Abstract: We investigate experimentally and theoretically the
dynamics of a capacitive resonator under mixed frequency excitation
of two AC harmonic signals. The resonator is composed of a proof
mass suspended by two cantilever beams. Experimental
measurements are conducted using a laser Doppler Vibrometer to
reveal the interesting dynamics of the system when subjected to twosource
excitation. A nonlinear single-degree-of-freedom model is
used for the theoretical investigation. The results reveal combination
resonances of additive and subtractive type, which are shown to be
promising to increase the bandwidth of the resonator near primary
resonance frequency. Our results also demonstrate the ability to shift
the combination resonances to much lower or much higher frequency
ranges. We also demonstrate the dynamic pull-in instability under
mixed frequency excitation.
Abstract: Experimental economics is subject to criticism with
regards to frequently discussed the trade-off between internal and
external validity requirements, which seems to be critically flawed.
This paper evaluates incompatibility of trade-off condition and
condition of internal validity as a prerequisite for external validity. In
addition, it outlines the imprecise concept of artificiality, which is
found to be rather improving the external validity and seems to
strengthen the illusory status of external versus internal validity
tension. Internal validity is further analyzed with regards to Duhem-
Quine problem, where unpredictability argument is significantly
weakened trough application of inductivism within the illustrative
hypothetical-deductive model. Our discussion partially weakens
critical arguments related to the robustness of results in experimental
economics, if the perfectly controlled experimental environment is
secured.
Abstract: In this study, the experiments were carried out to
determine the best coolant for the quenching process among waterbased
silica, alumina, titania and copper oxide nanofluids (0.1 vol%).
A sphere made up off brass material was used in the experiments.
When the spherical test specimen was heated at high temperatures, it
was suddenly immersed into the nanofluids. All experiments were
carried out at saturated conditions and under atmospheric pressure.
After the experiments, the cooling curves were obtained by using the
temperature-time data of the specimen. The experimental results
showed that the cooling performance of test specimen depended on
the type of nanofluids. The silica nanoparticles enhanced the
performance of boiling heat transfer and it is the best coolant for the
quenching among other nanoparticles.
Abstract: There is not much effective guideline on development of design parameters selection on spring back for advanced high strength steel sheet metal in U-channel process during cold forming process. This paper presents the development of predictive model for spring back in U-channel process on advanced high strength steel sheet employing Response Surface Methodology (RSM). The experimental was performed on dual phase steel sheet, DP590 in Uchannel forming process while design of experiment (DoE) approach was used to investigates the effects of four factors namely blank holder force (BHF), clearance (C) and punch travel (Tp) and rolling direction (R) were used as input parameters using two level values by applying Full Factorial design (24 ). From a statistical analysis of variant (ANOVA), result showed that blank holder force (BHF), clearance (C) and punch travel (Tp) displayed significant effect on spring back of flange angle (β2 ) and wall opening angle (β1 ), while rolling direction (R) factor is insignificant. The significant parameters are optimized in order to reduce the spring back behavior using Central Composite Design (CCD) in RSM and the optimum parameters were determined. A regression model for spring back was developed. The effect of individual parameters and their response was also evaluated. The results obtained from optimum model are in agreement with the experimental values.
Abstract: The present study is concerned with the problem of determining the shape of the free surface flow in a hydraulic channel which has an uneven bottom. For the mathematical formulation of the problem, the fluid of the two-dimensional irrotational steady flow in water is assumed inviscid and incompressible. The solutions of the nonlinear problem are obtained by using the usual conformal mapping theory and Hilbert’s technique. An experimental study, for comparing the obtained results, has been conducted in a hydraulic channel (subcritical regime and supercritical regime).
Abstract: In the immunologic sense, clinical infection is a state
of failure of the immune system to combat the pathogenic weapon of
the bacteria invading the host. A motile gram negative vibroid
organism associated with marked mono and poly nuclear cell
responses was traced during the examination of a clinical material
from an infected common carp Cyprinus carpio. On primary plate
culture, growth was shown to be pure, dense population of an
Aeromonas-like colony morphotype. The pure isolate was found to
be; Aerobic, facultatively anaerobic, non-halophilic, grew at 0C, and
37C, oxidase positive utilizes glucose through fermentative pathway,
resist 0/129 and novobiocin, produces alanine and lysine
decarboxylases but non-producing ornithine dehydrolases. Tests for
the in vitro determinants of pathogenicity has shown to be; Betahaemolytic
onto blood agar, gelatinase, casienase and amylase
producer. Three in vivo determinants of pathogenicity were tested as,
the lethal dose fifty, the pathogenesis and pathogenicity. It was
evident that 0.1 milliliter of the causal bacterial cell suspension of a
density 1 x 107 CFU/ml injected intramuscularly into an average of
100gms fish toke five days incubation period, then at the day six
morbidity and mortality were initiated. LD50 was recorded at the day
12 post-infection. Use of an LD50 doses to study the pathogenicity,
reveals mononuclear and polynuclear cell responses, on examining
the stained direct films of the clinical materials from the
experimentally infected fish. Re-isolation tests confirm that the reisolant
is same. The course of the infection in natural case was shown
manifestation of; skin ulceration, haemorrhage and descaling. On
evisceration, the internal organs were shown; congestion in the
intestines, spleen and, air sacs. The induced infection showed a
milder form of these manifestations. The grading of the virulence of
this organism was virulent causing chronic course of infections as
indicated from the pathogenesis and pathogenicity studies. Thus the
infectious bacteria were consistent with Aeromonas hydrophila, and
the infection was chronic.
Abstract: Biomass briquette gasification is regarded as a
promising route for efficient briquette use in energy generation, fuels
and other useful chemicals. However, previous research has been
focused on briquette gasification in fixed bed gasifiers such as
updraft and downdraft gasifiers. Fluidised bed gasifier has the
potential to be effectively sized to medium or large scale. This study
investigated the use of fuel briquettes produced from blends of rice
husks and corn cobs biomass, in a bubbling fluidised bed gasifier.
The study adopted a combination of numerical equations and Aspen
Plus simulation software, to predict the product gas (syngas)
composition base on briquette density and biomass composition
(blend ratio of rice husks to corn cobs). The Aspen Plus model was
based on an experimentally validated model from the literature. The
results based on a briquette size 32 mm diameter and relaxed density
range of 500 to 650kg/m3, indicated that fluidisation air required in
the gasifier increased with increase in briquette density, and the
fluidisation air showed to be the controlling factor compared with the
actual air required for gasification of the biomass briquettes. The
mass flowrate of CO2 in the predicted syngas composition increased
with an increase in air flow, in the gasifier, while CO decreased and
H2 was almost constant. The ratio of H2 to CO for various blends of
rice husks and corn cobs did not significantly change at the designed
process air, but a significant difference of 1.0 was observed between
10/90 and 90/10 % blend of rice husks and corn cobs.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Nowadays, the rapid development of CAD systems’
programming environments results in the creation of multiple
downstream applications, which are developed and becoming
increasingly available. CAD based manufacturing simulations is
gradually following the same trend. Drilling is the most popular holemaking
process used in a variety of industries. A specially built piece
of software that deals with the drilling kinematics is presented. The
cutting forces are calculated based on the tool geometry, the cutting
conditions and the tool/work-piece materials. The results are verified
by experimental work. Finally, the response surface methodology
(RSM) is applied and mathematical models of the total thrust force
and the thrust force developed because of the main cutting edges are
proposed.
Abstract: This study is aiming at establishing the relationship
between the optical signal of flame and an equivalent ratio of flame. In
this experiment, flame optical signal in a furnace is measured using
photodiode. The combustion system is composed of metal fiber burner
and vertical furnace, and flame chemiluminescence is measured at
various experimental conditions. In this study, the flame
chemiluminescence of laminar premixed flame is measured using
commercially available photodiode. It is experimentally investigated
the relationship between equivalent ratio and photodiode signal. In
addition, the strategy of combustion control method is proposed using
the optical signal and fuel pressure.
The results showed that certain relationship between optical data of
photodiode and equivalence ratio exists, and this leads to the
successful application of this system for instantaneous measurement of
equivalence ration of the combustion system.
Abstract: Steady three-dimensional and two free surface waves
generated by moving bodies are presented, the flow problem to be
simulated is rich in complexity and poses many modeling challenges
because of the existence of breaking waves around the ship hull, and
because of the interaction of the two-phase flow with the turbulent
boundary layer. The results of several simulations are reported. The
first study was performed for NACA0012 of hydrofoil with different
meshes, this section is analyzed at h/c= 1, 0345 for 2D. In the second
simulation a mathematically defined Wigley hull form is used to
investigate the application of a commercial CFD code in prediction of
the total resistance and its components from tangential and normal
forces on the hull wetted surface. The computed resistance and wave
profiles are used to estimate the coefficient of the total resistance for
Wigley hull advancing in calm water under steady conditions. The
commercial CFD software FLUENT version 12 is used for the
computations in the present study. The calculated grid is established
using the code computer GAMBIT 2.3.26. The shear stress k-ωSST
model is used for turbulence modeling and the volume of fluid
technique is employed to simulate the free-surface motion. The
second order upwind scheme is used for discretizing the convection
terms in the momentum transport equations, the Modified HRIC
scheme for VOF discretization. The results obtained compare well
with the experimental data.
Abstract: Nowadays, the main goal for modern horticultural
production is an increase the quality. In recent years, the use of
organic fertilizers or biostimulants that can be applied in agriculture
to improve quali-quantitative crop yields has encountered increasing
interest. Biostimulants are gaining importance also for their possible
use in organic and sustainable agriculture, to avoid excessive
fertilizer applications. Consecutive experimental trials were carried
out in the Apulia region (southern Italy) on three herbaceous crops
(cauliflower, pepper, fennel) grown in pots under conventional and
organic fertilization systems without and with biostimulants. The aim
was to determine the effects of three biostimulants (Siapton®10L,
Micotech L, Lysodin Alga-Fert) on quali-quantitative yield
characteristics. At harvest, the quali-quantitative yield characteristics
of each crop were determined. All of the experimental data were
subjected to analysis of variance (ANOVA), and when significant
effects were detected, the means were compared using Tukey’s tests.
These data show large differences in these yield characteristics
between conventional and organic crops, particularly highlighting
higher yields for the conventional crops, while variable results were
generally observed when the biostimulants were applied. In this
context, there were no effects of the biostimulants on the quantitative
yield, whereas there were low positive effects on the qualitative
characteristics, as related to higher dry matter content of cauliflower,
and higher soluble solids content of pepper. Moreover, there were
evident positive effects of the biostimulants with fennel, due to the
lower nitrate content. These latter data are in line with most of the
published literature obtained for other herbaceous crops.
Abstract: Fast speed drives for Permanent Magnet Synchronous
Motor (PMSM) is a crucial performance for the electric traction
systems. In this paper, PMSM is derived with a Model-based
Predictive Control (MPC) technique. Fast speed tracking is achieved
through optimization of the DC source utilization using MPC. The
technique is based on predicting the optimum voltage vector applied
to the driver. Control technique is investigated by comparing to the
cascaded PI control based on Space Vector Pulse Width Modulation
(SVPWM). MPC and SVPWM-based FOC are implemented with the
TMS320F2812 DSP and its power driver circuits. The designed MPC
for a PMSM drive is experimentally validated on a laboratory test
bench. The performances are compared with those obtained by a
conventional PI-based system in order to highlight the improvements,
especially regarding speed tracking response.
Abstract: The nanoindentation behaviour and phase
transformation of annealed single-crystal silicon wafers are examined.
The silicon specimens are annealed at temperatures of 250, 350 and
450ºC, respectively, for 15 minutes and are then indented to maximum
loads of 30, 50 and 70 mN. The phase changes induced in the indented
specimens are observed using transmission electron microscopy
(TEM) and micro-Raman scattering spectroscopy (RSS). For all
annealing temperatures, an elbow feature is observed in the unloading
curve following indentation to a maximum load of 30 mN. Under
higher loads of 50 mN and 70 mN, respectively, the elbow feature is
replaced by a pop-out event. The elbow feature reveals a complete
amorphous phase transformation within the indented zone, whereas
the pop-out event indicates the formation of Si XII and Si III phases.
The experimental results show that the formation of these crystalline
silicon phases increases with an increasing annealing temperature and
indentation load. The hardness and Young’s modulus both decrease as
the annealing temperature and indentation load are increased.
Abstract: Current research is targeting new molecular
mechanisms that underlie non-alcoholic fatty liver disease (NAFLD)
and associated metabolic disorders like non-alcoholic steatohepatitis
(NASH). Forty New Zealand White rabbits have been used and fed a
high protein (HP) and energy diet based on grains and containing
11.76 MJ/kg. Boron added to 3 experimental groups’ drinking waters
(30 mg boron/L) as boron compounds. Biochemical analysis
including boron levels, and nuclear magnetic resonance (NMR) based
metabolomics evaluation, and mRNA expression of peroxisome
proliferator-activated receptor (PPAR) family was performed. LDLcholesterol
concentrations alone were decreased in all the
experimental groups. Boron levels in serum and feces were increased.
Content of acetate was in about 2x higher for anhydrous borax group,
at least 3x higher for boric acid group. PPARα mRNA expression
was significantly decreased in boric acid group. Anhydrous borax
attenuated mRNA levels of PPARγ, which was further suppressed by
boric acid. Boron supplementation decreased the degenerative
alterations in hepatocytes. Except borax group other boron groups did
not have a pronounced change in tubular epithels of kidney. In
conclusion, high protein and energy diet leads hepatocytes’
degenerative changes which can be prevented by boron
supplementation. Boric acid seems to be more effective in this
situation.
Abstract: In the past decade, the use of digital image correlation
(DIC) techniques has increased significantly in the area of
experimental mechanics, especially for materials behavior
characterization. This non-contact tool enables full field displacement
and strain measurements over a complete region of interest. The DIC
algorithm requires a random contrast pattern on the surface of the
specimen in order to perform properly. To create this pattern, the
specimen is usually first coated using a white matt paint. Next, a
black random speckle pattern is applied using any suitable method. If
the applied paint coating is too thick, its top surface may not be able
to exactly follow the deformation of the specimen, and consequently,
the strain measurement might be underestimated. In the present
article, a study of the influence of the paint thickness on the strain
underestimation is performed for different strain levels. The results
are then compared to typical paint coating thicknesses applied by
experienced DIC users. A slight strain underestimation was observed
for paint coatings thicker than about 30μm. On the other hand, this
value was found to be uncommonly high compared to coating
thicknesses applied by DIC users.
Abstract: In the present research work we present the optical
emission studies of the Indium (In) – Tin (Sn) plasma produced by
the first (1064 nm) harmonic of an Nd: YAG nanosecond pulsed
laser. The experimentally observed line profiles of neutral Indium (In
I) and Tin (SnI) are used to extract the electron temperature (Te)
using the Boltzmann plot method. Whereas, the electron number
density (Ne) has been determined from the Stark broadening line
profile method. The Te is calculated by varying the distance from the
target surface along the line of propagation of plasma plume and also
by varying the laser irradiance. Beside we have studied the variation
of Ne as a function of laser irradiance as well as its variation with
distance from the target surface.
Abstract: Atmospheric carbon dioxide emissions are considered
as the greatest environmental challenge the world is facing today.
The tasks to control the emissions include the recovery of CO2 from
flue gas. This concern has been improved due to recent advances in
materials process engineering resulting in the development of
inorganic gas separation membranes with excellent thermal and
mechanical stability required for most gas separations. This paper,
therefore, evaluates the performance of a highly selective inorganic
membrane for CO2 recovery applications. Analysis of results
obtained is in agreement with experimental literature data. Further
results show the prediction performance of the membranes for gas
separation and the future direction of research. The materials
selection and the membrane preparation techniques are discussed.
Method of improving the interface defects in the membrane and its
effect on the separation performance has also been reviewed and in
addition advances to totally exploit the potential usage of this
innovative membrane.
Abstract: Mammography is widely used technique for breast cancer
screening. There are various other techniques for breast cancer screening
but mammography is the most reliable and effective technique. The
images obtained through mammography are of low contrast which
causes problem for the radiologists to interpret. Hence, a high quality
image is mandatory for the processing of the image for extracting any
kind of information from it. Many contrast enhancement algorithms have
been developed over the years. In the present work, an efficient
morphology based technique is proposed for contrast enhancement of
masses in mammographic images. The proposed method is based on
Multiscale Morphology and it takes into consideration the scale of the
structuring element. The proposed method is compared with other stateof-
the-art techniques. The experimental results show that the proposed
method is better both qualitatively and quantitatively than the other
standard contrast enhancement techniques.
Abstract: Pneumatic reactors have been widely employed in various sectors of the chemical industry, especially where are required high heat and mass transfer rates. This study aimed to obtain correlations that allow the prediction of gas hold-up (Ԑ) and volumetric oxygen transfer coefficient (kLa), and compare these values, for three models of pneumatic reactors on two scales utilizing Newtonian fluids. Values of kLa were obtained using the dynamic pressure-step method, while e was used for a new proposed measure. Comparing the three models of reactors studied, it was observed that the mass transfer was superior to draft-tube airlift, reaching e of 0.173 and kLa of 0.00904s-1. All correlations showed good fit to the experimental data (R2≥94%), and comparisons with correlations from the literature demonstrate the need for further similar studies due to shortage of data available, mainly for airlift reactors and high viscosity fluids.