Abstract: Experimental & numeral study of temperature
distribution during milling process, is important in milling quality
and tools life aspects. In the present study the milling cross-section
temperature is determined by using Artificial Neural Networks
(ANN) according to the temperature of certain points of the work
piece and the point specifications and the milling rotational speed of
the blade. In the present work, at first three-dimensional model of the
work piece is provided and then by using the Computational Heat
Transfer (CHT) simulations, temperature in different nods of the
work piece are specified in steady-state conditions. Results obtained
from CHT are used for training and testing the ANN approach. Using
reverse engineering and setting the desired x, y, z and the milling
rotational speed of the blade as input data to the network, the milling
surface temperature determined by neural network is presented as
output data. The desired points temperature for different milling
blade rotational speed are obtained experimentally and by
extrapolation method for the milling surface temperature is obtained
and a comparison is performed among the soft programming ANN,
CHT results and experimental data and it is observed that ANN soft
programming code can be used more efficiently to determine the
temperature in a milling process.
Abstract: Formal verification is proposed to ensure the
correctness of the design and make functional verification more
efficient. As cache plays a vital role in the design of System on Chip
(SoC), and cache with Memory Management Unit (MMU) and cache
memory unit makes the state space too large for simulation to verify,
then a formal verification is presented for such system design. In the
paper, a formal model checking verification flow is suggested and a
new cache memory model which is called “exhaustive search model”
is proposed. Instead of using large size ram to denote the whole cache
memory, exhaustive search model employs just two cache blocks. For
cache system contains data cache (Dcache) and instruction cache
(Icache), Dcache memory model and Icache memory model are
established separately using the same mechanism. At last, the novel
model is employed to the verification of a cache which is module of a
custom-built SoC system that has been applied in practical, and the
result shows that the cache system is verified correctly using the
exhaustive search model, and it makes the verification much more
manageable and flexible.
Abstract: Operations, maintenance and reliability of wind
turbines have received much attention over the years due to the rapid
expansion of wind farms. This paper explores early fault diagnosis
technique for a 5MW wind turbine system subjected to multiple
faults, where genetic optimization algorithm is employed to make the
residual sensitive to the faults, but robust against disturbances. The
proposed technique has a potential to reduce the downtime mostly
caused by the breakdown of components and exploit the productivity
consistency by providing timely fault alarms. Simulation results show
the effectiveness of the robust fault detection methods used under
Matlab/Simulink/Gatool environment.
Abstract: ESPRIT-TLS method appears a good choice for high
resolution fault detection in induction machines. It has a very high
effectiveness in the frequency and amplitude identification.
Contrariwise, it presents a high computation complexity which
affects its implementation in real time fault diagnosis. To avoid this
problem, a Fast-ESPRIT algorithm that combined the IIR band-pass
filtering technique, the decimation technique and the original
ESPRIT-TLS method was employed to enhance extracting accurately
frequencies and their magnitudes from the wind stator current with
less computation cost. The proposed algorithm has been applied to
verify the wind turbine machine need in the implementation of an online,
fast, and proactive condition monitoring. This type of remote
and periodic maintenance provides an acceptable machine lifetime,
minimize its downtimes and maximize its productivity. The
developed technique has evaluated by computer simulations under
many fault scenarios. Study results prove the performance of Fast-
ESPRIT offering rapid and high resolution harmonics recognizing
with minimum computation time and less memory cost.
Abstract: Organic Rankine Cycle (ORC) is the most commonly used method for recovering energy from small sources of heat. The investigation of the ORC in supercritical condition is a new research area as it has a potential to generate high power and thermal efficiency in a waste heat recovery system. This paper presents a steady state ORC model in supercritical condition and its simulations with a real engine’s exhaust data. The key component of ORC, evaporator, is modelled using finite volume method, modelling of all other components of the waste heat recovery system such as pump, expander and condenser are also presented. The aim of this paper is to investigate the effects of mass flow rate and evaporator outlet temperature on the efficiency of the waste heat recovery process. Additionally, the necessity of maintaining an optimum evaporator outlet temperature is also investigated. Simulation results show that modification of mass flow rate is the key to changing the operating temperature at the evaporator outlet.
Abstract: The Blue Nile Basin is the most important tributary of
the Nile River. Egypt and Sudan are almost dependent on water
originated from the Blue Nile. This multi-dependency creates
conflicts among the three countries Egypt, Sudan, and Ethiopia
making the management of these conflicts as an international issue.
Good assessment of the water resources of the Blue Nile is an
important to help in managing such conflicts. Hydrological models
are good tool for such assessment. This paper presents a critical
review of the nature and variability of the climate and hydrology of
the Blue Nile Basin as a first step of using hydrological modeling to
assess the water resources of the Blue Nile. Many several attempts
are done to develop basin-scale hydrological modeling on the Blue
Nile. Lumped and semi distributed models used averages of
meteorological inputs and watershed characteristics in hydrological
simulation, to analyze runoff for flood control and water resource
management. Distributed models include the temporal and spatial
variability of catchment conditions and meteorological inputs to
allow better representation of the hydrological process. The main
challenge of all used models was to assess the water resources of the
basin is the shortage of the data needed for models calibration and
validation. It is recommended to use distributed model for their
higher accuracy to cope with the great variability and complexity of
the Blue Nile basin and to collect sufficient data to have more
sophisticated and accurate hydrological modeling.
Abstract: This paper presents two types of microstrip bandpass
filter (BPF) at microwave frequencies. The first one is a tunable BPF
using planar patch resonators based on a varactor diode. The filter is
formed by a triple mode circular patch resonator with two pairs of
slots, in which the varactor diodes are connected. Indeed, this filter is
initially centered at 2.4 GHz; the center frequency of the tunable
patch filter could be tuned up to 1.8 GHz simultaneously with the
bandwidth, reaching high tuning ranges. Lossless simulations were
compared to those considering the substrate dielectric, conductor
losses and the equivalent electrical circuit model of the tuning
element in order to assess their effects. Within these variations,
simulation results showed insertion loss better than 2 dB and return
loss better than 10 dB over the passband. The second structure is a
BPF for ultra-wideband (UWB) applications based on multiple-mode
resonator (MMR) and rectangular-shaped defected ground structure
(DGS). This filter, which is compact size of 25.2 x 3.8 mm2, provides
in the pass band an insertion loss of 0.57 dB and a return loss greater
than 12 dB. The proposed filters presents good performances and the
simulation results are in satisfactory agreement with the
experimentation ones reported elsewhere.
Abstract: Total hip replacement had been one of the most
successful operations in hip arthritis surgery. The purpose of this
research had been to develop a dynamic hip contact of Thai femoral
bone to analyze the stress distribution on the implant and the strain
distribution on the bone model under daily activities and compared
with the static load simulation. The results showed the different of
maximum von Mises stress 0.14 percent under walking and 0.03
percent under climbing stair condition and the different of equivalent
total strain 0.52 percent under walking and 0.05 percent under
climbing stair condition. The muscular forces should be evaluated
with dynamic condition to reduce the maximum von Mises stress and
equivalent total strain.
Abstract: Many aluminum motorcycle parts produced by a high
pressure die casting. Some parts such as fuel caps were a thin and
complex shape. This part risked for porosities and blisters on surface
if it only depended on an experience of mold makers for mold design.
This research attempted to use CAST-DESIGNER software
simulated the high pressure die casting process with the same process
parameters of a motorcycle fuel cap production. The simulated results
were compared with fuel cap products and expressed the same
porosity and blister locations on cap surface. An average of absolute
difference of simulated results was obtained 0.094 mm when
compared the simulated porosity and blister defect sizes on the fuel
cap surfaces with the experimental micro photography. This
comparison confirmed an accuracy of software and will use the
setting parameters to improve fuel cap molds in the further work.
Abstract: Vehicular Adhoc Network (VANET) is a new
technology which aims to ensure intelligent inter-vehicle
communications, seamless internet connectivity leading to improved
road safety, essential alerts, and access to comfort and entertainment.
VANET operations are hindered by mobile node’s (vehicles)
uncertain mobility. Routing algorithms use metrics to evaluate which
path is best for packets to travel. Metrics like path length (hop count),
delay, reliability, bandwidth, and load determine optimal route. The
proposed scheme exploits link quality, traffic density, and
intersections as routing metrics to determine next hop. This study
enhances Geographical Routing Protocol (GRP) using fuzzy
controllers while rules are optimized with Bee Swarm Optimization
(BSO). Simulations results are compared to conventional GRP.
Abstract: In this paper, an analysis of some model order
reduction techniques is presented. A new hybrid algorithm for model
order reduction of linear time invariant systems is compared with the
conventional techniques namely Balanced Truncation, Hankel Norm
reduction and Dominant Pole Algorithm (DPA). The proposed hybrid
algorithm is known as Clustering Dominant Pole Algorithm (CDPA),
is able to compute the full set of dominant poles and its cluster center
efficiently. The dominant poles of a transfer function are specific
eigenvalues of the state space matrix of the corresponding dynamical
system. The effectiveness of this novel technique is shown through
the simulation results.
Abstract: The wear measuring and wear modelling are
fundamental issues in the industrial field, mainly correlated to the
economy and safety. Therefore, there is a need to study the wear
measurements and wear estimation. Pin-on-disc test is the most
common test which is used to study the wear behaviour. In this paper,
the pin-on-disc (AEROTECH UNIDEX 11) is used for the
investigation of the effects of normal load and hardness of material on
the wear under dry and sliding conditions. In the pin-on-disc rig, two
specimens were used; one, a pin is made of steel with a tip, positioned
perpendicular to the disc, where the disc is made of aluminium. The
pin wear and disc wear were measured by using the following
instruments: The Talysurf instrument, a digital microscope, and the
alicona instrument. The Talysurf profilometer was used to measure
the pin/disc wear scar depth, digital microscope was used to measure
the diameter and width of wear scar, and the alicona was used to
measure the pin wear and disc wear. After that, the Archard model,
American Society for Testing and Materials model (ASTM), and
neural network model were used for pin/disc wear modelling.
Simulation results were implemented by using the Matlab program.
This paper focuses on how the alicona can be used for wear
measurements and how the neural network can be used for wear
estimation.
Abstract: In order to study the aerodynamic performance of a
semi-flexible membrane wing, Fluid-Structure Interaction simulations
have been performed. The fluid problem has been modeled using
two different approaches which are the vortex panel method and the
numerical solution of the Navier-Stokes equations. Nonlinear analysis
of the structural problem is performed using the Finite Element
Method. Comparison between the two fluid solvers has been made.
Aerodynamic performance of the wing is discussed regarding its
lift and drag coefficients and they are compared with those of the
equivalent rigid wing.
Abstract: This article is trying to determine the status of flue gas
that is entering the KWH heat exchanger from combustion chamber
in order to calculate the heat transfer ratio of the heat exchanger.
Combination of measurement, calculation and computer simulation
was used to create a useful way to approximate the heat transfer rate.
The measurements were taken by a number of sensors that are
mounted on the experimental device and by a thermal imaging
camera. The results of the numerical calculation are in a good
correspondence with the real power output of the experimental
device. That result shows that the research has a good direction and
can be used to propose changes in the construction of the heat
exchanger, but still needs enhancements.
Abstract: This paper presents the simulation results of the
effects of sampling frequency on the total harmonic distortion (THD)
of three-phase inverters using the space vector pulse width
modulation (SVPWM) and space vector control (SVC) algorithms.
The relationship between the variables was studied using curve fitting
techniques, and it has been shown that, for 50 Hz inverters, there is
an exponential relation between the sampling frequency and THD up
to around 8500 Hz, beyond which the performance of the model
becomes irregular, and there is an negative exponential relation
between the sampling frequency and the marginal improvement to
the THD. It has also been found that the performance of SVPWM is
better than that of SVC with the same sampling frequency in most
frequency range, including the range where the performance of the
former is irregular.
Abstract: This paper presents a method of hardening the 8051
micro-controller, able to assure reliable operation in the presence of
bit flips caused by radiation. Aiming at avoiding such faults in the
8051 micro-controller, Hamming code protection was used in its
SRAM memory and registers. A VHDL code has been used for this
hamming code protection.
Abstract: Cell volume, together with membrane potential and
intracellular hydrogen ion concentration, is an essential biophysical
parameter for normal cellular activity. Cell volumes can be altered by
osmotically active compounds and extracellular tonicity.
In this study, a simple mathematical model of osmotically induced
cell swelling and shrinking is presented. Emphasis is given to water
diffusion across the membrane. The mathematical description of the
cellular behavior consists in a system of coupled ordinary differential
equations. We compare experimental data of cell volume alterations
driven by differences in osmotic pressure with mathematical
simulations under hypotonic and hypertonic conditions. Implications
for a future model are also discussed.
Abstract: An investigation into Cahn-Hilliard equation was
carried out through numerical simulation to identify a possible phase
separation for one and two dimensional domains. It was observed that
this equation can reproduce important mass fluxes necessary for
phase separation within the miscibility gap and for coalescence of
particles.
Abstract: For the treatment of acute and chronic lung diseases it is preferred to deliver medicaments by inhalation. The drug is delivered directly to tracheobronchial tree. This way allows the given medicament to get directly into the place of action and it makes rapid onset of action and maximum efficiency. The transport of aerosol particles in the particular part of the lung is influenced by their size, anatomy of the lungs, breathing pattern and airway resistance. This article deals with calculation of airway resistance in the lung model of Horsfield. It solves the problem of determination of the pressure losses in bifurcation and thus defines the pressure drop at a given location in the bronchial tree. The obtained data will be used as boundary conditions for transport of aerosol particles in a central part of bronchial tree realized by Computational Fluid Dynamics (CFD) approach. The results obtained from CFD simulation will allow us to provide information on the required particle size and optimal inhalation technique for particle transport into particular part of the lung.
Abstract: Geometric and mechanical properties all influence the
resistance of RC structures and may, in certain combination of
property values, increase the risk of a brittle failure of the whole
system.
This paper presents a statistical and probabilistic investigation on
the resistance of RC beams designed according to Eurocodes 2 and 8,
and subjected to multiple failure modes, under both the natural
variation of material properties and the uncertainty associated with
cross-section and transverse reinforcement geometry. A full
probabilistic model based on JCSS Probabilistic Model Code is
derived. Different beams are studied through material nonlinear
analysis via Monte Carlo simulations. The resistance model is
consistent with Eurocode 2. Both a multivariate statistical evaluation
and the data clustering analysis of outcomes are then performed.
Results show that the ultimate load behaviour of RC beams
subjected to flexural and shear failure modes seems to be mainly
influenced by the combination of the mechanical properties of both
longitudinal reinforcement and stirrups, and the tensile strength of
concrete, of which the latter appears to affect the overall response of
the system in a nonlinear way. The model uncertainty of the
resistance model used in the analysis plays undoubtedly an important
role in interpreting results.