Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Many single or multispan arch bridges are
strengthened with the addition of some kind of structural support
between adjacent arches of multispan or beside the arch barrel of a
single span to increase the strength of the overall structure. It was
traditionally formed by either placing loose rubble masonry blocks
between the arches and beside the arches or using mortar or concrete
to construct a more substantial structural bond between the spans. On
the other hand backing materials are present in some existing bridges.
Existing arch assessment procedures generally ignore the effects of
backing materials. In this paper an investigation of the effects of
backing on ratings for masonry arch bridges is carried out. It is
observed that increasing the overall lateral stability of the arch
system through the inclusion of structural backing results in an
enhanced failure load by reducing the likelihood of any tension
occurring at the top of the arch.
Abstract: Following the research in the Department of environmental engineering in Faculty of mechanical engineering on Technical University of Kosice and experiences with electrocoagulation style of disposal waste water, there were designed and partly examining the equipment of two stage revitalization on the standing and little fusible water of tenet electrolysis on the little tarns. With the cooperation with vet experts was that manners prove and it is innocuous for animals, during which time cyanobacteria are totally paralyzed. For the implementation of science and research results have been obtained by means EU funds for structural development.
Abstract: Using efficient classification methods is necessary for automatic fingerprint recognition system. This paper introduces a new structural approach to fingerprint classification by using the directional image of fingerprints to increase the number of subclasses. In this method, the directional image of fingerprints is segmented into regions consisting of pixels with the same direction. Afterwards the relational graph to the segmented image is constructed and according to it, the super graph including prominent information of this graph is formed. Ultimately we apply a matching technique to compare obtained graph with the model graphs in order to classify fingerprints by using cost function. Increasing the number of subclasses with acceptable accuracy in classification and faster processing in fingerprints recognition, makes this system superior.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: Earthquakes produce some of the most violent loading
situations that a structure can be subjected to and if a structure fails
under these loads then inevitably human life is put at risk. One of the
most common methods by which a structure fails under seismic
loading is at the connection of structural elements. The research
presented in this paper investigates the interlock systems as a novel
method for building structures. The main objective of this
experimental study wasto determine the dynamic characteristics and
the seismic behaviour of the proposed structures compared to
conventional structural systemsduring seismic motions. Results of
this study indicate that the interlock mechanism of the panels
influences the behaviour of lateral load-resisting systems of the
structures during earthquakes, contributing to better structural
flexibility and easier maintenance.
Abstract: In this paper, we focus on the fusion of images from
different sources using multiresolution wavelet transforms. Based on
reviews of popular image fusion techniques used in data analysis,
different pixel and energy based methods are experimented. A novel
architecture with a hybrid algorithm is proposed which applies pixel
based maximum selection rule to low frequency approximations and
filter mask based fusion to high frequency details of wavelet
decomposition. The key feature of hybrid architecture is the
combination of advantages of pixel and region based fusion in a
single image which can help the development of sophisticated
algorithms enhancing the edges and structural details. A Graphical
User Interface is developed for image fusion to make the research
outcomes available to the end user. To utilize GUI capabilities for
medical, industrial and commercial activities without MATLAB
installation, a standalone executable application is also developed
using Matlab Compiler Runtime.
Abstract: Silver nanoparticles were prepared by chemical reduction method. Silver nitrate was taken as the metal precursor and hydrazine hydrate as a reducing agent. The formation of the silver nanoparticles was monitored using UV-Vis absorption spectroscopy. The UV-Vis spectroscopy revealed the formation of silver nanopart├¡cles by exhibing the typical surface plasmon absorption maxima at 418-420 nm from the UV–Vis spectrum. Comparison of theoretical (Mie light scattering theory) and experimental results showed that diameter of silver nanoparticles in colloidal solution is about 60 nm. We have used energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM) and, UV–Vis spectroscopy to characterize the nanoparticles obtained. The energy-dispersive spectroscopy (EDX) of the nanoparticles dispersion confirmed the presence of elemental silver signal no peaks of other impurity were detected. The average size and morphology of silver nanoparticles were determined by transmission electron microscopy (TEM). TEM photographs indicate that the nanopowders consist of well dispersed agglomerates of grains with a narrow size distribution (40 and 60 nm), whereas the radius of the individual particles are between 10 and 20 nm. The synthesized nanoparticles have been structurally characterized by X-ray diffraction and transmission high-energy electron diffraction (HEED). The peaks in the XRD pattern are in good agreement with the standard values of the face-centered-cubic form of metallic silver (ICCD-JCPDS card no. 4-0787) and no peaks of other impurity crystalline phases were detected. Additionally, the antibacterial activity of the nanopart├¡culas dispersion was measured by Kirby-Bauer method. The nanoparticles of silver showed high antimicrobial and bactericidal activity against gram positive bacteria such as Escherichia Coli, Pseudimonas aureginosa and staphylococcus aureus which is a highly methicillin resistant strain.
Abstract: There has been a growing emphasis in
communication management from simple coordination of
promotional tools to a complex strategic process. This study will
examine the current marketing communications and engagement
strategies used in addressing the key stakeholders. In the case of
fertilizer industry in Malaysia, there has been little empirical
research on stakeholder communication when major challenges
facing the modern corporation is the need to communicate its
identity, its values and products in order to distinguish itself from
competitors. The study will employ both quantitative and qualitative
methods and the use of Structural Equation Modeling (SEM) to
establish a causal relationship amongst the key factors of stakeholder
communication strategies and increment in consumers-
choice/acceptance and impact on financial performance. One of the
major contributions is a conceptual framework for communication
strategies and engagement in increasing consumers- acceptance level
and the firm-s financial performance.
Abstract: In this study, fuzzy rule-based classifier is used for the
diagnosis of congenital heart disease. Congenital heart diseases are
defined as structural or functional heart disease. Medical data sets
were obtained from Pediatric Cardiology Department at Selcuk
University, from years 2000 to 2003. Firstly, fuzzy rules were
generated by using medical data. Then the weights of fuzzy rules
were calculated. Two different reasoning methods as “weighted vote
method" and “singles winner method" were used in this study. The
results of fuzzy classifiers were compared.
Abstract: A model of (4, 4) single-walled boron-nitride nanotube as a representative of armchair boron-nitride nanotubes studied. At first the structure optimization performed and then Nuclear Magnetic Resonance parameters (NMR) by Density Functional Theory (DFT) method at 11B and 15N nuclei calculated. Resulted parameters evaluation presents electrostatic environment heterogeneity along the nanotube and especially at the ends but the nuclei in a layer feel the same electrostatic environment. All of calculations carried out using Gaussian 98 Software package.
Abstract: This work is focused on the numerical prediction of the fracture resistance of a flat stiffened panel made of the aluminium alloy 2024 T3 under a monotonic traction condition. The performed numerical simulations have been based on the micromechanical Gurson-Tvergaard (GT) model for ductile damage. The applicability of the GT model to this kind of structural problems has been studied and assessed by comparing numerical results, obtained by using the WARP 3D finite element code, with experimental data available in literature. In the sequel a home-made procedure is presented, which aims to increase the residual strength of a cracked stiffened aluminum panel and which is based on the stochastic design improvement (SDI) technique; a whole application example is then given to illustrate the said technique.
Abstract: Borate minerals have attracted considerable attention in the past years due to their structural chemistry and mechanical properties in several industries. Recently, increasing attention has been paid to the use of; synthetically produced magnesium borates as catalysts reinforcing material for plastics, the conversion of hydrocarbons, electro-conductive treating agent, anti-wear and anti-corrosion materials. Magnesium borates can be synthesized by several methods such as; hydrothermal and solid-state (thermal) processes. In this study the hydrothermal production method was applied at the modest temperature of 80C along with convenient crystal growth. Using MgCl2.6H2O, H3BO3, and NaOH as starting materials, 30, 60, 120, 240 minutes of reaction times were studied. After all, the crystal structure and the morphology of the products were examined by X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR). As a result the forms of Admontite and Mcallisterite minerals were synthesized.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: In this study, Friction Stir Processing (FSP) a recent grain refinement technique was employed to disperse micron-sized (2 *m) SiCp particles into aluminum alloy AA6063. The feasibility to fabricate bulk composites through FSP was analyzed and experiments were conducted at different traverse speeds and wider volumes of the specimens. Micro structural observation were carried out by employing optical microscopy test of the cross sections in both parallel and perpendicular to the tool traverse direction. Mechanical property including micro hardness was evaluated in detail at various regions on the specimen. The composites had an excellent bonding with aluminum alloy substrate and a significant increase of 30% in the micro hardness value of metal matrix composite (MMC) as to that of the base metal has observed. The observations clearly indicate that SiC particles were uniformly distributed within the aluminum matrix.
Abstract: This study examined the underlying dimensions of
brand equity in the chocolate industry. For this purpose, researchers
developed a model to identify which factors are influential in
building brand equity. The second purpose was to assess brand
loyalty and brand images mediating effect between brand attitude,
brand personality, brand association with brand equity. The study
employed structural equation modeling to investigate the causal
relationships between the dimensions of brand equity and brand
equity itself. It specifically measured the way in which consumers’
perceptions of the dimensions of brand equity affected the overall
brand equity evaluations. Data were collected from a sample of
consumers of chocolate industry in Iran. The results of this empirical
study indicate that brand loyalty and brand image are important
components of brand equity in this industry. Moreover, the role of
brand loyalty and brand image as mediating factors in the intention of
brand equity are supported. The principal contribution of the present
research is that it provides empirical evidence of the
multidimensionality of consumer based brand equity, supporting
Aaker´s and Keller´s conceptualization of brand equity. The present
research also enriched brand equity building by incorporating the
brand personality and brand image, as recommended by previous
researchers. Moreover, creating the brand equity index in chocolate
industry of Iran particularly is novel.
Abstract: Structural redundancy is an interesting point in
seismic design of structures. Initially, the structural redundancy is
described as indeterminate degree of a system. Although many definitions are presented for redundancy in structures, recently the
definition of structural redundancy has been related to the configuration of structural system and the number of lateral load
transferring directions in the structure. The steel frames with infill walls are general systems in the constructing of usual residential buildings in some countries. It is
obviously declared that the performance of structures will be affected by adding masonry infill walls. In order to investigate the effect of
infill walls on the redundancy of the steel frame which constructed
with masonry walls, the components of redundancy including redundancy variation index, redundancy strength index and
redundancy response modification factor were extracted for the
frames with masonry infills. Several steel frames with typical storey number and various numbers of bays were designed and considered.
The redundancy of frames with and without infill walls was evaluated by proposed method. The results showed the presence of infill causes increase of redundancy.
Abstract: This paper examines whether or not immigration has a positive influence on the duration of unemployment, in a macroeconomic perspective. We analyse also whether the degree of labor market integration can influence migration. The integration of immigrants into the labor market is a recurrence theme in the work on the economic consequences of immigration. However, to our knowledge, no researchers have studied the impact of immigration on unemployment duration, and vice versa. With two methodology of research (panel estimations (OLS and 2SLS) and panel cointegration techniques), we show that migration seems to influence positively the short-term unemployment and negatively long-term unemployment, for 14 OECD destination countries. In addition, immigration seems to be conditioned by the structural and institutional characteristics of the labour market.
Abstract: Researchers investigate arious strategies to develop composite beams and maximize the structural advantages. This study
attempted to conduct experiments and analysis of changes in the
neutral axis of positive moments of a Green Beam. Strain
compatibility analysis was used, and its efficiency was demonstrated
by comparing experimental and analytical values. In the comparison of
neutral axis, the difference between experimental and analytical values
was found to range from 8.8~26.2%. It was determined that strain
compatibility analysis can be useful for predicting the behaviors of
composite beams, with the ability to predict the behavior of not only
the elastic location of the composite member, but also of the plastic
location
Abstract: In this note, the robust static output feedback
stabilisation of an induction machine is addressed. The machine is
described by a non homogenous bilinear model with structural
uncertainties, and the feedback gain is computed via an iterative LMI
(ILMI) algorithm.