Abstract: Laser beam welding of dissimilar sheet metal
combinations such as Ti/Al, SS/Al and Cu/Al are increasingly
demanded due to high energy densities with less fusion and heat
affected zones. A good weld joint strength involves combinations of
dissimilar metals and the formation of solid solution in the weld pool.
Many metal pairs suffer from significant intermetallic phase
formation during welding which greatly reduces their strength. The
three different sheet metal mentioned above is critically reviewed and
phase diagram for the combinations are given. The aim of this study
is to develop an efficient metal combinations and the influence on
their interfacial characteristics. For that the following parameters
such as weld geometry, residual distortion, micro hardness,
microstructure and mechanical properties are analyzed
systematically.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: Complexation of anthocyanins to mimic natural
copigmentation process was investigated. Cyanidin-rich extracts from
Zea mays L. ceritina Kulesh. and delphinidin-rich extracts from
Clitoria ternatea L. were used to form 4 anthocyanin complexes,
AC1, AC2, AC3 and AC4, in the presence of several polyphenols and
a trace metal. Characterizations of the ACs were conducted by UV,
FTIR, DSC/TGA and morphological observations. Bathochromic
shifts of the UV spectra of 4 formulas of ACs were observed at peak
wavelengths of about 510-620 nm by 10 nm suggesting complex
formation. FTIR spectra of the ACs indicate shifts of peaks from
1,733 cm-1 to 1,696 cm-1 indicating interactions and a decrease in the
peak areas within the wavenumber of 3,400-3,500 cm-1 indicating
changes in hydrogen bonding. Thermal analysis of all of the ACs
suggests increases in melting temperature after complexation. AC
with the highest melting temperature was morphologically observed
by SEM and TEM to be crystal-like particles within a range of 50 to
200 nm. Particle size analysis of the AC by laser diffraction gave a
range of 50-600 nm, indicating aggregation. This AC was shown to
have no cytotoxic effect on cultured HGEPp0.5 and HGF (all p>
0.05) by MTT. Therefore, complexation of anthocyanins was simple
and self-assembly process, potentially resulting in nanosized particles
of anthocyanin complex.
Abstract: Anthocyanins are natural pigments with effective UV
protection but their topical use could be limited due to their
physicochemical characteristics. An attempt to overcome such
limitations by complexation of 2 major anthocyanin-rich sources, C.
ternatea and Z. mays, has potentiated its use as topical antiinflammatory.
Cell studies indicate no cytotoxicity of the
anthocyanin complex (AC) up to 1 mg/ml tested in HaCaT and
human fore head fibroblasts by MTT. Croton oil-induced ear edema
in Wistar rats suggests an effective dose of 5 mg/cm2 of AC as a
topical anti-inflammatory in comparison to 0.5 mg/cm2 of
fluocinolone acetonide. Niosomal encapsulation of the AC
significantly prolonged the anti-inflammatory activity particularly at
8 h after topical application (p = 0.0001). The AC was not cytotoxic
and its anti-inflammatory and activity was dose-dependent and
prolonged by niosomal encapsulation. It has also shown to promote
collagen type 1 production in cell culture. Thus, AC could be a
potential candidate for topical anti-inflammatory agent from natural
resources.
Abstract: Content-based image retrieval (CBIR) uses the
contents of images to characterize and contact the images. This paper
focus on retrieving the image by separating images into its three color
mechanism R, G and B and for that Discrete Wavelet Transformation
is applied. Then Wavelet based Generalized Gaussian Density (GGD)
is practical which is used for modeling the coefficients from the
wavelet transforms. After that it is agreed to Histogram of Oriented
Gradient (HOG) for extracting its characteristic vectors with Relevant
Feedback technique is used. The performance of this approach is
calculated by exactness and it confirms that this method is wellorganized
for image retrieval.
Abstract: Chemical Reaction Optimization (CRO) is an
optimization metaheuristic inspired by the nature of chemical
reactions as a natural process of transforming the substances from
unstable to stable states. Starting with some unstable molecules with
excessive energy, a sequence of interactions takes the set to a state of
minimum energy. Researchers reported successful application of the
algorithm in solving some engineering problems, like the quadratic
assignment problem, with superior performance when compared with
other optimization algorithms. We adapted this optimization
algorithm to the Printed Circuit Board Drilling Problem (PCBDP)
towards reducing the drilling time and hence improving the PCB
manufacturing throughput. Although the PCBDP can be viewed as
instance of the popular Traveling Salesman Problem (TSP), it has
some characteristics that would require special attention to the
transactions that explore the solution landscape. Experimental test
results using the standard CROToolBox are not promising for
practically sized problems, while it could find optimal solutions for
artificial problems and small benchmarks as a proof of concept.
Abstract: A Silver (Ag) thin film is introduced as a template and
doping source for vertically aligned p–type ZnO nanorods. ZnO
nanorods were grown using an ammonium hydroxide based
hydrothermal process. During the hydrothermal process, the Ag thin
film was dissolved to generate Ag ions in the solution. The Ag ions can
contribute to doping in the wurzite structure of ZnO and the (111)
grain of Ag thin film can be the epitaxial temporal template for the
(0001) plane of ZnO. Hence, Ag–doped p–type ZnO nanorods were
successfully grown on the substrate, which can be an electrode or
semiconductor for the device application. To demonstrate the
potentials of this idea, p–n diode was fabricated and its electrical
characteristics were demonstrated.
Abstract: In this paper, the transient device performance analysis
of n-type Gate Inside JunctionLess Transistor (GI-JLT) has been
evaluated. 3-D Bohm Quantum Potential (BQP) transport device
simulation has been used to evaluate the delay and power dissipation
performance. GI-JLT has a number of desirable device parameters
such as reduced propagation delay, dynamic power dissipation,
power and delay product, intrinsic gate delay and energy delay
product as compared to Gate-all-around transistors GAA-JLT. In
addition to this, various other device performance parameters namely,
on/off current ratio, short channel effects (SCE), transconductance
Generation Factor (TGF) and unity gain cut-off frequency (fT ) and
subthreshold slope (SS) of the GI-JLT and GAA-JLT have been
analyzed and compared. GI-JLT shows better device performance
characteristics than GAA-JLT for low power and high frequency
applications, because of its larger gate electrostatic control on the
device operation.
Abstract: In this paper cognitive radio is presented and the
spectrum overlay cognitive radio antenna system is detailed. A UWB
antenna with frequency reconfigurable characteristics is proposed.
The reconfigurability is achieved when the filter is integrated to the
feeding line of the single port overlay cognitive radio. When
activated, the filter can transform the UWB frequency response into a
reconfigurable narrowband one, which is suitable for the
communication operation of the CR system. Here single port overlay
cognitive radio antenna is designed and simulated using Ansoft High
Frequency Structure Simulator (HFSS).
Abstract: This paper presents the scaling laws that provide the
criteria of geometry and dynamic similitude between the full-size
rotor-shaft system and its scale model, and can be used to predict the
torsional vibration characteristics of the full-size rotor-shaft system by
manipulating the corresponding data of its scale model. The scaling
factors, which play fundamental roles in predicting the geometry and
dynamic relationships between the full-size rotor-shaft system and its
scale model, for torsional free vibration problems between scale and
full-size rotor-shaft systems are firstly obtained from the equation of
motion of torsional free vibration. Then, the scaling factor of external
force (i.e., torque) required for the torsional forced vibration problems
is determined based on the Newton’s second law. Numerical results
show that the torsional free and forced vibration characteristics of a
full-size rotor-shaft system can be accurately predicted from those of
its scale models by using the foregoing scaling factors. For this reason,
it is believed that the presented approach will be significant for
investigating the relevant phenomenon in the scale model tests.
Abstract: This paper proposed a silicon controller rectifier (SCR)
based ESD protection device to protect low voltage ESD for integrated
circuit. The proposed ESD protection device has low trigger voltage
and high holding voltage compared with conventional SCR-based
ESD protection devices. The proposed ESD protection circuit is
verified and compared by TCAD simulation. This paper verified
effective low voltage ESD characteristics with low trigger voltage of
5.79V and high holding voltage of 3.5V through optimization
depending on design variables (D1, D2, D3 and D4).
Abstract: Food as perishable goods represents a specific and
sensitive part in the supply chain theory, since changing physical or
chemical characteristics considerably influence the approach to stock
management. The most delicate phase of this process is
transportation, where it becomes difficult to ensure the stable
conditions which limit deterioration, since the value of the
deterioration rate could be easily influenced by the mode of
transportation. The fuzzy definition of variables allows one to take
these variations into account. Furthermore, an appropriate choice of
the defuzzification method permits one to adapt results to real
conditions as far as possible. In this article those methods which take
into account the relationship between the deterioration rate of
perishable goods and transportation by ship will be applied with the
aim of (a) minimizing the total cost function, defined as the sum of
the ordering cost, holding cost, disposing cost and transportation
costs, and (b) improving the supply chain sustainability by reducing
environmental impact and waste disposal costs.
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: In the present study, mixed convection in a horizontal
rectangular duct using Al2O3 is numerically investigated. The effects
of different Rayleigh number, Reynolds number and radiation on
flow and heat transfer characteristics are studied in detail. This study
covers Rayleigh number in the range of 2 × 10^6 ≤ Ra ≤ 2 × 10^7 and
Reynolds number in the range of 100 ≤ Re ≤ 1100. Results reveal that
the Nusselt number increases as Reynolds and Rayleigh numbers
increase. It is also found that the dimensionless temperature
distribution increases as Rayleigh number increases.
Abstract: Carbon fiber reinforced polymersarewidely used to strengthen steel structural elements. These structural elements are normally subjected to static, dynamic and fatigue loadings during their life-time. CFRP laminate is commonly used to strengthen these structures under the subjected loads. A number of studies have focused on the characteristics of CFRP sheets bonded to steel members under static, dynamic and fatigue loadings. However, there is a gap in understanding the bonding behavior between CFRP laminates and steel members under impact loading. This paper shows the effect of high load rates on this bond. CFRP laminate CFK 150/2000 was used to strengthen steel joints using Araldite 420 epoxy. The results show that applying a high load rate significantly affects the bond strength but has little influence on the effective bond length.
Abstract: The thermal conductivity of a fluid can be
significantly enhanced by dispersing nano-sized particles in it, and
the resultant fluid is termed as "nanofluid". A theoretical model for
estimating the thermal conductivity of a nanofluid has been proposed
here. It is based on the mechanism that evenly dispersed
nanoparticles within a nanofluid undergo Brownian motion in course
of which the nanoparticles repeatedly collide with the heat source.
During each collision a rapid heat transfer occurs owing to the solidsolid
contact. Molecular dynamics (MD) simulation of the collision
of nanoparticles with the heat source has shown that there is a pulselike
pick up of heat by the nanoparticles within 20-100 ps, the extent
of which depends not only on thermal conductivity of the
nanoparticles, but also on the elastic and other physical properties of
the nanoparticle. After the collision the nanoparticles undergo
Brownian motion in the base fluid and release the excess heat to the
surrounding base fluid within 2-10 ms. The Brownian motion and
associated temperature variation of the nanoparticles have been
modeled by stochastic analysis. Repeated occurrence of these events
by the suspended nanoparticles significantly contributes to the
characteristic thermal conductivity of the nanofluids, which has been
estimated by the present model for a ethylene glycol based nanofluid
containing Cu-nanoparticles of size ranging from 8 to 20 nm, with
Gaussian size distribution. The prediction of the present model has
shown a reasonable agreement with the experimental data available
in literature.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.
Abstract: This paper presents nonlinear pulse propagation characteristics for different input optical pulse shapes with various input pulse energy levels in semiconductor optical amplifiers. For simulation of nonlinear pulse propagation, finite-difference beam propagation method is used to solve the nonlinear Schrödinger equation. In this equation, gain spectrum dynamics, gain saturation are taken into account which depends on carrier depletion, carrier heating, spectral-hole burning, group velocity dispersion, self-phase modulation and two photon absorption. From this analysis, we obtained the output waveforms and spectra for different input pulse shapes as well as for different input energies. It shows clearly that the peak position of the output waveforms are shifted toward the leading edge which due to the gain saturation of the SOA for higher input pulse energies. We also analyzed and compared the normalized difference of full-width at half maximum for different input pulse shapes in the SOA.
Abstract: The paper involves a chain of activities from
synthesis, establishment of the methodology for characterization and
testing of novel protective materials through the pilot production and
application on model supports.
It summarizes the results regarding the development of the pilot
production protocol for newly developed self-cleaning materials. The
optimization of the production parameters was completed in order to
improve the most important functional properties (mineralogy
characteristics, particle size, self-cleaning properties and
photocatalytic activity) of the newly designed nanocomposite
material.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal from environmental
pollutants. A total of 180 Male scalp hair samples were collected
from different environments in Greater Cairo (GC), i.e. industrial,
heavy traffic and rural areas (60 samples from each) having different
activities during the period of, 1/5/2010 to 1/11/2012. Hair samples
were collected during five stages. Data proved that the concentration
of lead in male industrial areas of Cairo ranged between 6.2847 to
19.0432 μg/g, with mean value of 12.3288 μg/g. On the other hand,
lead content of hair samples of residential-traffic areas ranged
between 2.8634 to 16.3311 μg/g with mean value of 9.7552 μg/g.
While lead concentration on the hair of the male residents living in
rural area ranged between 1.0499-9.0402μg/g with mean value of
4.7327 μg/g. The Pb concentration in scalp hair of Cairo residents of
residential-traffic and rural traffic areas was observed to follow the
same pattern. The pattern was that of decrease concentration of
summer and its increase in winter. Then, there was a marked increase
in Pb concentration of summer 2012, and this increase was
significant. These were obviously seen for the residential-traffic and
rural areas residents. Pb pollution in residents of industrial areas
showed the same seasonal pattern, but there was marked to decrease
in Pb concentration of summer 2012, and this decrease was
significant. Lead pollution in residents of GC was serious. It is worth
noting that the atmosphere is still contaminated by lead despite a
decade of using unleaded gasoline. Strong seasonal variation in
higher Pb concentration on winter than in summer was found. Major
contributions to the pollution with Pb could include industry
emissions, motor vehicle emissions and long transported dust from
outside Cairo. More attention should be paid to the reduction of Pb
content of the urban aerosol and to the Pb pollution health.