Abstract: The sustainability of a place depends on a series of factors which contribute to the quality of life, sense of place and recognition of identity. An activity like walking, which in itself is obviously ''sustainable'', can become non sustainable if the context in which it is carried out does not meet the conditions for an adequate quality of life. This work is aimed at proposing the analytical method of Place Maker to identify the elements that do not feature in traditional mapping and which constitute the contemporary identity of the places, and the relative complex map to represent those elements and support sustainable urban identity design. The method's potential for areas with a predominantly pedestrian vocation is illustrated by means of the case study of the Ramblas in Barcelona.
Abstract: This paper aims to explain the project carried out at
the University of Cordoba, specifically at the High Polytechnic
School in collaboration with two other organizations belonging to the
Andalusian Ministry of Innovation, Science and Business:
Andalusian Innovation and Development Agency (IDEA agency) [1]
and the Territorial Net of Entrepreneurship Support (in Spanish Red
Territorial de Apoyo al Emprendedor) [11].
The project is being developed in several stages of which only the
first one has already been completed. However, several important
preliminary results derive from it, based mainly in the description of
the nature of entrepreneurship in the field of university education and
its impact on student-s competency as recommended by the European
Higher Education Area. Some problems holding back the correct
future development will also be shown as derived from the specific
context of application of the project.
Abstract: Cenozoic basalts found in Jiangsu province of eastern
China include tholeiites and alkali basalts. The present paper analyzed
the major, trace elements, rare earth elements of these Cenozoic
basalts and combined with Sr-Nd isotopic compositions proposed by
Chen et al. (1990)[1] in the literatures to discuss the petrogenesis of
these basalts and the geochemical characteristics of the source mantle.
Based on major, trace elements and fractional crystallization model
established by Brooks and Nielsen (1982)[2] we suggest that the
basaltic magma has experienced olivine + clinopyroxene fractionation
during its evolution. The chemical compositions of basaltic rocks from
Jiangsu province indicate that these basalts may belong to the same
magmatic system. Spidergrams reveal that Cenozoic basalts from
Jiangsu province have geochemical characteristics similar to those of
ocean island basalts(OIB). The slight positive Nb and Ti anomalies
found in basaltic rocks of this study suggest the presence of Ti-bearing
minerals in the mantle source and these Ti-bearing minerals had
contributed to basaltic magma during partial melting, indicating a
metasomatic event might have occurred before the partial melting.
Based on the Sr vs. Nd isotopic ratio plots, we suggest that Jiangsu
basalts may be derived from partial melting of mantle source which
may represent two-end members mixing of DMM and EM-I. Some
Jiangsu basaltic magma may be derived from partial melting of EM-I
heated by the upwelling asthenospheric mantle or asthenospheric
diapirism.
Abstract: This paper introduces a hand gesture recognition system to recognize real time gesture in unstrained environments. Efforts should be made to adapt computers to our natural means of communication: Speech and body language. A simple and fast algorithm using orientation histograms will be developed. It will recognize a subset of MAL static hand gestures. A pattern recognition system will be using a transforrn that converts an image into a feature vector, which will be compared with the feature vectors of a training set of gestures. The final system will be Perceptron implementation in MATLAB. This paper includes experiments of 33 hand postures and discusses the results. Experiments shows that the system can achieve a 90% recognition average rate and is suitable for real time applications.
Abstract: Quality Function Deployment (QFD) is an expounded, multi-step planning method for delivering commodity, services, and processes to customers, both external and internal to an organization. It is a way to convert between the diverse customer languages expressing demands (Voice of the Customer), and the organization-s languages expressing results that sate those demands. The policy is to establish one or more matrices that inter-relate producer and consumer reciprocal expectations. Due to its visual presence is called the “House of Quality" (HOQ). In this paper, we assumed HOQ in multi attribute decision making (MADM) pattern and through a proposed MADM method, rank technical specifications. Thereafter compute satisfaction degree of customer requirements and for it, we apply vagueness and uncertainty conditions in decision making by fuzzy set theory. This approach would propound supervised neural network (perceptron) for MADM problem solving.
Abstract: Gene, principal unit of inheritance, is an ordered
sequence of nucleotides. The genes of eukaryotic organisms include
alternating segments of exons and introns. The region of
Deoxyribonucleic acid (DNA) within a gene containing instructions
for coding a protein is called exon. On the other hand, non-coding
regions called introns are another part of DNA that regulates gene
expression by removing from the messenger Ribonucleic acid (RNA)
in a splicing process. This paper proposes to determine splice
junctions that are exon-intron boundaries by analyzing DNA
sequences. A splice junction can be either exon-intron (EI) or intron
exon (IE). Because of the popularity and compatibility of the
artificial neural network (ANN) in genetic fields; various ANN
models are applied in this research. Multi-layer Perceptron (MLP),
Radial Basis Function (RBF) and Generalized Regression Neural
Networks (GRNN) are used to analyze and detect the splice junctions
of gene sequences. 10-fold cross validation is used to demonstrate
the accuracy of networks. The real performances of these networks
are found by applying Receiver Operating Characteristic (ROC)
analysis.
Abstract: The purpose of this paper is to present two different
approaches of financial distress pre-warning models appropriate for
risk supervisors, investors and policy makers. We examine a sample
of the financial institutions and electronic companies of Taiwan
Security Exchange (TSE) market from 2002 through 2008. We
present a binary logistic regression with paned data analysis. With
the pooled binary logistic regression we build a model including
more variables in the regression than with random effects, while the
in-sample and out-sample forecasting performance is higher in
random effects estimation than in pooled regression. On the other
hand we estimate an Adaptive Neuro-Fuzzy Inference System
(ANFIS) with Gaussian and Generalized Bell (Gbell) functions and
we find that ANFIS outperforms significant Logit regressions in both
in-sample and out-of-sample periods, indicating that ANFIS is a
more appropriate tool for financial risk managers and for the
economic policy makers in central banks and national statistical
services.
Abstract: This paper aims to (1) analyze the profiles of
transgressors (detected evaders); (2) examine reason(s) that triggered a
tax audit, causes of tax evasion, audit timeframe and tax penalty
charged; and (3) to assess if tax auditors followed the guidelines as
stated in the 'Tax Audit Framework' when conducting tax audits. In
2011, the Inland Revenue Board Malaysia (IRBM) had audited and
finalized 557 company cases. With official permission, data of all the
557 cases were obtained from the IRBM. Of these, a total of 421 cases
with complete information were analyzed. About 58.1% was small and
medium corporations and from the construction industry (32.8%). The
selection for tax audit was based on risk analysis (66.8%), information
from third party (11.1%), and firm with low profitability or fluctuating
profit pattern (7.8%). The three persistent causes of tax evasion by
firms were over claimed expenses (46.8%), fraudulent reporting of
income (38.5%) and overstating purchases (10.5%). These findings
are consistent with past literature. Results showed that tax auditors
took six to 18 months to close audit cases. More than half of tax
evaders were fined 45% on additional tax raised during audit for the
first offence. The study found tax auditors did follow the guidelines in
the 'Tax Audit Framework' in audit selection, settlement and penalty
imposition.
Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: This paper presents an investigation of the power
penalties imposed by four-wave mixing (FWM) on G.652 (Single-
Mode Fiber - SMF), G.653 (Dispersion-Shifted Fiber - DSF), and
G.655 (Non-Zero Dispersion-Shifted Fiber - NZDSF) compliant
fibers, considering the DWDM grids suggested by the ITU-T
Recommendations G.692, and G.694.1, with uniform channel
spacing of 100, 50, 25, and 12.5 GHz. The mathematical/numerical
model assumes undepleted pumping, and shows very clearly the
deleterious effect of FWM on the performance of DWDM systems,
measured by the signal-to-noise ratio (SNR). The results make it
evident that non-uniform channel spacing is practically mandatory
for WDM systems based on DSF fibers.
Abstract: The aim of this study is evaluating the antinociceptive
and anti-inflamatory activity of Geum kokanicum. After
determination total extract LD50, different doses of extract were
chosen for intrapritoneal injections. In inflammation test, male NMRI
mice were divided into 6 groups: control (normal saline), positive
control (Dexamethasone 15mg/kg), and total extract (0.025, 0.05,
0.1, and 0.2 gr/kg). The inflammation was produced by xyleneinduced
edema. In order to evaluate the antinociceptive effect of total
extract, formalin test was used. Mice were divided into 6 groups:
control, positive control (morphine 10mg/kg), and 4 groups which
received total extract. Then they received Formalin. The animals
were observed for the reaction to pain. Data were analyzed using
One-way ANOVA followed by Tukey-Kramer multiple comparison
test. LD50 was 1 gr/kg. Data indicated that 0.5,0.1 and 0.2 gr/kg
doses of total extract have particular antinociceptive and antiinflammatory
effects in a comparison with control (P
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: The algorithm represents the DCT coefficients to concentrate signal energy and proposes combination and dictator to eliminate the correlation in the same level subband for encoding the DCT-based images. This work adopts DCT and modifies the SPIHT algorithm to encode DCT coefficients. The proposed algorithm also provides the enhancement function in low bit rate in order to improve the perceptual quality. Experimental results indicate that the proposed technique improves the quality of the reconstructed image in terms of both PSNR and the perceptual results close to JPEG2000 at the same bit rate.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.
Abstract: We consider a heterogeneously mixing SIR stochastic
epidemic process in populations described by a general graph.
Likelihood theory is developed to facilitate statistic inference for the
parameters of the model under complete observation. We show that
these estimators are asymptotically Gaussian unbiased estimates by
using a martingale central limit theorem.
Abstract: Automatic face detection is a complex problem in
image processing. Many methods exist to solve this problem such as
template matching, Fisher Linear Discriminate, Neural Networks,
SVM, and MRC. Success has been achieved with each method to
varying degrees and complexities. In proposed algorithm we used
upright, frontal faces for single gray scale images with decent
resolution and under good lighting condition. In the field of face
recognition technique the single face is matched with single face
from the training dataset. The author proposed a neural network
based face detection algorithm from the photographs as well as if any
test data appears it check from the online scanned training dataset.
Experimental result shows that the algorithm detected up to 95%
accuracy for any image.