Abstract: The paper deals with current issues in research of
advanced methods to increase reliability of traditional timber
structural elements. It analyses the issue of strengthening of bent
timber beams, such as ceiling beams in old (historical) buildings with
additional concrete slab in combination with externally bonded fibre -
reinforced polymer. The paper describes experimental testing of
composite timber-concrete beam with FRP reinforcement and
compares results with FEM analysis.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive (UI) single phase inverter (SPI) for a
photovoltaic (PV) system at residential/distribution level. The
proposed model uses single-phase phase locked loop (PLL) to
synchronize SPI with the grid and performs MPC control in a dq
reference frame. SPI model consists of boost converter (BC),
maximum power point tracking (MPPT) control, and a full bridge
(FB) voltage source inverter (VSI). No PI regulators to tune and
carrier and modulating waves are required to produce switching
sequence. Instead, the operational model of VSI is used to synthesize
sinusoidal current and track the reference. Model is validated using a
three kW PV system at the input of UI-SPI in Matlab/Simulink.
Implementation and results demonstrate simplicity and accuracy, as
well as reliability of the model.
Abstract: This paper presents a hybrid three phase rectifier for
high power factor application. This rectifier is composed by zero
voltage transition (ZVT) and zero current transition (ZCT) boost
converter with three phase diode bridge rectifier, in parallel with a six
pulse three phase pulse width modulation (PWM) controlled rectifier.
The proposed topology is capable of high power factor with DC
output voltage regulation by providing sinusoidal input. Also, it
increases the overall efficiency of the new hybrid rectifier to 94.56%
and the total harmonic distortion of the hybrid structure varies from
0% to 16% at nominal output power. This topology was simulated in
MATLAB/SIMULINK environment and the output waveforms
presented with experimental result.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: The article presents the concept of an electromagnetic
circuit generator with permanent magnets mounted on the surface
rotor core designed for single phase work. Computation field-circuit
model was shown. The spectrum of time course of voltages in the
idle work was presented. The cross section with graphically
presentation of magnetic induction in particular parts of
electromagnetic circuits was presented. Distribution of magnetic
induction at the rated load point for each phase was shown. The time
course of voltages and currents for each phases for rated power were
displayed. An analysis of laboratory results and measurement of load
characteristics of the generator was discussed. The work deals with
three electromagnetic circuits of generators with permanent magnet
where output voltage characteristics versus rated power were
expressed.
Abstract: The purpose of this research was to identify factors
that influenced the success of e-commerce implementation within
SMEs businesses. In order to achieve the objectives of this research,
the researcher collected data from random firms in Thailand, both the
users and those who are not using the e-commerce. The data was
comprised of the results of 310 questionnaires, as well as 10
interviews with owner/managers of businesses who are currently
using e-commerce successfully. The data were analyzed by using
descriptive statistics, which included frequency, percentages, mean,
and the standard deviation of pertinent factors. Independent t-test and
one-way ANOVA test were also used. The findings of this research
revealed that 50% of all the firms surveyed had e-commerce website,
whereas, over 20% of all firms surveyed had developing an ecommerce
strategy. The result findings also indicate that
organizational factors, technological factors and environment factors
as significant factors effecting success of e-commerce
implementation in SMEs. From the hypotheses testing, the findings
revealed that the different level of support use ecommerce by
owner/manager had different success in e-commerce implementation.
Moreover, the difference in e-commerce management approach
affected the success in terms of higher total sales for the business or
higher number of retained or returning customers.
Abstract: Access control is one of the most challenging issues
facing information security. Access control is defined as, the ability to
permit or deny access to a particular computational resource or digital
information by an unauthorized user or subject. The concept of usage
control (UCON) has been introduced as a unified approach to capture a
number of extensions for access control models and systems. In
UCON, an access decision is determined by three factors:
authorizations, obligations and conditions. Attribute mutability and
decision continuity are two distinct characteristics introduced by
UCON for the first time. An observation of UCON components
indicates that, the components are predefined and static. In this paper,
we propose a new and flexible model of usage control for the creation
and elimination of some of these components; for example new
objects, subjects, attributes and integrate these with the original
UCON model. We also propose a model for concurrent usage
scenarios in UCON.
Abstract: Malathion (ML) is a well known pesticide commonly
used in many agricultural and non-agricultural processes. Its toxicity
has been attributed primarily to the accumulation of acetylcholine
(Ach) at nerve junctions, due to the inhibition of acetylcholinesterase
(AChE). The aim of the current research was to study the protective
effect of the melissa plant extract against reproductive impairment
induced by malathion in 32 male albino rats, and the biological
experiment was divided into four groups (8 in each) that given
malathion (27 mg/kg; 1/50 of the LD50 for an oral dose) and/or
Melissa officinalis (MO) extract (200mg/kg/day) by gavages
technique. The sperm counts, sperm motility, sperm morphology,
FSH, LH, and testosterone levels had been determined in testes
homogenate at the end of the experiment. It is worthy to report that,
rats treated with melissa extract did not show a significant difference
when compared with the control group, while rats given malathion
alone had significantly lower sperm count, sperm motility, and
significantly higher abnormal sperm numbers, than the untreated
control rats as well as having significantly lower serum FSH, LH, and
testosterone levels compared with the control group. Administrations
of melissa extract restore all mentioned histological parameters
towards the control group and the melissa extract had a strong
positive protective effect against malathion toxicity. Results the of
biological parameters were confirmed by the histological
examination of rat testes and indicated that, both control and melissa
groups showing normal seminiferous tubules, while malathion group
testicular tissues had necrosis, edema in the seminiferous tubules and
degeneration of spermatogonial cells lining the seminiferous tubules
with incomplete spermatogenesis. The use of melissa against
malathion improved the histological picture and showing normal
seminiferous tubules with complete spermatogenesis and almost there
was no histopathological changes could be noted.
Abstract: Business interpreting talents are in badly need for local
economic development, but currently there are problems of traditional
business interpreting training mode in China. In view of the good
opportunity for college business interpreters provided by international
trading center development in Qingdao China and with the aim of
being in line with market demand and enhancing business interpreters'
employment competitive advantage, this paper aims to explore how to
cultivate interdisciplinary business interpreting talents based on
market demand.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: The paper a summary of the results of concretes with
partial substitution of natural aggregates with recycled concrete is
solved. Design formulas of the concretes were characterised with 20,
40 and 60% substitution of natural 8-16mm fraction aggregates with
a selected recycled concrete of analogous coarse fractions. With the
product samples an evaluation of coarse fraction aggregates influence
on fresh concrete consistency and concrete strength in time was
carried out. The results of concretes with aggregates substitution will
be compared to reference formula containing only the fractions of
natural aggregates.
Abstract: Anultra-low power capacitor less low-dropout voltage
regulator with improved transient response using gain enhanced feed
forward path compensation is presented in this paper. It is based on a
cascade of a voltage amplifier and a transconductor stage in the feed
forward path with regular error amplifier to form a composite gainenhanced
feed forward stage. It broadens the gain bandwidth and thus
improves the transient response without substantial increase in power
consumption. The proposed LDO, designed for a maximum output
current of 100 mA in UMC 180 nm, requires a quiescent current of
69 )A. An undershot of 153.79mV for a load current changes from
0mA to 100mA and an overshoot of 196.24mV for current change of
100mA to 0mA. The settling time is approximately 1.1 )s for the
output voltage undershooting case. The load regulation is of 2.77
)V/mA at load current of 100mA. Reference voltage is generated by
using an accurate band gap reference circuit of 0.8V.The costly
features of SOC such as total chip area and power consumption is
drastically reduced by the use of only a total compensation
capacitance of 6pF while consuming power consumption of 0.096
mW.
Abstract: Currently, biological control programs in greenhouse
crops involve the use, at the same time, several natural enemies
during the crop cycle. Also, large number of plant species grown in
greenhouses, among them, the used cultivars are also wide. However,
the cultivar effects on entomophagous species efficacy (predators and
parasitoids) have been scarcely studied. A new method had been
developed, using the factitious prey or host Ephestia kuehniella. It
allow us to evaluate, under greenhouse or controlled conditions
(semi-field), the cultivar effects on the entomophagous species
effectiveness. The work was carried out in greenhouse tomato crop. It
has been found the biological and ecological activities of predatory
species (Nesidiocoris tenuis) and egg-parasitoid (Trichogramma
achaeae) can be well represented with the use of the factitious prey
or host; being better in the former than the latter. The data found in
the trial are shown and discussed. The developed method could be
applied to evaluate new plant materials before making available to
farmers as commercial varieties, at low costs and easy use.
Abstract: In this paper we make a temperature investigations in
two type of superposed crimped connections using experimental
determinations. All the samples use 8 copper wire 7.1 x 3 mm2
crimped by two methods: the first method uses one crimp indents and
the second is a proposed method with two crimp indents. The ferrule
is a parallel one. We study the influence of number and position of
crimp indents. The samples are heated in A.C. current at different
current values until steady state heating regime. After obtaining of
temperature values, we compare them and present the conclusion.
Abstract: Two types of commercial cylindrical lithium ion
batteries (Panasonic 3.4 Ah NCR-18650B and Samsung 2.9 Ah
INR-18650), were investigated experimentally. The capacities of these
samples were individually measured using constant current-constant
voltage (CC-CV) method at different ambient temperatures (-10°C,
0°C, 25°C). Their internal resistance was determined by
electrochemical impedance spectroscopy (EIS) and pulse discharge
methods. The cells with different configurations of parallel connection
NCR-NCR, INR-INR and NCR-INR were charged/discharged at the
aforementioned ambient temperatures. The results showed that the
difference of internal resistance between cells much more evident at
low temperatures. Furthermore, the parallel connection of NCR-NCR
exhibits the most uniform temperature distribution in cells at -10°C,
this feature is quite favorable for the safety of the battery pack.
Abstract: Web search engines are designed to retrieve and
extract the information in the web databases and to return dynamic
web pages. The Semantic Web is an extension of the current web in
which it includes semantic content in web pages. The main goal of
semantic web is to promote the quality of the current web by
changing its contents into machine understandable form. Therefore,
the milestone of semantic web is to have semantic level information
in the web. Nowadays, people use different keyword- based search
engines to find the relevant information they need from the web.
But many of the words are polysemous. When these words are
used to query a search engine, it displays the Search Result Records
(SRRs) with different meanings. The SRRs with similar meanings are
grouped together based on Word Sense Disambiguation (WSD). In
addition to that semantic annotation is also performed to improve the
efficiency of search result records. Semantic Annotation is the
process of adding the semantic metadata to web resources. Thus the
grouped SRRs are annotated and generate a summary which
describes the information in SRRs. But the automatic semantic
annotation is a significant challenge in the semantic web. Here
ontology and knowledge based representation are used to annotate
the web pages.
Abstract: As currently various portable devices were launched,
smart business conducted using them became common. Since smart
business can use company-internal resources in an exlternal remote
place, user authentication that can identify authentic users is an
important factor. Commonly used user authentication is a method of
using user ID and Password. In the user authentication using ID and
Password, the user should see and enter authentication information
him or her. In this user authentication system depending on the user’s
vision, there is the threat of password leaks through snooping in the
process which the user enters his or her authentication information.
This study designed and produced a user authentication module
using an actuator to respond to the snooping threat.
Abstract: The purposes of this research were to study concepts
and strategies of human resource development in the automotive
manufacturers and to articulate the proposals against the government
about the human resource development for automotive industry. In
the present study, qualitative study was an in-depth interview in
which the qualitative data were collected from the executive or the
executive of human resource division from five automotive
companies - Toyota Motor (Thailand) Co., Ltd., Nissan Motor
(Thailand) Co., Ltd., Mitsubishi Motors (Thailand) Co., Ltd., Honda
Automobile (Thailand) Co., Ltd., and Suzuki Motor (Thailand) Co.,
Ltd. Qualitative data analysis was performed by using inter-coder
agreement technique. The research findings were as follows:
The external factors included the current conditions of the
automotive industry, government’s policy related to the automotive
industry, technology, labor market and human resource development
systems of the country. The internal factors included management,
productive management, organizational strategies, leadership,
organizational culture and philosophy of human resource
development. These factors were affected to the different concept of
human resources development -the traditional human resource
development and the strategies of human resource development. The
organization focuses on human resources as intellectual capital and
uses the strategies of human resource development in all
development processes. The strategies of human resource
development will enhance the ability of human resources in the
organization and the country.
Abstract: Concerns on corrosion and effective coating
protection of double hull tankers and bulk carriers in service have
been raised especially in water ballast tanks (WBTs). Test
protocols/methodologies specifically that which is incorporated in the
International Maritime Organisation (IMO), Performance Standard
for Protective Coatings for Dedicated Sea Water ballast tanks (PSPC)
are being used to assess and evaluate the performance of the coatings
for type approval prior to their application in WBTs. However, some
of the type approved coatings may be applied as very thick films to
less than ideally prepared steel substrates in the WBT. As such films
experience hygrothermal cycling from operating and environmental
conditions, they become embrittled which may ultimately result in
cracking. This embrittlement of the coatings is identified as an
undesirable feature in the PSPC but is not mentioned in the test
protocols within it. There is therefore renewed industrial research
aimed at understanding this issue in order to eliminate cracking and
achieve the intended coating lifespan of 15 years in good condition.
This paper will critically review test protocols currently used for
assessing and evaluating coating performance, particularly the IMO
PSPC.
Abstract: Lightning protection systems (LPS) for wind power
generation is becoming an important public issue. A serious damage
of blades, accidents where low-voltage and control circuit
breakdowns are frequently occur in many wind farms. A grounding
system is one of the most important components required for
appropriate LPSs in wind turbines WTs. Proper design of a wind
turbine grounding system is demanding and several factors for the
proper and effective implementation must taken into account. In this
paper proposed procedure of proper design of grounding systems for
a wind turbine was introduced. This procedure depends on measuring
of ground current of simulated wind farm under lightning taking into
consideration the soil ionization. The procedure also includes the
Ground Potential Rise (GPR) and the voltage distributions at ground
surface level and Touch potential. In particular, the contribution of
mitigating techniques, such as rings, rods and the proposed design
were investigated.