Abstract: IEEE 802.15.4a impulse radio-time hopping ultra wide
band (IR-TH UWB) physical layer, due to small duty cycle and very
short pulse widths is robust against multipath propagation. However,
scattering and reflections with the large number of obstacles in indoor
channel environments, give rise to dense multipath fading. It imposes
serious problem to optimum Rake receiver architectures, for which
very large number of fingers are needed. Presence of strong noise
also affects the reception of fine pulses having extremely low power
spectral density. A robust SRake receiver for IEEE 802.15.4a IRTH
UWB in dense multipath and additive white Gaussian noise
(AWGN) is proposed to efficiently recover the weak signals with
much reduced complexity. It adaptively increases the signal to noise
(SNR) by decreasing noise through a recursive least square (RLS)
algorithm. For simulation, dense multipath environment of IEEE
802.15.4a industrial non line of sight (NLOS) is employed. The power
delay profile (PDF) and the cumulative distribution function (CDF)
for the respective channel environment are found. Moreover, the error
performance of the proposed architecture is evaluated in comparison
with conventional SRake and AWGN correlation receivers. The
simulation results indicate a substantial performance improvement
with very less number of Rake fingers.
Abstract: This paper examines the modeling and analysis of a
cruise control system using a Petri net based approach, task graphs,
invariant analysis and behavioral properties. It shows how the
structures used can be verified and optimized.
Abstract: Arenga pinnata is an abundantly natural fiber that can be used for sound proof material. However, the scientific data of acoustics properties of Arenga pinnata was not available yet. In this study the sound absorption of pure arenga pinnata was measured. The thickness of Arenga pinnata was varied in 10 mm, 20 mm, 30mm, and 40mm. This work was carried out to investigate the potential of using Arenga pinnata fiber as raw material for sound absorbing material. Impedance Tube Method was used to measure sound absorption coefficient (α). The Measurements was done in accordance with ASTM E1050-98, that is the standard test method for impedance and absorption of acoustical materials using a tube, two microphones and a digital frequency analysis system . The results showed that sound absorption coefficients of Arenga pinnata were good from 2000 Hz to 5000 Hz within the range of 0.75 – 0.90. The optimum sound absorption coefficient was obtained from the thickness of 40 mm. These results indicated that Arenga pinnata fiber is promising to be used as raw material of sound absorbing material with low cost, light, and biodegradable.
Abstract: This paper describes Clinical Document Architecture Release Two (CDA R2) standard and a client application for messaging with SAĞLIK-NET project developed by The Ministry of Health of Turkey. CDA R2 , developed by Health Level 7 (HL7) organization and approved by American National Standards Institute (ANSI) in 2004, to standardize medical information to be able to share semantically and syntactically. In this study, a client application compatible with HL7 V3 for a project named SAĞLIKNET, aimed to build a National Health Information System by Turkey. Moreover, CDA conformance of this application will also be evaluated.
Abstract: Tandem mass spectrometry (MS/MS) is the engine
driving high-throughput protein identification. Protein mixtures possibly
representing thousands of proteins from multiple species are
treated with proteolytic enzymes, cutting the proteins into smaller
peptides that are then analyzed generating MS/MS spectra. The
task of determining the identity of the peptide from its spectrum
is currently the weak point in the process. Current approaches to de
novo sequencing are able to compute candidate peptides efficiently.
The problem lies in the limitations of current scoring functions. In this
paper we introduce the concept of proteome signature. By examining
proteins and compiling proteome signatures (amino acid usage) it is
possible to characterize likely combinations of amino acids and better
distinguish between candidate peptides. Our results strongly support
the hypothesis that a scoring function that considers amino acid usage
patterns is better able to distinguish between candidate peptides. This
in turn leads to higher accuracy in peptide prediction.
Abstract: This research presents a system for post processing of
data that takes mined flat rules as input and discovers crisp as well as
fuzzy hierarchical structures using Learning Classifier System
approach. Learning Classifier System (LCS) is basically a machine
learning technique that combines evolutionary computing,
reinforcement learning, supervised or unsupervised learning and
heuristics to produce adaptive systems. A LCS learns by interacting
with an environment from which it receives feedback in the form of
numerical reward. Learning is achieved by trying to maximize the
amount of reward received. Crisp description for a concept usually
cannot represent human knowledge completely and practically. In the
proposed Learning Classifier System initial population is constructed
as a random collection of HPR–trees (related production rules) and
crisp / fuzzy hierarchies are evolved. A fuzzy subsumption relation is
suggested for the proposed system and based on Subsumption Matrix
(SM), a suitable fitness function is proposed. Suitable genetic
operators are proposed for the chosen chromosome representation
method. For implementing reinforcement a suitable reward and
punishment scheme is also proposed. Experimental results are
presented to demonstrate the performance of the proposed system.
Abstract: Mega urban transport projects (MUTPs) are
increasingly being used in urban environments to ameliorate the
problem of congestion. However, a number of problems with regard
to mega projects have been identified. In particular the seemingly
institutionalised over estimation of economic benefits and persistent
cost over runs, could mean that the wrong projects are selected, and
that the projects that are selected cost more than they should. Studies
to date have produced a number of solutions to these problems,
perhaps most notably, the various methods for the inclusion of the
private sector in project provision. However the problems have
shown significant intractability in the face of these solutions. This
paper provides a detailed examination of some of the problems
facing mega projects and then examines Foucault-s theory of
'governmentality' as a possible frame of analysis which might shed
light on the intractability of the problems that have been identified,
through an identification of the art of government in which MUTPs
occur.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: This paper describes a system, in which various methods of text summarizing can be adapted to Polish. A structure of the system is presented. A modular construction of the system and access to the system via the Internet are signaled.
Abstract: The fault current levels through the electric devices
have a significant impact on failure probability. New fault current
results in exceeding the rated capacity of circuit breaker and switching
equipments and changes operation characteristic of overcurrent relay.
In order to solve these problems, SFCL (Superconducting Fault
Current Limiter) has rising as one of new alternatives so as to improve
these problems. A fault current reduction differs depending on
installed location. Therefore, a location of SFCL is very important.
Also, SFCL decreases the fault current, and it prevents surrounding
protective devices to be exposed to fault current, it then will bring a
change of reliability. In this paper, we propose method which
determines the optimal location when SFCL is installed in power
system. In addition, the reliability about the power system which
SFCL was installed is evaluated. The efficiency and effectiveness of
this method are also shown by numerical examples and the reliability
indices are evaluated in this study at each load points. These results
show a reliability change of a system when SFCL was installed.
Abstract: Recordings from recent earthquakes have provided evidence that ground motions in the near field of a rupturing fault differ from ordinary ground motions, as they can contain a large energy, or “directivity" pulse. This pulse can cause considerable damage during an earthquake, especially to structures with natural periods close to those of the pulse. Failures of modern engineered structures observed within the near-fault region in recent earthquakes have revealed the vulnerability of existing RC buildings against pulse-type ground motions. This may be due to the fact that these modern structures had been designed primarily using the design spectra of available standards, which have been developed using stochastic processes with relatively long duration that characterizes more distant ground motions. Many recently designed and constructed buildings may therefore require strengthening in order to perform well when subjected to near-fault ground motions. Fiber Reinforced Polymers are considered to be a viable alternative, due to their relatively easy and quick installation, low life cycle costs and zero maintenance requirements. The objective of this paper is to investigate the adequacy of Artificial Neural Networks (ANN) to determine the three dimensional dynamic response of FRP strengthened RC buildings under the near-fault ground motions. For this purpose, one ANN model is proposed to estimate the base shear force, base bending moments and roof displacement of buildings in two directions. A training set of 168 and a validation set of 21 buildings are produced from FEA analysis results of the dynamic response of RC buildings under the near-fault earthquakes. It is demonstrated that the neural network based approach is highly successful in determining the response.
Abstract: Carbon dioxide capture process has been simulated
and studied under different process conditions. It has been shown
that several process parameters such as lean amine temperature,
number of adsorber stages, number of stripper stages and stripper
pressure affect different process conditions and outputs such as
carbon dioxide removal and reboiler duty. It may be concluded that
the simulation of carbon dioxide capture process can help to estimate
the best process conditions.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. New or upgraded HV infrastructure has safety implications since Transmission mains usually occupy the same easement in the vicinity of neighbouring residents. Transmission mains consist of underground (UG) and overhead (OH) sections and the transition between the UG and OH section is known as the UGOH pole. The existence of two transmission mains in the same easement can dictate to resort to more complicated earthing design in order to mitigate the effect of AC interference, and in some cases it can also necessitates completing a Split Study of the system. This paper provides an overview of the AC interference, Split Study and the earthing of an underground feeder including the UGOH pole .In addition, this paper discusses the use of different link boxes on the UG feeder and presents a case study that represent a clear example of the Ac interference and Split factor. Finally, a few recommendations are provided to achieve a safety zone in the area beyond the boundary of the HV system.
Abstract: This paper presents an iterative algorithm to find a
inverse kinematic solution of 5-DOF robot. The algorithm is to
minimize the iteration number. Since the 5-DOF robot cannot give full
orientation of tool. Only z-direction of tool is satisfied while rotation
of tool is determined by kinematic constraint. This work therefore
described how to specify the tool direction and let the tool rotation free.
The simulation results show that this algorithm effectively worked.
Using the proposed iteration algorithm, error due to inverse kinematics
converged to zero rapidly in 5 iterations. This algorithm was applied in
real welding robot and verified through various practical works.
Abstract: The performance of modified Fenton (MF) treatment
to promote PAH oxidation in artificially contaminated soil was
investigated in packed soil column with a hydrogen peroxide (H2O2)
delivery system simulating in situ injection. Soil samples were spiked
with phenanthrene (low molecular weight PAH) and fluoranthene
(high molecular weight PAH) to an initial concentration of 500
mg/kg dried soil each. The effectiveness of process parameters
H2O2/soil, iron/soil, chelating agent/soil weight ratios and reaction
time were studied using a 24 three level factorial design experiments.
Statistically significant quadratic models were developed using
Response Surface Methodology (RSM) for degrading PAHs from the
soil samples. Optimum operating condition was achieved at mild
range of H2O2/soil, iron/soil and chelating agent/soil weight ratios,
indicating cost efficient method for treating highly contaminated
lands.
Abstract: Microwave energy can be used for drying purpose. It is unique process. It is distinctly different from conventional drying process. It is advantageous over conventional drying / heating processes. When microwave energy is used for drying purpose, the process can be accelerated with a better control to achieve uniform heating, more conversion efficiency, selective drying and ultimately improved product quality of the output. Also, less floor space and compact system are the added advantages. Existing low power microwave drying system is to be modified with suitable applicator. Appropriate sensors are to be used to measure parameters like moisture, temperature, weight of sample. Suitable high tech controller is to be used to control microwave power continuously from minimum to maximum. Phase - controller, cycle - controller and PWM - controller are some of the advanced power control techniques. It has been proposed to work on turmeric using high-tech phase controller to control the microwave power conveniently. The drying of turmeric with microwave energy employing phase controller gives better results as formulated in this paper and hence new approach of processing turmeric will open future doors of profit making to allied industries and the farmers.
Abstract: The quality-of-service (QoS) support for wireless
LANs has been a hot research topic during the past few years. In this paper, two QoS provisioning mechanisms are proposed for the employment in 802.11e EDCA MAC scheme. First, the proposed call
admission control mechanism can not only guarantee the QoS for the higher priority existing connections but also provide the minimum reserved bandwidth for traffic flows with lower priority. In addition, the adaptive contention window adjustment mechanism can adjust the
maximum and minimum contention window size dynamically according to the existing connection number of each AC. The collision
probability as well as the packet delay will thus be reduced effectively.
Performance results via simulations have revealed the enhanced QoS property achieved by employing these two mechanisms.
Abstract: Scheduling algorithm is a key technology in satellite
switching system with input-buffer. In this paper, a new scheduling
algorithm and its realization are proposed. Based on Crossbar
switching fabric, the algorithm adopts serial scheduling strategy and
adjusts the output port arbitrating strategy for the better equity of every
port. Consequently, it increases the matching probability. The
algorithm can greatly reduce the scheduling delay and cell loss rate.
The analysis and simulation results by OPNET show that the proposed
algorithm has the better performance than others in average delay and
cell loss rate, and has the equivalent complexity. On the basis of these
results, the hardware realization and simulation based on FPGA are
completed, which validate the feasibility of the new scheduling
algorithm.
Abstract: an intelligent BRT system is necessary when
communities looking for new ways to use high capacity rapid transit
at a reduced cost.This paper will describe the intelligent control
system that works with Datacenter. With the help of GPS system, the
data center can monitor the situation of each bus and bus station.
Through RFID technology, bus station and traffic light can transfer
data with bus and by Wimax communication technology all of parts
can talk together; data center learns all information about the location
of bus, the arrival of bus in each station and the number of passengers
in station and bus.Finally, the paper presents the case study of those
theories in Tehran BRT.
Abstract: The primary objective of this research is to improve the flexural capacity of FRP strengthened RC Beam structures with Aluminum and Titanium laminates. FRP rupture of flexural strengthened RC beams using FRP plates generally occurs at the interface between FRP plate and the beam. Therefore, in order to prevent brittle rupture and improve the ductility of the system, this research was performed by using Aluminum and Titanium materials between the two different structural systems. The research also aims to provide various strengthening/retrofitting methods for RC beam structures and to conduct a preliminary analysis of the demands on the structural systems. This was achieved by estimation using the experimental data from this research to identify a flexural capacity for the systems. Ultimately, the preliminary analysis of current study showed that the flexural capacity and system demand ductility was significantly improved by the systems inserted with Aluminum and Titanium anchor plates. Further verification of the experimental research is currently on its way to develop a new or reliable design guideline to retrofit/strengthen the concrete-FRP structural system can be evaluated.