Abstract: In this study, mechanically alloyed Al 2024 powder is
densified by conventional sintering and by equal channel angular
pressing (ECAP) with and without back pressure. The powder was
encapsulated in an aluminium can for consolidation through ECAP.
The properties obtained in the compacts by conventional sintering
route and by ECAP are compared. The effect of conventional
sintering and ECAP on consolidation behaviour of powder,
microstructure, density and hardness is discussed. Room temperature
back pressure aided ECAP results in nearly full denser (97% of its
theoretical density) compact at room temperature. NanoIndentation
technique was used to determine the modulus of the consolidated
compacts.
Abstract: The effect of Alumina nanoparticle size on thermophysical
properties, heat transfer performance and pressure loss characteristics of
Aviation Turbine Fuel (ATF)-Al2O3 nanofluids is studied experimentally for
the proposed application of regenerative cooling of semi-cryogenic rocket
engine thrust chambers. Al2O3 particles with mean diameters of 50 nm or 150
nm are dispersed in ATF. At 500C and 0.3% particle volume concentration,
the bigger particles show increases of 17% in thermal conductivity and 55% in
viscosity, whereas the smaller particles show corresponding increases of 21%
and 22% for thermal conductivity and viscosity respectively. Contrary to these
results, experiments to study the heat transfer performance and pressure loss
characteristics show that at the same pumping power, the maximum
enhancement in heat transfer coefficient at 500C and 0.3% concentration is
approximately 47% using bigger particles, whereas it is only 36% using
smaller particles.
Abstract: If science is supposed to gain greater social
relevance and acceptance, researchers must not only relate to
the broader public, but also promote intercourse within the
ivory tower itself. The latter process has been under way
successfully for a number of years in the form of
transdisciplinary research initiatives. What is still lacking is a
broad debate about the necessity to look around properly and
face up to opposing views on one and the same topic within
our own discipline.
Abstract: Two indica varieties, IR36 and ‘Suweon 258’ (“S”)
are middle-heading in southern Japan. 36U, also middle-heading, is
an isogenic line of IR36 carrying Ur1 (Undulate rachis-1) gene.
However, late-heading plants segregated in the F2 population from
the F1 of S × 36U, and so did in the following generations. The
concerning lateness gene is designated as Ex. From the F8 generation,
isogenic-line pair of early-heading and late-heading lines, denoted by
“E” (ex/ex) and “L” (Ex/Ex), were developed. Genetic analyses of
heading time were conducted, using F1s and F2s among L, E, S and
36U. The following inferences were drawn from the experimental
results: 1) L, and both of E and 36U harbor Ex and ex, respectively;
2) Besides Ex, S harbors an inhibitor gene to it, i.e. I-Ex which is a
novel finding of the present study. 3) Ex is a dominant allele at the
E1 locus.
Abstract: The notions of intuitionistic fuzzy h-ideal and normal
intuitionistic fuzzy h-ideal in Γ-hemiring are introduced and some
of the basic properties of these ideals are investigated. Cartesian
product of intuitionistic fuzzy h-ideals is also defined. Finally a
characterization of intuitionistic fuzzy h-ideals in terms of fuzzy
relations is obtained.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: In recent years, a new numerical method has been
developed, the extended finite element method (X-FEM). The
objective of this work is to exploit the (X-FEM) for the treatment of
the fracture mechanics problems on 3D geometries, where we
showed the ability of this method to simulate the fatigue crack
growth into two cases: edge and central crack. In the results we
compared the six first natural frequencies of mode shapes uncracking
with the cracking initiation in the structure, and showed the stress
intensity factor (SIF) evolution function as crack size propagation
into structure, the analytical validation of (SIF) is presented. For to
evidence the aspects of this method, all result is compared between
FEA and X-FEM.
Abstract: This method decrease usage power (expenditure) in networks on chips (NOC). This method data coding for data transferring in order to reduces expenditure. This method uses data compression reduces the size. Expenditure calculation in NOC occurs inside of NOC based on grown models and transitive activities in entry ports. The goal of simulating is to weigh expenditure for encoding, decoding and compressing in Baseline networks and reduction of switches in this type of networks. KeywordsNetworks on chip, Compression, Encoding, Baseline networks, Banyan networks.
Abstract: Knowledge sharing enables the information or
knowledge to be transmitted from one source to another. This paper
demonstrates the needs of having the online book catalogue which
can be used to facilitate disseminating information on textbook used
in the university. This project is aimed to give access to the students
and lecturers to the list of books in the bookstore and at the same
time to allow book reviewing without having to visit the bookstore
physically. Research is carried out according to the boundaries which
accounts to current process of new book purchasing, current system
used by the bookstore and current process the lecturers go through
for reviewing textbooks. The questionnaire is used to gather the
requirements and it is distributed to 100 students and 40 lecturers.
This project has enabled the improvement of a manual process to be
carried out automatically, through a web based platform. It is shown
based on the user acceptance survey carried out that target groups
found that this web service is feasible to be implemented in
Universiti Teknologi PETRONAS (UTP), and they have shown
positive signs of interest in utilizing it in the future.
Abstract: In this paper, we propose a texture feature-based
language identification using wavelet-domain BDIP (block difference
of inverse probabilities) and BVLC (block variance of local
correlation coefficients) features and FFT (fast Fourier transform)
feature. In the proposed method, wavelet subbands are first obtained
by wavelet transform from a test image and denoised by Donoho-s
soft-thresholding. BDIP and BVLC operators are next applied to the
wavelet subbands. FFT blocks are also obtained by 2D (twodimensional)
FFT from the blocks into which the test image is
partitioned. Some significant FFT coefficients in each block are
selected and magnitude operator is applied to them. Moments for each
subband of BDIP and BVLC and for each magnitude of significant
FFT coefficients are then computed and fused into a feature vector. In
classification, a stabilized Bayesian classifier, which adopts variance
thresholding, searches the training feature vector most similar to the
test feature vector. Experimental results show that the proposed
method with the three operations yields excellent language
identification even with rather low feature dimension.
Abstract: This paper is concerned with the design and implementation of MICOSim, an event-driven simulator written in Java for evaluating the performance of Grid entities (users, brokers and resources) under different scenarios such as varying the numbers of users, resources and brokers and varying their specifications and employed strategies.
Abstract: This article discusses the questions concerning of creating small packet networks for energy companies with application of high voltage power line carrier equipment (PLC) with functionality of IP traffic transmission. The main idea is to create converged PLC links between substations and dispatching centers where packet data and voice are transmitted in one data flow. The article contents description of basic conception of the network, evaluation of voice traffic transmission parameters, and discussion of header compression techniques in relation to PLC links. The results of exploration show us, that convergent packet PLC links can be very useful in the construction of small packet networks between substations in remote locations, such as deposits or low populated areas.
Abstract: This research were investigated, determined, and
analyzed of the climate characteristically change in the provincial
Udon Thani in the period of 60 surrounding years from 1951 to 2010
A.D. that it-s transferred to effects of climatologically data for
determining global warming. Statistically significant were not found
for the 60 years- data (R2
Abstract: The majority of existing predictors for time series are
model-dependent and therefore require some prior knowledge for the
identification of complex systems, usually involving system
identification, extensive training, or online adaptation in the case of
time-varying systems. Additionally, since a time series is usually
generated by complex processes such as the stock market or other
chaotic systems, identification, modeling or the online updating of
parameters can be problematic. In this paper a model-free predictor
(MFP) for a time series produced by an unknown nonlinear system or
process is derived using tracking theory. An identical derivation of the
MFP using the property of the Newton form of the interpolating
polynomial is also presented. The MFP is able to accurately predict
future values of a time series, is stable, has few tuning parameters and
is desirable for engineering applications due to its simplicity, fast
prediction speed and extremely low computational load. The
performance of the proposed MFP is demonstrated using the
prediction of the Dow Jones Industrial Average stock index.
Abstract: Nanomaterials have attracted considerable attention
during the last two decades, due to their unusual electrical, mechanical
and other physical properties as compared with their bulky
counterparts. The mechanical properties of nanostructured materials
show strong size dependency, which has been explained within the
framework of continuum mechanics by including the effects of surface
stress. The size-dependent deformations of two-dimensional
nanosized structures with surface effects are investigated in the paper
by the finite element method. Truss element is used to evaluate the
contribution of surface stress to the total potential energy and the
Gurtin and Murdoch surface stress model is implemented with
ANSYS through its user programmable features. The proposed
approach is used to investigate size-dependent stress concentration
around a nanosized circular hole and the size-dependent effective
moduli of nanoporous materials. Numerical results are compared with
available analytical results to validate the proposed modeling
approach.
Abstract: Software crisis refers to the situation in which the developers are not able to complete the projects within time and budget constraints and moreover these overscheduled and over budget projects are of low quality as well. Several methodologies have been adopted form time to time to overcome this situation and now in the focus is component based software engineering. In this approach, emphasis is on reuse of already existing software artifacts. But the results can not be achieved just by preaching the principles; they need to be practiced as well. This paper highlights some of the very basic elements of this approach, which has to be in place to get the desired goals of high quality, low cost with shorter time-to-market software products.
Abstract: The purpose of this investigation is to relate the rain
power and the overland flow power to soil erodibility to assess the
effects of both parameters on soil erosion using variable rainfall
intensity on remoulded agricultural soil. Six rainfall intensities were
used to simulate the natural rainfall and are as follows: 12.4mm/h,
20.3mm/h, 28.6mm/h, 52mm/h, 73.5mm/h and 103mm/h. The results
have shown that the relationship between overland flow power and
rain power is best represented by a linear function (R2=0.99). As
regards the relationships between soil erodibility factor and rain and
overland flow powers, the evolution of both parameters with the
erodibility factor follow a polynomial function with high coefficient
of determination. From their coefficients of determination (R2=0.95)
for rain power and (R2=0.96) for overland flow power, we can
conclude that the flow has more power to detach particles than rain.
This could be explained by the fact that the presence of particles,
already detached by rain and transported by the flow, give the flow
more weight and then contribute to the detachment of particles by
collision.
Abstract: The main goal of this work is to propose a way for
combined use of two nontraditional algorithms by solving topological
problems on telecommunications concentrator networks. The
algorithms suggested are the Simulated Annealing algorithm and the
Genetic Algorithm. The Algorithm of Simulated Annealing unifies
the well known local search algorithms. In addition - Simulated
Annealing allows acceptation of moves in the search space witch lead
to decisions with higher cost in order to attempt to overcome any
local minima obtained. The Genetic Algorithm is a heuristic approach
witch is being used in wide areas of optimization works. In the last
years this approach is also widely implemented in
Telecommunications Networks Planning. In order to solve less or
more complex planning problem it is important to find the most
appropriate parameters for initializing the function of the algorithm.
Abstract: Nowadays, the rapid development of multimedia
and internet allows for wide distribution of digital media data.
It becomes much easier to edit, modify and duplicate digital
information Besides that, digital documents are also easy to
copy and distribute, therefore it will be faced by many
threatens. It-s a big security and privacy issue with the large
flood of information and the development of the digital
format, it become necessary to find appropriate protection
because of the significance, accuracy and sensitivity of the
information. Nowadays protection system classified with more
specific as hiding information, encryption information, and
combination between hiding and encryption to increase information
security, the strength of the information hiding science is due to the
non-existence of standard algorithms to be used in hiding secret
messages. Also there is randomness in hiding methods such as
combining several media (covers) with different methods to pass a
secret message. In addition, there are no formal methods to be
followed to discover the hidden data. For this reason, the task of this
research becomes difficult. In this paper, a new system of information
hiding is presented. The proposed system aim to hidden information
(data file) in any execution file (EXE) and to detect the hidden file
and we will see implementation of steganography system which
embeds information in an execution file. (EXE) files have been
investigated. The system tries to find a solution to the size of the
cover file and making it undetectable by anti-virus software. The
system includes two main functions; first is the hiding of the
information in a Portable Executable File (EXE), through the
execution of four process (specify the cover file, specify the
information file, encryption of the information, and hiding the
information) and the second function is the extraction of the hiding
information through three process (specify the steno file, extract the
information, and decryption of the information). The system has
achieved the main goals, such as make the relation of the size of the
cover file and the size of information independent and the result file
does not make any conflict with anti-virus software.
Abstract: Paper presents knowledge about types of test in area
of materials properties of selected methods of rapid prototyping
technologies. In today used rapid prototyping technologies for
production of models and final parts are used materials in initial state
as solid, liquid or powder material structure. In solid state are used
various forms such as pellets, wire or laminates. Basic range
materials include paper, nylon, wax, resins, metals and ceramics. In
Fused Deposition Modeling (FDM) rapid prototyping technology are
mainly used as basic materials ABS (Acrylonitrile Butadiene
Styrene), polyamide, polycarbonate, polyethylene and polypropylene.
For advanced FDM applications are used special materials as silicon
nitrate, PZT (Piezoceramic Material - Lead Zirconate Titanate),
aluminium oxide, hydroxypatite and stainless steel.