Abstract: In the gas refineries of Iran-s South Pars Gas
Complex, Sulfrex demercaptanization process is used to remove
volatile and corrosive mercaptans from liquefied petroleum gases by
caustic solution. This process consists of two steps. Removing low
molecular weight mercaptans and regeneration exhaust caustic. Some
parameters such as LPG feed temperature, caustic concentration and
feed-s mercaptan in extraction step and sodium mercaptide content in
caustic, catalyst concentration, caustic temperature, air injection rate
in regeneration step are effective factors. In this paper was focused on
temperature factor that play key role in mercaptans extraction and
caustic regeneration. The experimental results demonstrated by
optimization of temperature, sodium mercaptide content in caustic
because of good oxidation minimized and sulfur impurities in
product reduced.
Abstract: Through inward perceptions, we intuitively expect
distributed software development to increase the risks associated with
achieving cost, schedule, and quality goals. To compound this
problem, agile software development (ASD) insists one of the main
ingredients of its success is cohesive communication attributed to
collocation of the development team. The following study identified
the degree of communication richness needed to achieve comparable
software quality (reduce pre-release defects) between distributed and
collocated teams. This paper explores the relevancy of
communication richness in various development phases and its
impact on quality. Through examination of a large distributed agile
development project, this investigation seeks to understand the levels
of communication required within each ASD phase to produce
comparable quality results achieved by collocated teams. Obviously,
a multitude of factors affects the outcome of software projects.
However, within distributed agile software development teams, the
mode of communication is one of the critical components required to
achieve team cohesiveness and effectiveness. As such, this study
constructs a distributed agile communication model (DAC-M) for
potential application to similar distributed agile development efforts
using the measurement of the suitable level of communication. The
results of the study show that less rich communication methods, in
the appropriate phase, might be satisfactory to achieve equivalent
quality in distributed ASD efforts.
Abstract: Linearization of graph embedding has been emerged
as an effective dimensionality reduction technique in pattern
recognition. However, it may not be optimal for nonlinearly
distributed real world data, such as face, due to its linear nature. So, a
kernelization of graph embedding is proposed as a dimensionality
reduction technique in face recognition. In order to further boost the
recognition capability of the proposed technique, the Fisher-s
criterion is opted in the objective function for better data
discrimination. The proposed technique is able to characterize the
underlying intra-class structure as well as the inter-class separability.
Experimental results on FRGC database validate the effectiveness of
the proposed technique as a feature descriptor.
Abstract: An experiment was conducted in October 2008 due the ability replacement plant associate biofertilizers by chemical fertilizers and the qualifying rate of chemical N fertilizers at the moment of using this biofertilizers and the interaction of this biofertilizer on each other. This field experiment has been done in Persepolis (Throne of Jamshid) and arrange by using factorial with the basis of randomized complete block design, in three replication Azespirilium SP bacteria has been admixed with consistence 108 cfu/g and inoculated with seeds of wheat, The streptomyces SP has been used in amount of 550 gr/ha and concatenated on clay and for the qualifying range of chemical fertilizer 4 level of N chemical fertilizer from the source of urea (N0=0, N1=60, N2=120, N3=180) has been used in this experiment. The results indicated there were Significant differences between levels of Nitrogen fertilizer in the entire characteristic which has been measured in this experiment. The admixed Azespirilium SP showed significant differences between their levels in the characteristics such as No. of fertile ear, No. of grain per ear, grain yield, grain protein percentage, leaf area index and the agronomic fertilizer use efficiency. Due the interaction streptomyses with Azespirilium SP bacteria this actinomycet didn-t show any statistically significant differences between it levels.
Abstract: Dynamic shear test on simulated phantom can be used
to validate magnetic resonance elastography (MRE) measurements.
Phantom gel has been usually utilized for the cell culture of cartilage
and soft tissue and also been used for mechanical property
characterization using imaging systems. The viscoelastic property of
the phantom would be important for dynamic experiments and
analyses. In this study, An axisymmetric FE model is presented for
determining the dynamic shear behaviour of brain simulated phantom
using ABAQUS. The main objective of this study was to investigate
the effect of excitation frequencies and boundary conditions on shear
modulus and shear viscosity in viscoelastic media.
Abstract: Field Association (FA) terms are a limited set of discriminating terms that give us the knowledge to identify document fields which are effective in document classification, similar file retrieval and passage retrieval. But the problem lies in the lack of an effective method to extract automatically relevant Arabic FA Terms to build a comprehensive dictionary. Moreover, all previous studies are based on FA terms in English and Japanese, and the extension of FA terms to other language such Arabic could be definitely strengthen further researches. This paper presents a new method to extract, Arabic FA Terms from domain-specific corpora using part-of-speech (POS) pattern rules and corpora comparison. Experimental evaluation is carried out for 14 different fields using 251 MB of domain-specific corpora obtained from Arabic Wikipedia dumps and Alhyah news selected average of 2,825 FA Terms (single and compound) per field. From the experimental results, recall and precision are 84% and 79% respectively. Therefore, this method selects higher number of relevant Arabic FA Terms at high precision and recall.
Abstract: One of the most important aspects expected from an
ERP system is to mange user\administrator manual documents
dynamically. Since an ERP package is frequently changed during its
implementation in customer sites, it is often needed to add new
documents and/or apply required changes to existing documents in
order to cover new or changed capabilities. The worse is that since
these changes occur continuously, the corresponding documents
should be updated dynamically; otherwise, implementing the ERP
package in the organization encounters serious risks. In this paper, we
propose a new architecture which is based on the agent oriented
vision and supplies the dynamic document generation expected from
ERP systems using several independent but cooperative agents.
Beside the dynamic document generation which is the main issue of
this paper, the presented architecture will address some aspects of
intelligence and learning capabilities existing in ERP.
Abstract: The purpose of study was to design and construction
the semi-automatic sliced ginger machine for reduce production times
in sheet and slice ginger procedure furthermore, reduced amount of
labor of slides and cutting method. Take consider into clean and safety of workers and consumers. The principle of machines, used 1
horsepower motor, rotation speed of sliced blade 967 rpm, the diameter of sliced dish 310 mm, consists of 2 blades for sheet cutting
ginger and the power from motor which transfer to rotate the sliced blade roller, rotation speed 440 rpm. The slice cutter roller was sliced
ginger from sheet ginger to line ginger. The conveyer could
adjustment level of motors, used to the beginning area that sheet
ginger was transference to the roller for sheet and sliced cutting in next process. The cover of sliced cutting had channel for 1 tuber of
ginger. The semi-automatic sliced ginger machine could produced sheet ginger 81.8 kg/h (6.2 times of labor) and line ginger 17.9 kg/h
(2.5 times of labor) compare with, labor work could produced sheet
ginger 13.2 kg/h and line ginger 7.1 kg/h, and when timekeeper, the
total times of semi auto machine 30.86 kg/h and labor 4.6 kg/h, there
for the semi auto machine was 6.7 times of labor. The semiautomatic
sliced ginger machine convenient, easy for use and
maintain, in addition to reduce fatigue of body and seriousness from
works; must be used high skill, and protection accident in slicing
procedure. Beside, machine could used with other vegetables for
example potato, carrot .etc
Abstract: The cycles of the steam-injection gas-turbine systems are studied. The analyses of the parametric effects and the optimal operating conditions for the steam-injection gas-turbine (STIG) system and the regenerative steam-injection gas-turbine (RSTIG) system are investigated to ensure the maximum performance. Using the analytic model, the performance parameters of the system such as thermal efficiency, fuel consumption and specific power, and also the optimal operating conditions are evaluated in terms of pressure ratio, steam injection ratio, ambient temperature and turbine inlet temperature (TIT). It is shown that the computational results are presented to have a notable enhancement of thermal efficiency and specific power.
Abstract: The response of King Abdulla Canal (KAC) water to the upgrade of As Samra Wastewater Treatment Plant which discharges its effluent to the Zarqa River is investigated. Time series quality data that extends between October 2005 and December 2009 obtained by a state of the art telemetric monitoring system were analyzed for COD, EC, TP and TN at two monitoring stations located upstream and downstream of the confluence of the Zarqa River with KAC. The samples- means and the t-test showed that there has been significant improvement in the quality of the KAC water for COD, and TP. However, the improvement in the TN was found statistically insignificant, whereas the EC of the KAC was unaffected by the upgrade. Comparing the selected parameters with the standards and guidelines for using treated wastewater in irrigation showed that the KAC water has improved towards meeting the required standards and guidelines for treated wastewater reuse in irrigation.
Abstract: In the Northern hemisphere, sheep reproduction is
seasonal (September-November). Among several natural factors
influencing the reproduction status of rams, we studied the daylight
length and temperature. Rams from different breeds were studied:
Merinos de Palas (half-precocious), Karakul de Botosani (halfbelated)
and Turcana (belated breed, low reproductive plasticity). In
Merinos de Palas, ejaculate volume during sexual repose is 51.3%
from normal quantity. When autumn climate was experimentally
induced, ejaculate volume reached 98.45% (Merinos), 94.97%
(Karakul) and 97.59% (Turcana). Semen density increased from
1.031-1.033 till 1.035 after exposition to artificial light and
temperature conditions. Spermatozoids mobility and sperm pH
improved, passing over 82% and 6.75, values identical to those in the
natural reproduction season. Behaviour analysis after
photoperiodicity indicated that over 83.3% Merinos and Karakul
males and all Turcana rams exteriorised normal and intense sexual
reflexes. Certain effort and reduced expenses brought rams in good
condition, producing higher quantity and quality sperm.
Abstract: In the present paper the results of a numerical study are presented, numerical models were developed to simulate the behaviour of vertical massive dikes. The proposed models were developed according to the geometry, boundary conditions, loading conditions and initial conditions of a physical model taken as reference. The results obtained were compared to the experimental data. As far as the overall behaviour, the displacements and the failure mechanisms of the dikes is concerned, the numerical results were in good agreement with the experimental results, which clearly indicates a good quality of numerical modelling. The validated numerical models were used in a parametric study were the displacements and failure mechanisms were fully investigated. Out of the results obtained, some conclusions and recommendations related to the design of massive dikes are proposed.
Abstract: The group invariant solution for Prandtl-s boundary layer equations for an incompressible fluid governing the flow in radial free, wall and liquid jets having finite fluid velocity at the orifice are investigated. For each jet a symmetry is associated with the conserved vector that was used to derive the conserved quantity for the jet elsewhere. This symmetry is then used to construct the group invariant solution for the third-order partial differential equation for the stream function. The general form of the group invariant solution for radial jet flows is derived. The general form of group invariant solution and the general form of the similarity solution which was obtained elsewhere are the same.
Abstract: Mobile robots are used in a large field of scenarios,
like exploring contaminated areas, repairing oil rigs under water,
finding survivors in collapsed buildings, etc. Currently, there is no
unified intuitive user interface (UI) to control such complex mobile
robots. As a consequence, some scenarios are done without the
exploitation of experience and intuition of human teleoperators.
A novel framework has been developed to embed a flexible and
modular UI into a complete 3-D virtual reality simulation system.
This new approach wants to access maximum benefits of human
operators. Sensor information received from the robot is prepared for
an intuitive visualization. Virtual reality metaphors support the
operator in his decisions. These metaphors are integrated into a real
time stereo video stream. This approach is not restricted to any
specific type of mobile robot and allows for the operation of different
robot types with a consistent concept and user interface.
Abstract: The present project was conducted with the
circumferential-fuel-jets inverse diffusion flame (CIDF) burner
burning liquefied petroleum gas (LPG) enriched with 50% of
hydrogen fuel (H2). The range of stable operation of the CIDF burner
in terms of Reynolds number (from laminar to turbulent flow regions),
equivalence ratio and fuel jet velocity of LPG of the 50% H2-LPG
mixed fuel was identified. Experiments were also carried out to
investigate the flame structures of the LPG flame and LPG enriched H2
flame. Experimental results obtained from these two flames were
compared to fully explore the influence of hydrogen addition on flame
stability. Flame heights obtained by burning these two kinds of fuels at
various equivalence ratios were compared and correlated with the
Global Momentum Ratio (GMR).
Abstract: Swedish truck industry is investigating the possibility
for implementing the use of Compacted Graphite Iron (CGI) in their
heavy duty diesel engines. Compared to the alloyed gray iron used
today, CGI has superior mechanical properties but not as good
machinability. Another issue that needs to be addressed when
implementing CGI is the inhomogeneous microstructure when the
cast component has different section thicknesses, as in cylinder
blocks. Thinner sections results in finer pearlite, in the material, with
higher strength. Therefore an investigation on its influence on
machinability was needed. This paper focuses on the effect that
interlamellar distance in pearlite has on CGI machinability and
material physical properties. The effect of pearlite content and
nodularity is also examined. The results showed that interlamellar
distance in pearlite did not have as large effect on the material
physical properties or machinability as pearlite content. The paper
also shows the difficulties of obtaining a homogeneous
microstructure in inhomogeneous workpieces.
Abstract: A proposed small-signal model parameters for a pseudomorphic high electron mobility transistor (PHEMT) is presented. Both extrinsic and intrinsic circuit elements of a smallsignal model are determined using genetic algorithm (GA) as a stochastic global search and optimization tool. The parameters extraction of the small-signal model is performed on 200-μm gate width AlGaAs/InGaAs PHEMT. The equivalent circuit elements for a proposed 18 elements model are determined directly from the measured S- parameters. The GA is used to extract the parameters of the proposed small-signal model from 0.5 up to 18 GHz.
Abstract: Investigations of the unimolecular decomposition of
vinyl ethyl ether (VEE), vinyl propyl ether (VPE) and vinyl butyl
ether (VBE) have shown that activation of the molecule of a ether
results in formation of a cyclic construction - the transition state (TS),
which may lead to the displacement of the thermodynamic
equilibrium towards the reaction products. The TS is obtained by
applying energy minimization relative to the ground state of an ether
under the program MM2 when taking into account the hydrogen bond
formation between a hydrogen atom of alkyl residue and the extreme
atom of carbon of the vinyl group. The dissociation of TS up to the
products is studied by energy minimization procedure using the
mathematical program Gaussian. The obtained calculation data for
VEE testify that the decomposition of this ether may be conditioned
by hydrogen bond formation for two possible versions: when α- or β-
hydrogen atoms of the ethyl group are bound to carbon atom of the
vinyl group. Applying the same calculation methods to other ethers
(VPE and VBE) it is shown that only in the case of hydrogen bonding
between α-hydrogen atom of the alkyl residue and the extreme atom
of carbon of the vinyl group (αH---C) results in decay of theses
ethers.
Abstract: Air conditioning is mainly to be used as human
comfort medium. It has been use more often in country in which the
daily temperatures are high. In scientific, air conditioning is defined
as a process of controlling the moisture, cooling, heating and cleaning
air. Without proper estimation of cooling load, big amount of waste
energy been used because of unsuitable of air conditioning system are
not considering to overcoming heat gains from surrounding. This is
due to the size of the room is too big and the air conditioning has to
use more energy to cool the room and the air conditioning is too
small for the room. The studies are basically to develop a program to
calculate cooling load. Through this study it is easy to calculate
cooling load estimation. Furthermore it-s help to compare the cooling
load estimation by hourly and yearly. Base on the last study that been
done, the developed software are not user-friendly. For individual
without proper knowledge of calculating cooling load estimation
might be problem. Easy excess and user-friendly should be the main
objective to design something. This program will allow cooling load
able be estimate by any users rather than estimation by using rule of
thumb. Several of limitation of case study is judged to sure it-s
meeting to Malaysia building specification. Finally validation is done
by comparison manual calculation and by developed program.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.