Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: This paper presents a sensing system for 3D sensing
and mapping by a tracked mobile robot with an arm-type sensor
movable unit and a laser range finder (LRF). The arm-type sensor
movable unit is mounted on the robot and the LRF is installed at the
end of the unit. This system enables the sensor to change position and
orientation so that it avoids occlusions according to terrain by this
mechanism. This sensing system is also able to change the height of
the LRF by keeping its orientation flat for efficient sensing. In this kind
of mapping, it may be difficult for moving robot to apply mapping
algorithms such as the iterative closest point (ICP) because sets of the
2D data at each sensor height may be distant in a common surface. In
order for this kind of mapping, the authors therefore applied
interpolation to generate plausible model data for ICP. The results of
several experiments provided validity of these kinds of sensing and
mapping in this sensing system.
Abstract: We present a dual-band (Cellular & PCS) dual-path
zero-IF receiver for CDMA2000 diversity, monitoring and
simultaneous-GPS. The secondary path is a SAW-less diversity
CDMA receiver which can be also used for advanced features like
monitoring when supported with an additional external VCO. A GPS
receiver is integrated with its dedicated VCO allowing simultaneous
positioning during a cellular call. The circuit is implemented in a
0.25μm 40GHz-fT BiCMOS process and uses a HVQFN 56-pin
package. It consumes a maximum 300mW from a 2.8V supply in
dual-modes. The chip area is 12.8mm2.
Abstract: This paper considers a scheduling problem in flexible
flow shops environment with the aim of minimizing two important
criteria including makespan and cumulative tardiness of jobs. Since
the proposed problem is known as an Np-hard problem in literature,
we have to develop a meta-heuristic to solve it. We considered
general structure of Genetic Algorithm (GA) and developed a new
version of that based on Data Envelopment Analysis (DEA). Two
objective functions assumed as two different inputs for each Decision
Making Unit (DMU). In this paper we focused on efficiency score of
DMUs and efficient frontier concept in DEA technique. After
introducing the method we defined two different scenarios with
considering two types of mutation operator. Also we provided an
experimental design with some computational results to show the
performance of algorithm. The results show that the algorithm
implements in a reasonable time.
Abstract: This paper demonstrates a model of an e-Learning
system based on nowadays learning theory and distant education
practice. The relationships in the model are designed to be simple
and functional and do not necessarily represent any particular e-
Learning environments. It is meant to be a generic e-Learning
system model with implications for any distant education course
instructional design. It allows online instructors to move away from
the discrepancy between the courses and body of knowledge. The
interrelationships of four primary sectors that are at the e-Learning
system are presented in this paper. This integrated model includes
[1] pedagogy, [2] technology, [3] teaching, and [4] learning. There
are interactions within each of these sectors depicted by system loop
map.
Abstract: Public bus service plays a significant role in our
society as people movers and to facilitate travels within towns and districts. The quality of service of public bus is always being
regarded as poor, or rather, underestimated as second class means of transportation. Reliability of service, or the ability to deliver service as planned, is one key element in perceiving the quality of bus service and the punctuality index is one of the performance parameters in determining the service reliability. This study
concentrates on evaluating the reliability performance of bus operation using punctuality index assessment. A week data for each
of six city bus routes is recorded using the on-board methodology to calculate the punctuality index for city bus service in Kota Bharu. The results revealed that the punctuality index for the whole city bus network is 94.25% (LOS B).
Abstract: Technology assessment is a vital part of decision process in manufacturing, particularly for decisions on selection of new sustainable manufacturing processes. To assess these processes, a matrix approach is introduced and sustainability assessment models are developed. Case studies show that the matrix-based approach provides a flexible and practical way for sustainability evaluation of new manufacturing technologies such as those used in surface coating. The technology assessment of coating processes reveals that compared with powder coating, the sol-gel coating can deliver better technical, economical and environmental sustainability with respect to the selected sustainability evaluation criteria for a decorative coating application of car wheels.
Abstract: The objective of this manuscript is to find area under the plasma concentration- time curve (AUC) for multiple doses of salbutamol sulphate sustained release tablets (Ventolin® oral tablets SR 8 mg, GSK, Pakistan) in the group of 18 healthy adults by using computational mathematics techniques. Following the administration of 4 doses of Ventolin® tablets 12 hourly to 24 healthy human subjects and bioanalysis of obtained plasma samples, plasma drug concentration-time profile was constructed. AUC, an important pharmacokinetic parameter, was measured using integrated equation of multiple oral dose regimens. The approximated AUC was also calculated by using computational mathematics techniques such as repeated rectangular, repeated trapezium and repeated Simpson's rule and compared with exact value of AUC calculated by using integrated equation of multiple oral dose regimens to find best computational mathematics method that gives AUC values closest to exact. The exact values of AUC for four consecutive doses of Ventolin® oral tablets were 150.5819473, 157.8131756, 164.4178231 and 162.78 ng.h/ml while the closest values approximated AUC values were 149.245962, 157.336171, 164.2585768 and 162.289224 ng.h/ml, respectively as found by repeated rectangular rule. The errors in the approximated values of AUC were negligible. It is concluded that all computational tools approximated values of AUC accurately but the repeated rectangular rule gives slightly better approximated values of AUC as compared to repeated trapezium and repeated Simpson's rules.
Abstract: In recent years, Radio Frequency Identification (RFID)
is followed with interest by many researches, especially for the
purpose of indoor positioning as the innate properties of RFID are
profitable for achieving it. A lot of algorithms or schemes are proposed
to be used in the RFID-based positioning system, but most of them are
lack of environmental consideration and it induces inaccuracy of
application. In this research, a lot of algorithms and schemes of RFID
indoor positioning are discussed to see whether effective or not on
application, and some rules are summarized for achieving accurate
positioning. On the other hand, a new term “Noise Factor" is involved
to describe the signal loss between the target and the obstacle. As a
result, experimental data can be obtained but not only simulation; and
the performance of the positioning system can be expressed
substantially.
Abstract: In this paper, a new method of controlling position of AC Servomotor using Field Programmable Gate Array (FPGA). FPGA controller is used to generate direction and the number of pulses required to rotate for a given angle. Pulses are sent as a square wave, the number of pulses determines the angle of rotation and frequency of square wave determines the speed of rotation. The proposed control scheme has been realized using XILINX FPGA SPARTAN XC3S400 and tested using MUMA012PIS model Alternating Current (AC) servomotor. Experimental results show that the position of the AC Servo motor can be controlled effectively. KeywordsAlternating Current (AC), Field Programmable Gate Array (FPGA), Liquid Crystal Display (LCD).
Abstract: Road traffic accidents are a major cause of death worldwide. In an attempt to reduce accidents, some research efforts have focused on creating Advanced Driver Assistance Systems (ADAS) able to detect vehicle, driver and environmental conditions and to use this information to identify cues for potential accidents. This paper presents continued work on a novel Non-intrusive Intelligent Driver Assistance and Safety System (Ni-DASS) for assessing driver point of regard within vehicles. It uses an on-board CCD camera to observe the driver-s face. A template matching approach is used to compare the driver-s eye-gaze pattern with a set of eye-gesture templates of the driver looking at different focal points within the vehicle. The windscreen is divided into cells and comparison of the driver-s eye-gaze pattern with templates of a driver-s eyes looking at each cell is used to determine the driver-s point of regard on the windscreen. Results indicate that the proposed technique could be useful in situations where low resolution estimates of driver point of regard are adequate. For instance, To allow ADAS systems to alert the driver if he/she has positively failed to observe a hazard.
Abstract: Assembly line balancing is a very important issue in
mass production systems due to production cost. Although many
studies have been done on this topic, but because assembly line
balancing problems are so complex they are categorized as NP-hard
problems and researchers strongly recommend using heuristic
methods. This paper presents a new heuristic approach called the
critical task method (CTM) for solving U-shape assembly line
balancing problems. The performance of the proposed heuristic
method is tested by solving a number of test problems and comparing
them with 12 other heuristics available in the literature to confirm the
superior performance of the proposed heuristic. Furthermore, to
prove the efficiency of the proposed CTM, the objectives are
increased to minimize the number of workstation (or equivalently
maximize line efficiency), and minimizing the smoothness index.
Finally, it is proven that the proposed heuristic is more efficient than
the others to solve the U-shape assembly line balancing problem.
Abstract: An adaptive Fuzzy Inference Perceptual model has
been proposed for watermarking of digital images. The model
depends on the human visual characteristics of image sub-regions in
the frequency multi-resolution wavelet domain. In the proposed
model, a multi-variable fuzzy based architecture has been designed to
produce a perceptual membership degree for both candidate
embedding sub-regions and strength watermark embedding factor.
Different sizes of benchmark images with different sizes of
watermarks have been applied on the model. Several experimental
attacks have been applied such as JPEG compression, noises and
rotation, to ensure the robustness of the scheme. In addition, the
model has been compared with different watermarking schemes. The
proposed model showed its robustness to attacks and at the same time
achieved a high level of imperceptibility.
Abstract: Nowadays companies strive to survive in a
competitive global environment. To speed up product
development/modifications, it is suggested to adopt a collaborative
product development approach. However, despite the advantages of
new IT improvements still many CAx systems work separately and
locally. Collaborative design and manufacture requires a product
information model that supports related CAx product data models. To
solve this problem many solutions are proposed, which the most
successful one is adopting the STEP standard as a product data model
to develop a collaborative CAx platform. However, the improvement
of the STEP-s Application Protocols (APs) over the time, huge
number of STEP AP-s and cc-s, the high costs of implementation,
costly process for conversion of older CAx software files to the STEP
neutral file format; and lack of STEP knowledge, that usually slows
down the implementation of the STEP standard in collaborative data
exchange, management and integration should be considered. In this
paper the requirements for a successful collaborative CAx system is
discussed. The STEP standard capability for product data integration
and its shortcomings as well as the dominant platforms for supporting
CAx collaboration management and product data integration are
reviewed. Finally a platform named LAYMOD to fulfil the
requirements of CAx collaborative environment and integrating the
product data is proposed. The platform is a layered platform to enable
global collaboration among different CAx software
packages/developers. It also adopts the STEP modular architecture
and the XML data structures to enable collaboration between CAx
software packages as well as overcoming the STEP standard
limitations. The architecture and procedures of LAYMOD platform
to manage collaboration and avoid contradicts in product data
integration are introduced.
Abstract: Langmuir–Blodgett (LB) films of polyaniline (PANI) grown onto ITO coated glass substrates were utilized for the fabrication of Uric acid biosensor for efficient detection of uric acid by immobilizing Uricase via EDC–NHS coupling. The modified electrodes were characterized by atomic force microscopy (AFM). The response characteristics after immobilization of uricase were studied using cyclic voltammetry and electrochemical impedance spectroscopy techniques. The uricase/PANI/ITO/glass bioelectrode studied by CV and EIS techniques revealed detection of uric acid in a wide range of 0.05 mM to 1.0 mM, covering the physiological range in blood. A low Michaelis–Menten constant (Km) of 0.21 mM indicates the higher affinity of immobilized Uricase towards its analyte (uric acid). The fabricated uric acid biosensor based on PANI LB films exhibits excellent sensitivity of 0.21 mA/mM with a response time of 4 s, good reproducibility, long shelf life (8 weeks) and high selectivity.
Abstract: Due to the coexistence of different Radio Access
Technologies (RATs), Next Generation Wireless Networks (NGWN)
are predicted to be heterogeneous in nature. The coexistence of
different RATs requires a need for Common Radio Resource
Management (CRRM) to support the provision of Quality of Service
(QoS) and the efficient utilization of radio resources. RAT selection
algorithms are part of the CRRM algorithms. Simply, their role is to
verify if an incoming call will be suitable to fit into a heterogeneous
wireless network, and to decide which of the available RATs is most
suitable to fit the need of the incoming call and admit it.
Guaranteeing the requirements of QoS for all accepted calls and at
the same time being able to provide the most efficient utilization of
the available radio resources is the goal of RAT selection algorithm.
The normal call admission control algorithms are designed for
homogeneous wireless networks and they do not provide a solution
to fit a heterogeneous wireless network which represents the NGWN.
Therefore, there is a need to develop RAT selection algorithm for
heterogeneous wireless network. In this paper, we propose an
approach for RAT selection which includes receiving different
criteria, assessing and making decisions, then selecting the most
suitable RAT for incoming calls. A comprehensive survey of
different RAT selection algorithms for a heterogeneous wireless
network is studied.
Abstract: Visual inputs are one of the key sources from which
humans perceive the environment and 'understand' what is
happening. Artificial systems perceive the visual inputs as digital
images. The images need to be processed and analysed. Within the
human brain, processing of visual inputs and subsequent
development of perception is one of its major functionalities. In this
paper we present part of our research project, which aims at the
development of an artificial model for visual perception (or
'understanding') based on the human perceptive and cognitive
systems. We propose a new model for perception from visual inputs
and a way of understaning or interpreting images using the model.
We demonstrate the implementation and use of the model with a real
image data set.
Abstract: The applications on numbers are across-the-board that there is much scope for study. The chic of writing numbers is diverse and comes in a variety of form, size and fonts. Identification of Indian languages scripts is challenging problems. In Optical Character Recognition [OCR], machine printed or handwritten characters/numerals are recognized. There are plentiful approaches that deal with problem of detection of numerals/character depending on the sort of feature extracted and different way of extracting them. This paper proposes a recognition scheme for handwritten Hindi (devnagiri) numerals; most admired one in Indian subcontinent our work focused on a technique in feature extraction i.e. Local-based approach, a method using 16-segment display concept, which is extracted from halftoned images & Binary images of isolated numerals. These feature vectors are fed to neural classifier model that has been trained to recognize a Hindi numeral. The archetype of system has been tested on varieties of image of numerals. Experimentation result shows that recognition rate of halftoned images is 98 % compared to binary images (95%).
Abstract: terrorism and extremism are among the most
dangerous and difficult to forecast the phenomena of our time, which
are becoming more diverse forms and rampant. Terrorist attacks often
produce mass casualties, involve the destruction of material and
spiritual values, beyond the recovery times, sow hatred among
nations, provoke war, mistrust and hatred between the social and
national groups, which sometimes can not be overcome within a
generation. Currently, the countries of Central Asia are a topical issue
– the threat of terrorism and religious extremism, which grow not
only in our area, but throughout the world. Of course, in each of the
terrorist threat is assessed differently. In our country the problem of
terrorism should not be acutely. Thus, after independence and
sovereignty of Kazakhstan has chosen the path of democracy,
progress and free economy. With the policy of the President of
Kazakhstan Nursultan Nazarbayev and well-organized political and
economic reforms, there has been economic growth and rising living
standards, socio-political stability, ensured civil peace and accord in
society [1].