Abstract: This is a study on numerical simulation of the convection-diffusion transport of a chemical species in steady flow through a small-diameter tube, which is lined with a very thin layer made up of retentive and absorptive materials. The species may be subject to a first-order kinetic reversible phase exchange with the wall material and irreversible absorption into the tube wall. Owing to the velocity shear across the tube section, the chemical species may spread out axially along the tube at a rate much larger than that given by the molecular diffusion; this process is known as dispersion. While the long-time dispersion behavior, well described by the Taylor model, has been extensively studied in the literature, the early development of the dispersion process is by contrast much less investigated. By early development, that means a span of time, after the release of the chemical into the flow, that is shorter than or comparable to the diffusion time scale across the tube section. To understand the early development of the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Flux Corrected Transport Algorithm (FCTA). The computation has enabled us to investigate the combined effects on the early development of the dispersion coefficient due to the reversible and irreversible wall reactions. One of the results is shown that the dispersion coefficient may approach its steady-state limit in a short time under the following conditions: (i) a high value of Damkohler number (say Da ≥ 10); (ii) a small but non-zero value of absorption rate (say Γ* ≤ 0.5).
Abstract: Li1.5Al0.5Ti1.5 (PO4)3(LATP) has received much
attention as a solid electrolyte for lithium batteries. In this study, the
LATP solid electrolyte is prepared by the co-precipitation method
using Li3PO4 as a Li source. The LATP is successfully prepared and
the Li ion conductivities of bulk (inner crystal) and total (inner crystal
and grain boundary) are 1.1 × 10-3 and 1.1 × 10-4 S cm-1, respectively.
These values are comparable to the reported values, in which Li2C2O4
is used as the Li source. It is conclude that the LATP solid electrolyte
can be prepared by the co-precipitation method using Li3PO4 as the Li
source and this procedure has an advantage in mass production over
previous procedure using Li2C2O4 because Li3PO4 is lower price
reagent compared with Li2C2O4.
Abstract: Computed tomography and laminography are heavily investigated in a compressive sensing based image reconstruction framework to reduce the dose to the patients as well as to the radiosensitive devices such as multilayer microelectronic circuit boards. Nowadays researchers are actively working on optimizing the compressive sensing based iterative image reconstruction algorithm to obtain better quality images. However, the effects of the sampled data’s properties on reconstructed the image’s quality, particularly in an insufficient sampled data conditions have not been explored in computed laminography. In this paper, we investigated the effects of two data properties i.e. sampling density and data incoherence on the reconstructed image obtained by conventional computed laminography and a recently proposed method called spherical sinusoidal scanning scheme. We have found that in a compressive sensing based image reconstruction framework, the image quality mainly depends upon the data incoherence when the data is uniformly sampled.
Abstract: Leading topic of this article is description of Lorentz
forces in the container with cuboid and cylindrical shape. Inside of
the container is an electrically conductive melt. This melt is driven by
rotating magnetic field. Input data for comparing Lorentz forces in
the container with cuboid shape were obtained from the computing
program NS-FEM3D, which uses DDS method of computing. Values
of Lorentz forces for container with cylindrical shape were obtained
from inferred analytical formula.
Abstract: In this paper we present a way of controlling the
concurrent access to data in a distributed application using the
Pessimistic Offline Lock design pattern. In our case, the application
processes a complex entity, which contains in a hierarchical structure
different other entities (objects). It will be shown how the complex
entity and the contained entities must be locked in order to control
the concurrent access to data.
Abstract: This paper describes the design and results of FROID,
an outbound intrusion detection system built with agent technology
and supported by an attacker-centric ontology. The prototype
features a misuse-based detection mechanism that identifies remote
attack tools in execution. Misuse signatures composed of attributes
selected through entropy analysis of outgoing traffic streams and
process runtime data are derived from execution variants of attack
programs. The core of the architecture is a mesh of self-contained
detection cells organized non-hierarchically that group agents in a
functional fashion. The experiments show performance gains when
the ontology is enabled as well as an increase in accuracy achieved
when correlation cells combine detection evidence received from
independent detection cells.
Abstract: Liver segmentation is the first significant process for
liver diagnosis of the Computed Tomography. It segments the liver
structure from other abdominal organs. Sophisticated filtering techniques
are indispensable for a proper segmentation. In this paper, we
employ a 3D anisotropic diffusion as a preprocessing step. While
removing image noise, this technique preserve the significant parts
of the image, typically edges, lines or other details that are important
for the interpretation of the image. The segmentation task is done
by using thresholding with automatic threshold values selection and
finally the false liver region is eliminated using 3D connected component.
The result shows that by employing the 3D anisotropic filtering,
better liver segmentation results could be achieved eventhough simple
segmentation technique is used.
Abstract: Digital watermarking is the process of embedding
information into a digital signal which can be used in DRM (digital
rights managements) system. The visible watermark (often called logo)
can indicate the owner of the copyright which can often be seen in the
TV program and protects the copyright in an active way. However,
most of the schemes do not consider the visible watermark removing
process. To solve this problem, a visible watermarking scheme with
embedding and removing process is proposed under the control of a
secure template. The template generates different version of
watermarks which can be seen visually the same for different users.
Users with the right key can completely remove the watermark and
recover the original image while the unauthorized user is prevented to
remove the watermark. Experiment results show that our
watermarking algorithm obtains a good visual quality and is hard to be
removed by the illegally users. Additionally, the authorized users can
completely remove the visible watermark and recover the original
image with a good quality.
Abstract: A great deal of research works in the field information
systems security has been based on a positivist paradigm. Applying
the reductionism concept of the positivist paradigm for information
security means missing the bigger picture and thus, the lack of holism
which could be one of the reasons why security is still overlooked,
comes as an afterthought or perceived from a purely technical
dimension. We need to reshape our thinking and attitudes towards
security especially in a complex and dynamic environment such as e-
Business to develop a holistic understanding of e-Business security in
relation to its context as well as considering all the stakeholders in
the problem area. In this paper we argue the suitability and need for
more inductive interpretive approach and qualitative research method
to investigate e-Business security. Our discussion is based on a
holistic framework of enquiry, nature of the research problem, the
underling theoretical lens and the complexity of e-Business
environment. At the end we present a research strategy for
developing a holistic framework for understanding of e-Business
security problems in the context of developing countries based on an
interdisciplinary inquiry which considers their needs and
requirements.
Abstract: The estimation of overall on-site and off-site greenhouse gas (GHG) emissions by wastewater treatment plants revealed that in anaerobic and hybrid treatment systems greater emissions result from off-site processes compared to on-site processes. However, in aerobic treatment systems, onsite processes make a higher contribution to the overall GHG emissions. The total GHG emissions were estimated to be 1.6, 3.3 and 3.8 kg CO2-e/kg BOD in the aerobic, anaerobic and hybrid treatment systems, respectively. In the aerobic treatment system without the recovery and use of the generated biogas, the off-site GHG emissions were 0.65 kg CO2-e/kg BOD, accounting for 40.2% of the overall GHG emissions. This value changed to 2.3 and 2.6 kg CO2-e/kg BOD, and accounted for 69.9% and 68.1% of the overall GHG emissions in the anaerobic and hybrid treatment systems, respectively. The increased off-site GHG emissions in the anaerobic and hybrid treatment systems are mainly due to material usage and energy demand in these systems. The anaerobic digester can contribute up to 100%, 55% and 60% of the overall energy needs of plants in the aerobic, anaerobic and hybrid treatment systems, respectively.
Abstract: Accurate timing alignment and stability is important
to maximize the true counts and minimize the random counts in
positron emission tomography So signals output from detectors must
be centering with the two isotopes to pre-operation and fed signals
into four units of pulse-processing units, each unit can accept up to
eight inputs. The dual source computed tomography consist two units
on the left for 15 detector signals of Cs-137 isotope and two units on
the right are for 15 detectors signals of Co-60 isotope. The gamma
spectrum consisting of either single or multiple photo peaks. This
allows for the use of energy discrimination electronic hardware
associated with the data acquisition system to acquire photon counts
data with a specific energy, even if poor energy resolution detectors
are used. This also helps to avoid counting of the Compton scatter
counts especially if a single discrete gamma photo peak is emitted by
the source as in the case of Cs-137. In this study the polyenergetic
version of the alternating minimization algorithm is applied to the
dual energy gamma computed tomography problem.
Abstract: Raisin Concentrate (RC) are the most important
products obtained in the raisin processing industries. These RC
products are now used to make the syrups, drinks and confectionery
productions and introduced as natural substitute for sugar in food
applications. Iran is a one of the biggest raisin exporter in the world
but unfortunately despite a good raw material, no serious effort to
extract the RC has been taken in Iran. Therefore, in this paper, we
determined and analyzed affected parameters on extracting RC
process and then optimizing these parameters for design the
extracting RC process in two types of raisin (round and long)
produced in Khorasan region. Two levels of solvent (1:1 and 2:1),
three levels of extraction temperature (60°C, 70°C and 80°C), and
three levels of concentration temperature (50°C, 60°C and 70°C)
were the treatments. Finally physicochemical characteristics of the
obtained concentrate such as color, viscosity, percentage of reduction
sugar, acidity and the microbial tests (mould and yeast) were
counted. The analysis was performed on the basis of factorial in the
form of completely randomized design (CRD) and Duncan's multiple
range test (DMRT) was used for the comparison of the means.
Statistical analysis of results showed that optimal conditions for
production of concentrate is round raisins when the solvent ratio was
2:1 with extraction temperature of 60°C and then concentration
temperature of 50°C. Round raisin is cheaper than the long one, and
it is more economical to concentrate production. Furthermore, round
raisin has more aromas and the less color degree with increasing the
temperature of concentration and extraction. Finally, according to
mentioned factors the concentrate of round raisin is recommended.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: Conventional materials like glass, wood or metals
replacement with polymer materials is still continuing. More simple
thus cheaper production is the main reason. However due to high
energy and petrochemical prices are polymer prices increasing too.
That´s why various kinds of fillers are used to make polymers
cheaper. Of course target is to maintain or improve properties of
these compounds. In this paper are solved rheology issues of
polymers compounded with vegetal origin fibers.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: This paper provides a new approach to solve the motion planning problems of flying robots in uncertain 3D dynamic environments. The robots controlled by this method can adaptively choose the fast way to avoid collision without information about the shapes and trajectories of obstacles. Based on sphere coordinates the new method accomplishes collision avoidance of flying robots without any other auxiliary positioning systems. The Self-protection System gives robots self-protection abilities to work in uncertain 3D dynamic environments. Simulations illustrate the validity of the proposed method.
Abstract: In this study, oxidative steam reforming of methanol (OSRM) over a Au/CeO2–Fe2O3 catalyst prepared by a depositionprecipitation (DP) method was studied to produce hydrogen in order to feed a Proton Exchange Membrane Fuel Cell (PEMFC). The support (CeO2, Fe2O3, and CeO2–Fe2O3) were prepared by precipitation and co-precipitation methods. The impact of the support composition on the catalytic performance was studied by varying the Ce/(Ce+Fe) atomic ratio, it was found that the 1%Au/CF(0.25) calcined at 300 °C exhibited the highest catalytic activity in the whole temperature studied. In addition, the effect of Au content was investigated and 3%Au/CF(0.25) exhibited the highest activity under the optimum condition in the temperature range of 200 °C to 400 °C. The catalysts were characterized by various techniques: XRD, TPR, XRF, and UV-vis.
Abstract: This is a genetic comparison study of Arabian Oryx
(Oryx leucoryx) population at two different locations (A &B) based
on nuclear microsatellite DNA markers. Arabian Oryx is listed as
vulnerable and endanger by the World Conservation Union (IUCN).
Thirty microsatellite markers from bovine family were applied to
investigate the genetic diversity of the Arabian Oryx and to set up a
molecular inventory. Among 30 microsatellite markers used, 13
markers were moderately polymorphic. Arabian Oryx at location A
has shown better gene diversity over location B. However, mean
number of alleles were less than location B. Data of within
population inbreeding coefficient indicates inbreeding at both
locations (A&B). Based on the analysis of polymorphic microsatellite
markers, the study revealed that Arabian Oryx need a genetically
designed breeding program.
Abstract: In this work, we present for the first time in our
perception an efficient digital watermarking scheme for mpeg audio
layer 3 files that operates directly in the compressed data domain,
while manipulating the time and subband/channel domain. In
addition, it does not need the original signal to detect the watermark.
Our scheme was implemented taking special care for the efficient
usage of the two limited resources of computer systems: time and
space. It offers to the industrial user the capability of watermark
embedding and detection in time immediately comparable to the real
music time of the original audio file that depends on the mpeg
compression, while the end user/audience does not face any artifacts
or delays hearing the watermarked audio file. Furthermore, it
overcomes the disadvantage of algorithms operating in the PCMData
domain to be vulnerable to compression/recompression attacks,
as it places the watermark in the scale factors domain and not in the
digitized sound audio data. The strength of our scheme, that allows it
to be used with success in both authentication and copyright
protection, relies on the fact that it gives to the users the enhanced
capability their ownership of the audio file not to be accomplished
simply by detecting the bit pattern that comprises the watermark
itself, but by showing that the legal owner knows a hard to compute
property of the watermark.
Abstract: Reactive powder concretes (RPC) are characterized by
particle diameter not exceeding 600 μm and having very high
compressive and tensile strengths. This paper describes a new
generation of micro concrete, which has an initial, as well as a final,
high physicomechanical performance. To achieve this, we replaced
the Portland cement (15% by weight) by materials rich in Silica (Slag
and Dune Sand).
The results obtained from tests carried out on RPC show that
compressive and tensile strengths increase when adding the additions,
thus improving the compactness of mixtures via filler and pozzolanic
effect.
With a reduction of the aggregate phase in the RPC and the
abundance of dune sand (south Algeria) and slag (industrial byproduct
of blast furnace), the use of the RPC will allow Algeria to
fulfil economical as well as ecological requirements.