Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.
Abstract: The western Tombolo of the Giens peninsula in
southern France, known as Almanarre beach, is subject to coastal
erosion. We are trying to use computer simulation in order to propose
solutions to stop this erosion. Our aim was first to determine the main
factors for this erosion and successfully apply a coupled hydrosedimentological
numerical model based on observations and
measurements that have been performed on the site for decades.
We have gathered all available information and data about waves,
winds, currents, tides, bathymetry, coastal line, and sediments
concerning the site. These have been divided into two sets: one
devoted to calibrating a numerical model using Mike 21 software, the
other to serve as a reference in order to numerically compare the
present situation to what it could be if we implemented different
types of underwater constructions.
This paper presents the first part of the study: selecting and
melting different sources into a coherent data basis, identifying the
main erosion factors, and calibrating the coupled software model
against the selected reference period.
Our results bring calibration of the numerical model with good
fitting coefficients. They also show that the winter South-Western
storm events conjugated to depressive weather conditions constitute a
major factor of erosion, mainly due to wave impact in the northern
part of the Almanarre beach. Together, current and wind impact is
shown negligible.
Abstract: The tombolo of Giens is located in the town of Hyères
(France). We recall the history of coastal erosion, and prominent
factors affecting the evolution of the western tombolo. We then
discuss the possibility of stabilizing the western tombolo. Our
argumentation relies on a coupled model integrating swells, currents,
water levels and sediment transport. We present the conclusions of
the simulations of various scenarios, including pre-existing
propositions from coastal engineering offices. We conclude that
beach replenishment seems to be necessary but not sufficient for the
stabilization of the beach. Breakwaters reveal effective particularly in
the most exposed northern area. Some solutions fulfill conditions so
as to be elected as satisfactory. We give a comparative analysis of the
efficiency of 14 alternatives for the protection of the tombolo.
Abstract: The Great East Japan Earthquake occurred at 14:46 on Friday, March 11, 2011. It was the most powerful known earthquake to have hit Japan. The earthquake triggered extremely destructive tsunami waves of up to 40.5 meters in height. We focus on the ship’s evacuation from tsunami. Then we analyze about ships evacuation from tsunami using multi-agent simulation and we want to prepare for a coming earthquake. We developed a simulation model of ships that set sail from the port in order to evacuate from the tsunami considering the ship carrying dangerous goods.
Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: Advanced head and neck cancers are aggressive
tumours, which require aggressive treatment. Treatment efficiency is
often hindered by cancer cell repopulation during radiotherapy,
which is due to various mechanisms triggered by the loss of tumour
cells and involves both stem and differentiated cells. The aim of the
current paper is to present in silico simulations of radiotherapy
schedules on a virtual head and neck tumour grown with biologically
realistic kinetic parameters. Using the linear quadratic formalism of
cell survival after radiotherapy, altered fractionation schedules
employing various treatment breaks for normal tissue recovery are
simulated and repopulation mechanism implemented in order to
evaluate the impact of various cancer cell contribution on tumour
behaviour during irradiation. The model has shown that the timing of
treatment breaks is an important factor influencing tumour control in
rapidly proliferating tissues such as squamous cell carcinomas of the
head and neck. Furthermore, not only stem cells but also
differentiated cells, via the mechanism of abortive division, can
contribute to malignant cell repopulation during treatment.
Abstract: The design and plantwide control of an integrated
plant where the endothermic 1,4-butanediol dehydrogenation and the
exothermic furfural hydrogenation is simultaneously performed in a
single reactor is studied. The reactions can be carried out in an
adiabatic reactor using small hydrogen excess and with reduced
parameter sensitivity. The plant is robust and flexible enough to
allow different production rates of γ-butyrolactone and 2-methyl
furan, keeping high product purities. Rigorous steady state and
dynamic simulations performed in AspenPlus and AspenDynamics to
support the conclusions.
Abstract: Different tools and technologies were implemented
for Crisis Response and Management (CRM) which is generally
using available network infrastructure for information exchange.
Depending on type of disaster or crisis, network infrastructure could
be affected and it could not be able to provide reliable connectivity.
Thus any tool or technology that depends on the connectivity could
not be able to fulfill its functionalities. As a solution, a new message
exchange framework has been developed. Framework provides
offline/online information exchange platform for CRM Information
Systems (CRMIS) and it uses XML compression and packet
prioritization algorithms and is based on open source web
technologies. By introducing offline capabilities to the web
technologies, framework will be able to perform message exchange
on unreliable networks. The experiments done on the simulation
environment provide promising results on low bandwidth networks
(56kbps and 28.8 kbps) with up to 50% packet loss and the solution is
to successfully transfer all the information on these low quality
networks where the traditional 2 and 3 tier applications failed.
Abstract: This paper presents the details of a numerical study of
buckling and post buckling behaviour of laminated carbon fiber
reinforced plastic (CFRP) thin-walled cylindrical shell under axial
compression using asymmetric meshing technique (AMT) by
ABAQUS. AMT is considered to be a new perturbation method to
introduce disturbance without changing geometry, boundary
conditions or loading conditions. Asymmetric meshing affects both
predicted buckling load and buckling mode shapes. Cylindrical shell
having lay-up orientation [0^o/+45^o/-45^o/0^o] with radius to thickness
ratio (R/t) equal to 265 and length to radius ratio (L/R) equal to 1.5 is
analysed numerically. A series of numerical simulations
(experiments) are carried out with symmetric and asymmetric
meshing to study the effect of asymmetric meshing on predicted
buckling behaviour. Asymmetric meshing technique is employed in
both axial direction and circumferential direction separately using
two different methods, first by changing the shell element size and
varying the total number elements, and second by varying the shell
element size and keeping total number of elements constant. The
results of linear analysis (Eigenvalue analysis) and non-linear
analysis (Riks analysis) using symmetric meshing agree well with
analytical results. The results of numerical analysis are presented in
form of non-dimensional load factor, which is the ratio of buckling
load using asymmetric meshing technique to buckling load using
symmetric meshing technique. Using AMT, load factor has about 2%
variation for linear eigenvalue analysis and about 2% variation for
non-linear Riks analysis. The behaviour of load end-shortening curve
for pre-buckling is same for both symmetric and asymmetric meshing
but for asymmetric meshing curve behaviour in post-buckling
becomes extraordinarily complex. The major conclusions are:
different methods of AMT have small influence on predicted
buckling load and significant influence on load displacement curve
behaviour in post buckling; AMT in axial direction and AMT in
circumferential direction have different influence on buckling load
and load displacement curve in post-buckling.
Abstract: This study is used as a definition method to the value
and function in manufacturing sector. In concurrence of discussion
about present condition of modeling method, until now definition of
1D-CAE is ambiguity and not conceptual. Across all the physic fields,
those methods are defined with the formulation of differential
algebraic equation which only applied time derivation and simulation.
At the same time, we propose semi-acausal modeling concept and
differential algebraic equation method as a newly modeling method
which the efficiency has been verified through the comparison of
numerical analysis result between the semi-acausal modeling
calculation and FEM theory calculation.
Abstract: High Peak to Average Power Ratio (PAPR) of the
transmitted signal is a serious problem in multicarrier systems (MC),
such as Orthogonal Frequency Division Multiplexing (OFDM), or in
Multi-Carrier Code Division Multiple Access (MC-CDMA) systems,
due to large number of subcarriers. This effect is possible reduce with
some PAPR reduction techniques. Spreading sequences at the
presence of Saleh and Rapp models of high power amplifier (HPA)
have big influence on the behavior of system. In this paper we
investigate the bit-error-rate (BER) performance of MC-CDMA
systems. Basically we can see from simulations that the MC-CDMA
system with Iterative algorithm can be providing significantly better
results than the MC-CDMA system. The results of our analyses are
verified via simulation.
Abstract: Recent research in neural networks science and
neuroscience for modeling complex time series data and statistical
learning has focused mostly on learning from high input space and
signals. Local linear models are a strong choice for modeling local
nonlinearity in data series. Locally weighted projection regression is
a flexible and powerful algorithm for nonlinear approximation in
high dimensional signal spaces. In this paper, different learning
scenario of one and two dimensional data series with different
distributions are investigated for simulation and further noise is
inputted to data distribution for making different disordered
distribution in time series data and for evaluation of algorithm in
locality prediction of nonlinearity. Then, the performance of this
algorithm is simulated and also when the distribution of data is high
or when the number of data is less the sensitivity of this approach to
data distribution and influence of important parameter of local
validity in this algorithm with different data distribution is explained.
Abstract: Physics Education Research (PER) results have shown
that students do not achieve the expected level of competency in
understanding the concepts of different domains of Physics learning
when taught by the traditional teaching methods, the concepts of
Electricity and Magnetism (E&M) being one among them.
Simulation being one of the valuable instructional tools renders an
opportunity to visualize varied experiences with such concepts.
Considering the electric force concept which requires extensive use
of vector representations, we report here the outcome of the research
results pertaining to the student understanding of this concept and the
role of simulation in using vector representation. The simulation
platform provides a positive impact on the use of vector
representation.
The first stage of this study involves eliciting and analyzing
student responses to questions that probe their understanding of the
concept of electrostatic force and this is followed by four stages of
student interviews as they use the interactive simulations of electric
force in one dimension. Student responses to the questions are
recorded in real time using electronic pad. A validation test interview
is conducted to evaluate students' understanding of the electric force
concept after using interactive simulation. Results indicate lack of
procedural knowledge of the vector representation. The study
emphasizes the need for the choice of appropriate simulation and
mode of induction for learning.
Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: Company managers are always looking for more and
more opportunities to succeed in today's fiercely competitive market.
To maintain your place among the successful companies on the
market today or to come up with a revolutionary business idea is
much more difficult than before. Each new or improved method, tool,
or approach that can improve the functioning of business processes or
even of the entire system is worth checking and verification. The use
of simulation in the design of manufacturing systems and their
management in practice is one of the ways without increased risk,
which makes it possible to find the optimal parameters of
manufacturing processes and systems. The paper presents an example
of use of simulation for solution of the bottleneck problem in the
concrete company.
Abstract: The spring-driven ball-type check valve is one of the
most important components of hydraulic systems: it controls the
position of the ball and prevents backward flow. To simplify the
structure, the spring must be eliminated, and to accomplish this, the
flow pattern and the behavior of the check ball in L-shaped pipe must
be determined. In this paper, we present a full-scale model of a check
ball made of acrylic resin, and we determine the relationship between
the initial position of the ball, the position and diameter of the inflow
port. The check flow rate increases in a standard center inflow model,
and it is possible to greatly decrease the check-flow rate by shifting the
inflow from the center.
Abstract: Job Scheduling plays an important role for efficient
utilization of grid resources available across different domains and
geographical zones. Scheduling of jobs is challenging and NPcomplete.
Evolutionary / Swarm Intelligence algorithms have been
extensively used to address the NP problem in grid scheduling.
Artificial Bee Colony (ABC) has been proposed for optimization
problems based on foraging behaviour of bees. This work proposes a
modified ABC algorithm, Cluster Heterogeneous Earliest First Min-
Min Artificial Bee Colony (CHMM-ABC), to optimally schedule
jobs for the available resources. The proposed model utilizes a novel
Heterogeneous Earliest Finish Time (HEFT) Heuristic Algorithm
along with Min-Min algorithm to identify the initial food source.
Simulation results show the performance improvement of the
proposed algorithm over other swarm intelligence techniques.
Abstract: Fracture in hot precision forging of engine valves was
investigated in this paper. The entire valve forging procedure was
described and the possible cause of the fracture was proposed. Finite
Element simulation was conducted for the forging process, with
commercial Finite Element code DEFORMTM. The effects of
material properties, the effect of strain rate and temperature were
considered in the FE simulation. Two fracture criteria were discussed
and compared, based on the accuracy and reliability of the FE
simulation results. The selected criterion predicted the fracture
location and shows the trend of damage increasing with good
accuracy, which matches the experimental observation. Additional
modification of the punch shapes was proposed to further reduce the
tendency of fracture in forging. Finite Element comparison shows a
great potential of such application in the mass production.
Abstract: Digital image correlation (DIC) is a contactless fullfield
displacement and strain reconstruction technique commonly
used in the field of experimental mechanics. Comparing with
physical measuring devices, such as strain gauges, which only
provide very restricted coverage and are expensive to deploy widely,
the DIC technique provides the result with full-field coverage and
relative high accuracy using an inexpensive and simple experimental
setup. It is very important to study the natural patterns effect on the
DIC technique because the preparation of the artificial patterns is
time consuming and hectic process. The objective of this research is
to study the effect of using images having natural pattern on the
performance of DIC. A systematical simulation method is used to
build simulated deformed images used in DIC. A parameter (subset
size) used in DIC can have an effect on the processing and accuracy
of DIC and even cause DIC to failure. Regarding to the picture
parameters (correlation coefficient), the higher similarity of two
subset can lead the DIC process to fail and make the result more
inaccurate. The pictures with good and bad quality for DIC methods
have been presented and more importantly, it is a systematic way to
evaluate the quality of the picture with natural patterns before they
install the measurement devices.