ) with optimum energy consumption; they provide a rational basis of effective control. A total of 2133 sets of measurement data of indoor air temperature (Ta), relative humidity (Rh) and carbon dioxide concentration (CO2) were conducted in some Hong Kong offices to investigate the potential of integrating the SBEM. A simulation was used to evaluate the dynamic performance of the energy and air conditioning system with the integration of the SBEM in an air-conditioned building. It allows us make a clear picture of the control strategies and performed any pre-tuned of controllers before utilized in real systems. With the integration of SBEM, it was able to save up to 12.3% in simulation of overall electricity consumption, and maintain the average carbon dioxide concentration within 1000ppm and occupant dissatisfaction in 20%.
Abstract: Encapsulated O-rings are specifically designed to address the problem of sealing the most hostile chemicals and extreme temperature applications. Ultrasonic vibration hot embossing and ultrasonic welding techniques provide a fast and reliable method to fabricate encapsulated O-ring. This paper performs the design and analysis method of the acoustic horns with double extrusion to process tube double side flange simultaneously. The paper deals with study through Finite Element Method (FEM) of ultrasonic stepped horn used to process a capsulated O-ring, the theoretical dimensions of horns, and their natural frequencies and amplitudes are obtained through the simulations of COMOSOL software. Furthermore, real horns were fabricated, tested and verified to proof the practical utility of these horns.
Abstract: This paper reports the development and application of a 2D1 depth-averaged model. The main goal of this contribution is to apply the depth averaged equations to a wind park model in which the treatment of the geometry, introduced on the mathematical model by the mass and momentum source terms. The depth-averaged model will be used in future to find the optimal position of wind turbines in the wind park. κ − ε and 2D LES turbulence models were consider in this article. 2D CFD2 simulations for one hill was done to check the depth-averaged model in practise.
Abstract: To explore how the brain may recognise objects in its
general,accurate and energy-efficient manner, this paper proposes the
use of a neuromorphic hardware system formed from a Dynamic
Video Sensor (DVS) silicon retina in concert with the SpiNNaker
real-time Spiking Neural Network (SNN) simulator. As a first step
in the exploration on this platform a recognition system for dynamic
hand postures is developed, enabling the study of the methods used
in the visual pathways of the brain. Inspired by the behaviours of
the primary visual cortex, Convolutional Neural Networks (CNNs)
are modelled using both linear perceptrons and spiking Leaky
Integrate-and-Fire (LIF) neurons.
In this study’s largest configuration using these approaches, a
network of 74,210 neurons and 15,216,512 synapses is created and
operated in real-time using 290 SpiNNaker processor cores in parallel
and with 93.0% accuracy. A smaller network using only 1/10th of the
resources is also created, again operating in real-time, and it is able
to recognise the postures with an accuracy of around 86.4% - only
6.6% lower than the much larger system. The recognition rate of the
smaller network developed on this neuromorphic system is sufficient
for a successful hand posture recognition system, and demonstrates
a much improved cost to performance trade-off in its approach.
Abstract: Hybrid electric vehicles can reduce pollution and
improve fuel economy. Power-split hybrid electric vehicles (HEVs)
provide two power paths between the internal combustion engine
(ICE) and energy storage system (ESS) through the gears of an
electrically variable transmission (EVT). EVT allows ICE to operate
independently from vehicle speed all the time. Therefore, the ICE can
operate in the efficient region of its characteristic brake specific fuel
consumption (BSFC) map. The two-mode powertrain can operate in
input-split or compound-split EVT modes and in four different fixed
gear configurations. Power-split architecture is advantageous because
it combines conventional series and parallel power paths. This
research focuses on input-split and compound-split modes in the
two-mode power-split powertrain. Fuzzy Logic Control (FLC) for an
internal combustion engine (ICE) and PI control for electric machines
(EMs) are derived for the urban driving cycle simulation. These
control algorithms reduce vehicle fuel consumption and improve ICE
efficiency while maintaining the state of charge (SOC) of the energy
storage system in an efficient range.
Abstract: Distributed applications deployed on LEO satellites
and ground stations require substantial communication between
different members in a constellation to overcome the earth
coverage barriers imposed by GEOs. Applications running on LEO
constellations suffer the earth line-of-sight blockage effect. They
need adequate lab testing before launching to space. We propose
a scalable cloud-based network simulation framework to simulate
problems created by the earth line-of-sight blockage. The framework
utilized cloud IaaS virtual machines to simulate LEO satellites
and ground stations distributed software. A factorial ANOVA
statistical analysis is conducted to measure simulator overhead on
overall communication performance. The results showed a very low
simulator communication overhead. Consequently, the simulation
framework is proposed as a candidate for testing LEO constellations
with distributed software in the lab before space launch.
Abstract: The paper develops a Non-Linear Model Predictive
Control (NMPC) of water quality in Drinking Water Distribution
Systems (DWDS) based on the advanced non-linear quality dynamics
model including disinfections by-products (DBPs). A special attention
is paid to the analysis of an impact of the flow trajectories prescribed
by an upper control level of the recently developed two-time scale
architecture of an integrated quality and quantity control in DWDS.
The new quality controller is to operate within this architecture in the
fast time scale as the lower level quality controller. The controller
performance is validated by a comprehensive simulation study based
on an example case study DWDS.
Abstract: Biomass briquette gasification is regarded as a
promising route for efficient briquette use in energy generation, fuels
and other useful chemicals. However, previous research has been
focused on briquette gasification in fixed bed gasifiers such as
updraft and downdraft gasifiers. Fluidised bed gasifier has the
potential to be effectively sized to medium or large scale. This study
investigated the use of fuel briquettes produced from blends of rice
husks and corn cobs biomass, in a bubbling fluidised bed gasifier.
The study adopted a combination of numerical equations and Aspen
Plus simulation software, to predict the product gas (syngas)
composition base on briquette density and biomass composition
(blend ratio of rice husks to corn cobs). The Aspen Plus model was
based on an experimentally validated model from the literature. The
results based on a briquette size 32 mm diameter and relaxed density
range of 500 to 650kg/m3, indicated that fluidisation air required in
the gasifier increased with increase in briquette density, and the
fluidisation air showed to be the controlling factor compared with the
actual air required for gasification of the biomass briquettes. The
mass flowrate of CO2 in the predicted syngas composition increased
with an increase in air flow, in the gasifier, while CO decreased and
H2 was almost constant. The ratio of H2 to CO for various blends of
rice husks and corn cobs did not significantly change at the designed
process air, but a significant difference of 1.0 was observed between
10/90 and 90/10 % blend of rice husks and corn cobs.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: In this study, the pedestrian simulation VISWALK
integration and application platform ant algorithms written program
made to construct a renovation engineering schedule planning mode.
The use of simulation analysis platform construction site when the user
running the simulation, after calculating the user walks in the case of
construction delays, the ant algorithm to find out the minimum delay
time schedule plan, and add volume and unit area deactivated loss of
business computing, and finally to the owners and users of two
different positions cut considerations pick out the best schedule
planning. To assess and validate its effectiveness, this study
constructed the model imported floor of a shopping mall floor
renovation engineering cases. Verify that the case can be found from
the mode of the proposed project schedule planning program can
effectively reduce the delay time and the user's walking mall loss of
business, the impact of the operation on the renovation engineering
facilities in the building to a minimum.
Abstract: Nowadays, the rapid development of CAD systems’
programming environments results in the creation of multiple
downstream applications, which are developed and becoming
increasingly available. CAD based manufacturing simulations is
gradually following the same trend. Drilling is the most popular holemaking
process used in a variety of industries. A specially built piece
of software that deals with the drilling kinematics is presented. The
cutting forces are calculated based on the tool geometry, the cutting
conditions and the tool/work-piece materials. The results are verified
by experimental work. Finally, the response surface methodology
(RSM) is applied and mathematical models of the total thrust force
and the thrust force developed because of the main cutting edges are
proposed.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: A compound parabolic concentrator (CPC) is a wellknown
non-imaging concentrator that will concentrate the solar
radiation onto receiver (PV cell). One of disadvantage of CPC is has
tall and narrow height compared to its diameter entry aperture area.
Therefore, for economic reason, a truncation had been done by
removed from the top of the full height CPC. This also will lead to
the decreases of concentration ratio but it will be negligible. In this
paper, the flux distribution of untruncated and truncated 2-D hollow
compound parabolic trough concentrator (hCPTC) design is
presented. The untruncated design has initial height H=193.4mm
with concentration ratio C_(2-D)=4. This paper presents the optical
simulation of compound parabolic trough concentrator using raytracing
software TracePro. Results showed that, after the truncation,
the height of CPC reduced 45% from initial height with the
geometrical concentration ratio only decrease 10%. Thus, the cost of
reflector and material dielectric usage can be saved especially at
manufacturing site.
Abstract: This article proposes a new method for application in
communication circuit systems that increase efficiency, PAE, output
power and gain in the circuit. The proposed method is based on a
combination of switching class-E and class-J and has been termed
class-EJ. This method was investigated using both theory and
simulation to confirm ∼72% PAE and output power of >39dBm. The
combination and design of the proposed power amplifier accrues gain
of over 15dB in the 2.9 to 3.5GHz frequency bandwidth. This circuit
was designed using MOSFET and high power transistors. The loadand
source-pull method achieved the best input and output networks
using lumped elements. The proposed technique was investigated for
fundamental and second harmonics having desirable amplitudes for
the output signal.