Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: This paper develops an unscented grid-based filter
and a smoother for accurate nonlinear modeling and analysis
of time series. The filter uses unscented deterministic sampling
during both the time and measurement updating phases, to approximate
directly the distributions of the latent state variable. A
complementary grid smoother is also made to enable computing
of the likelihood. This helps us to formulate an expectation
maximisation algorithm for maximum likelihood estimation of
the state noise and the observation noise. Empirical investigations
show that the proposed unscented grid filter/smoother compares
favourably to other similar filters on nonlinear estimation tasks.
Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: Wireless Sensor Networks (WSN) are emerging
because of the developments in wireless communication technology and miniaturization of the hardware. WSN consists of a large number of low-cost, low-power, multifunctional sensor nodes to monitor physical conditions, such as temperature, sound, vibration, pressure,
motion, etc. The MAC protocol to be used in the sensor networks must be energy efficient and this should aim at conserving the energy during its operation. In this paper, with the focus of analyzing the
MAC protocols used in wireless Adhoc networks to WSN, simulation
experiments were conducted in Global Mobile Simulator
(GloMoSim) software. Number of packets sent by regular nodes, and received by sink node in different deployment strategies, total energy
spent, and the network life time have been chosen as the metric for comparison. From the results of simulation, it is evident that the IEEE 802.11 protocol performs better compared to CSMA and MACA protocols.
Abstract: The localized corrosion behavior of laser surface
melted 304L austenitic stainless steel was studied by
potentiodynamic polarization test. The extent of improvement in
corrosion resistance was governed by the preferred orientation and
the percentage of delta ferrite present on the surface of the laser
melted sample. It was established by orientation imaging microscopy
that the highest pitting potential value was obtained when grains were
oriented in the most close- packed [101] direction compared to the
random distribution of the base metal and other laser surface melted
samples oriented in [001] direction. The sample with lower
percentage of ferrite had good pitting resistance.
Abstract: Throughout this paper, a relatively new technique, the Tabu search variable selection model, is elaborated showing how it can be efficiently applied within the financial world whenever researchers come across the selection of a subset of variables from a whole set of descriptive variables under analysis. In the field of financial prediction, researchers often have to select a subset of variables from a larger set to solve different type of problems such as corporate bankruptcy prediction, personal bankruptcy prediction, mortgage, credit scoring and the Arbitrage Pricing Model (APM). Consequently, to demonstrate how the method operates and to illustrate its usefulness as well as its superiority compared to other commonly used methods, the Tabu search algorithm for variable selection is compared to two main alternative search procedures namely, the stepwise regression and the maximum R 2 improvement method. The Tabu search is then implemented in finance; where it attempts to predict corporate bankruptcy by selecting the most appropriate financial ratios and thus creating its own prediction score equation. In comparison to other methods, mostly the Altman Z-Score model, the Tabu search model produces a higher success rate in predicting correctly the failure of firms or the continuous running of existing entities.
Abstract: We here propose improved version of elastic graph matching (EGM) as a face detector, called the multi-scale EGM (MS-EGM). In this improvement, Gabor wavelet-based pyramid reduces computational complexity for the feature representation often used in the conventional EGM, but preserving a critical amount of information about an image. The MS-EGM gives us higher detection performance than Viola-Jones object detection algorithm of the AdaBoost Haar-like feature cascade. We also show rapid detection speeds of the MS-EGM, comparable to the Viola-Jones method. We find fruitful benefits in the MS-EGM, in terms of topological feature representation for a face.
Abstract: The proof of concept experiments were conducted to
determine the feasibility of using small amounts of Dissolved
Sulphur (DS) from the gaseous phase to precipitate platinum ions in
chloride media. Two sets of precipitation experiments were
performed in which the source of sulphur atoms was either a
thiosulphate solution (Na2S2O3) or a sulphur dioxide gas (SO2). In
liquid-liquid (L-L) system, complete precipitation of Pt was achieved
at small dosages of Na2S2O3 (0.01 – 1.0 M) in a time interval of 3-5
minutes. On the basis of this result, gas absorption tests were carried
out mainly to achieve sulphur solubility equivalent to 0.018 M. The
idea that huge amounts of precious metals could be recovered
selectively from their dilute solutions by utilizing the waste SO2
streams at low pressure seemed attractive from the economic and
environmental point of views. Therefore, mass transfer characteristics
of SO2 gas associated with reactive absorption across the gas-liquid
(G-L) interface were evaluated under different conditions of pressure
(0.5 – 2 bar), solution temperature ranges from 20 – 50 oC and acid
strength (1 – 4 M, HCl). This paper concludes with information about
selective precipitation of Pt in the presence of cations (Fe2+, Co2+,
and Cr3+) in a CSTR and recommendation to scale up laboratory data
to industrial pilot scale operations.
Abstract: The Goursat partial differential equation arises in
linear and non linear partial differential equations with mixed
derivatives. This equation is a second order hyperbolic partial
differential equation which occurs in various fields of study such as
in engineering, physics, and applied mathematics. There are many
approaches that have been suggested to approximate the solution of
the Goursat partial differential equation. However, all of the
suggested methods traditionally focused on numerical differentiation
approaches including forward and central differences in deriving the
scheme. An innovation has been done in deriving the Goursat partial
differential equation scheme which involves numerical integration
techniques. In this paper we have developed a new scheme to solve
the Goursat partial differential equation based on the Adomian
decomposition (ADM) and associated with Boole-s integration rule to
approximate the integration terms. The new scheme can easily be
applied to many linear and non linear Goursat partial differential
equations and is capable to reduce the size of computational work.
The accuracy of the results reveals the advantage of this new scheme
over existing numerical method.
Abstract: In process control applications, above 90% of the
controllers are of PID type. This paper proposed a robust PI
controller with fractional-order integrator. The PI parameters were
obtained using classical Ziegler-Nichols rules but enhanced with the
application of error filter cascaded to the fractional-order PI. The
controller was applied on steam temperature process that was
described by FOPDT transfer function. The process can be classified
as lag dominating process with very small relative dead-time. The
proposed control scheme was compared with other PI controller
tuned using Ziegler-Nichols and AMIGO rules. Other PI controller
with fractional-order integrator known as F-MIGO was also
considered. All the controllers were subjected to set point change and
load disturbance tests. The performance was measured using Integral
of Squared Error (ISE) and Integral of Control Signal (ICO). The
proposed controller produced best performance for all the tests with
the least ISE index.
Abstract: In this paper, a pipelined version of genetic algorithm,
called PLGA, and a corresponding hardware platform are described.
The basic operations of conventional GA (CGA) are made pipelined
using an appropriate selection scheme. The selection operator, used
here, is stochastic in nature and is called SA-selection. This helps
maintaining the basic generational nature of the proposed pipelined
GA (PLGA). A number of benchmark problems are used to compare
the performances of conventional roulette-wheel selection and the
SA-selection. These include unimodal and multimodal functions with
dimensionality varying from very small to very large. It is seen that
the SA-selection scheme is giving comparable performances with
respect to the classical roulette-wheel selection scheme, for all the
instances, when quality of solutions and rate of convergence are considered.
The speedups obtained by PLGA for different benchmarks
are found to be significant. It is shown that a complete hardware
pipeline can be developed using the proposed scheme, if parallel
evaluation of the fitness expression is possible. In this connection
a low-cost but very fast hardware evaluation unit is described.
Results of simulation experiments show that in a pipelined hardware
environment, PLGA will be much faster than CGA. In terms of
efficiency, PLGA is found to outperform parallel GA (PGA) also.
Abstract: The feasibility of employing solar radiation for
enhanced Fenton process in degradation of combined chlorpyrifos,
cypermethrin and chlorothalonil pesticides was examined. The effect
of various operating conditions of the process on biodegradability
improvement and mineralization of the pesticides were also
evaluated. The optimum operating conditions for treatment of
aqueous solution containing 100, 50 and 250 mg L-1 chlorpyrifos
cypermethrin and chlorothalonil, respectively were observed to be
H2O2/COD molar ratio 2, H2O2/Fe2+ molar ratio 25 and pH 3. Under
the optimum operating conditions, complete degradation of the
pesticides occurred in 1 min. Biodegradability (BOD5/COD)
increased from zero to 0.36 in 60 min, and COD and TOC removal
were 74.19 and 58.32%, respectively in 60 min. Due to
mineralization of organic carbon, decrease in ammonia-nitrogen from
22 to 4.3 mg L-1 and increase in nitrate from 0.7 to 18.1 mg L-1 in
60 min were recorded. The study indicated that solar photo-Fenton
process can be used for pretreatment of chlorpyrifos, cypermethrin
and chlorothalonil pesticides in aqueous solution for further
biological treatment.
Abstract: The characterization of κ-carrageenan could provide a
better understanding of its functions in biological, medical and
industrial applications. Chemical and physical analyses of
carrageenan from seaweeds, Euchema cottonii L., were done to offer
information on its properties and the effects of Co-60 γ-irradiation on
its thermochemical characteristics. The structural and morphological
characteristics of κ-carrageenan were determined using scanning
electron microscopy (SEM) while the composition, molecular weight
and thermal properties were determined using attenuated total
reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gel
permeation chromatography (GPC), thermal gravimetric analysis
(TGA) and differential scanning calorimetry (DSC). Further chemical
analysis was done using hydrogen-1 nuclear magnetic resonance (1H
NMR) and functional characteristics in terms of biocompatibility
were evaluated using cytotoxicity test.
Abstract: The main purpose of this paper is to research on the
methodologies of BYD to implement the opportune innovation. BYD
is a Chinese company which has the IT component manufacture, the
rechargeable battery and the automobile businesses. The paper deals
with the innovation methodology as the same as the IPR management
BYD implements in order to obtain the rapid growth of technology
development with the reasonable cost of money and time.
Abstract: In this paper the neural network-based controller is
designed for motion control of a mobile robot. This paper treats the
problems of trajectory following and posture stabilization of the
mobile robot with nonholonomic constraints. For this purpose the
recurrent neural network with one hidden layer is used. It learns
relationship between linear velocities and error positions of the
mobile robot. This neural network is trained on-line using the
backpropagation optimization algorithm with an adaptive learning
rate. The optimization algorithm is performed at each sample time to
compute the optimal control inputs. The performance of the proposed
system is investigated using a kinematic model of the mobile robot.
Abstract: As the Computed Tomography(CT) requires normally
hundreds of projections to reconstruct the image, patients are exposed
to more X-ray energy, which may cause side effects such as cancer.
Even when the variability of the particles in the object is very less,
Computed Tomography requires many projections for good quality
reconstruction. In this paper, less variability of the particles in an
object has been exploited to obtain good quality reconstruction.
Though the reconstructed image and the original image have same
projections, in general, they need not be the same. In addition
to projections, if a priori information about the image is known,
it is possible to obtain good quality reconstructed image. In this
paper, it has been shown by experimental results why conventional
algorithms fail to reconstruct from a few projections, and an efficient
polynomial time algorithm has been given to reconstruct a bi-level
image from its projections along row and column, and a known sub
image of unknown image with smoothness constraints by reducing the
reconstruction problem to integral max flow problem. This paper also
discusses the necessary and sufficient conditions for uniqueness and
extension of 2D-bi-level image reconstruction to 3D-bi-level image
reconstruction.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: Environment both endowed and built are essential for
tourism. However tourism and environment maintains a complex
relationship, where in most cases environment is at the receiving end.
Many tourism development activities have adverse environmental
effects, mainly emanating from construction of general infrastructure
and tourism facilities. These negative impacts of tourism can lead to
the destruction of precious natural resources on which it depends.
These effects vary between locations; and its effect on a hill
destination is highly critical. This study aims at developing a
Sustainable Tourism Planning Model for an environmentally
sensitive tourism destination in Kerala, India. Being part of the
Nilgiri mountain ranges, Munnar falls in the Western Ghats, one of
the biological hotspots in the world. Endowed with a unique high
altitude environment Munnar inherits highly significant ecological
wealth. Giving prime importance to the protection of this ecological
heritage, the study proposes a tourism planning model with resource
conservation and sustainability as the paramount focus. Conceiving a
novel approach towards sustainable tourism planning, the study
proposes to assess tourism attractions using Ecological Sensitivity
Index (ESI) and Tourism Attractiveness Index (TAI). Integration of
these two indices will form the Ecology – Tourism Matrix (ETM),
outlining the base for tourism planning in an environmentally
sensitive destination. The ETM Matrix leads to a classification of
tourism nodes according to its Conservation Significance and
Tourism Significance. The spatial integration of such nodes based on
the Hub & Spoke Principle constitutes sub – regions within the STZ.
Ensuing analyses lead to specific guidelines for the STZ as a whole,
specific tourism nodes, hubs and sub-regions. The study results in a
multi – dimensional output, viz., (1) Classification system for tourism
nodes in an environmentally sensitive region/ destination (2)
Conservation / Tourism Development Strategies and Guidelines for
the micro and macro regions and (3) A Sustainable Tourism Planning
Tool particularly for Ecologically Sensitive Destinations, which can
be adapted for other destinations as well.
Abstract: Modeling product configurations needs large amounts of knowledge about technical and marketing restrictions on the product. Previous attempts to automate product configurations concentrate on representations and management of the knowledge for specific domains in fixed and isolated computing environments. Since the knowledge about product configurations is subject to continuous change and hard to express, these attempts often failed to efficiently manage and exchange the knowledge in collaborative product development. In this paper, XML Topic Map (XTM) is introduced to represent and exchange the knowledge about product configurations in collaborative product development. A product configuration model based on XTM along with its merger and inference facilities enables configuration engineers in collaborative product development to manage and exchange their knowledge efficiently. A prototype implementation is also presented to demonstrate the proposed model can be applied to engineering information systems to exchange the product configuration knowledge.
Abstract: Discrete particle swarm optimization (DPSO) is a
powerful stochastic evolutionary algorithm that is used to solve the
large-scale, discrete and nonlinear optimization problems. However,
it has been observed that standard DPSO algorithm has premature
convergence when solving a complex optimization problem like
transmission expansion planning (TEP). To resolve this problem an
advanced discrete particle swarm optimization (ADPSO) is proposed
in this paper. The simulation result shows that optimization of lines
loading in transmission expansion planning with ADPSO is better
than DPSO from precision view point.