Abstract: In this study, we illustrated the performance and
microbial community of single- and two-phase systems anaerobically
co-digesting cassava pulp and pig manure. The results showed that
the volatile solid reduction and biogas productivity of two-phase
CSTR were 66 ± 4% and 2000 ± 210 ml l-1 d-1, while those of singlephase
CSTR were 59 ± 1% and 1670 ± 60 ml l-1 d-1, respectively. Codigestion
in two-phase CSTR gave higher 12% solid degradation and
25% methane production than single-phase CSTR. Phylogenetic
analysis of 16S rDNA clone library revealed that the Bacteroidetes
were the most abundant group, followed by the Clostridia in singlephase
CSTR. In hydrolysis/acidification reactor of two-phase system,
the bacteria within the phylum Firmicutes, especially Clostridium,
Eubacteriaceae and Lactobacillus were the dominant phylogenetic
groups. Among the Archaea, Methanosaeta sp. was the exclusive
predominant in both digesters while the relative abundance of
Methanosaeta sp. and Methanospirillum hungatei differed between
the two systems.
Abstract: Greenhouse gases (GHG) emissions impose major
threat to global warming potential (GWP). Unfortunately
manufacturing sector is one of the major sources that contribute
towards the rapid increase in greenhouse gases (GHG) emissions. In
manufacturing sector electric power consumption is the major driver
that influences CO2 emission. Titanium alloys are widely utilized in
aerospace, automotive and petrochemical sectors because of their
high strength to weight ratio and corrosion resistance. Titanium
alloys are termed as difficult to cut materials because of their poor
machinability rating. The present study analyzes energy consumption
during cutting with reference to material removal rate (MRR).
Surface roughness was also measured in order to optimize energy
consumption.
Abstract: This study offers a new simple method for assessing
an axial part-through crack in a pipe wall. The method utilizes simple
approximate expressions for determining the fracture parameters K,
J, and employs these parameters to determine critical dimensions of a
crack on the basis of equality between the J-integral and the J-based
fracture toughness of the pipe steel. The crack tip constraint is taken
into account by the so-called plastic constraint factor C, by which the
uniaxial yield stress in the J-integral equation is multiplied. The
results of the prediction of the fracture condition are verified by burst
tests on test pipes.
Abstract: Air infiltration in mass scale industrial applications of
bio char production is inevitable. The presence of oxygen during the
carbonization process is detrimental to the production of biochar yield
and properties. The experiment was carried out on several wood
species in a fixed-bed pyrolyser under various fractions of oxygen
ranging from 0% to 11% by varying nitrogen and oxygen composition
in the pyrolysing gas mixtures at desired compositions. The bed
temperature and holding time were also varied. Process optimization
was carried out by Response Surface Methodology (RSM) by
employing Central Composite Design (CCD) using Design Expert 6.0
Software. The effect of oxygen ratio and holding time on biochar yield
within the range studied were statistically significant. From the
analysis result, optimum condition of 15.2% biochar yield of
mangrove wood was predicted at pyrolysis temperature of 403 oC,
oxygen percentage of 2.3% and holding time of two hours. This
prediction agreed well with the experiment finding of 15.1% biochar
yield.
Abstract: In this study, the kinetic of biogas production was studied by performing a series laboratory experiment using rumen fluid of animal ruminant as inoculums. Cattle manure as substrate was inoculated by rumen fluid to the anaerobic biodigester. Laboratory experiments using 400 ml biodigester were performed in batch operation mode. Given 100 grams of fresh cattle manure was fed to each biodigester and mixed with rumen fluid by manure : rumen weight ratio of 1:1 (MR11). The operating temperatures were varied at room temperature and 38.5 oC. The cumulative volume of biogas produced was used to measure the biodigester performance. The research showed that the rumen fluid inoculated to biodigester gave significant effect to biogas production (P
Abstract: Landfill gas, particularly methane is one of the
greenhouse gases which contributes to global warming. This paper presents the findings of a study on methane gas production from
simulated landfill reactor under saturated conditions. A reactor was constructed to represent a landfill cell of 2.5 m thickness on sandy
soil. The reactor was 0.2 m in diameter and 4 m in height. One meter of sand and pebble layer was packed at the bottom of the reactor
followed by 2.5 m of solid waste layer and 0.4 m of sand layer as the cover soil. Degradation of waste in the solid waste layer was at
acidification stage as indicated by the leachate quality with COD as
high as 55,511 mg/L and pH as low as 5.1. However, methanogenic
environment was established at the bottom sand layer after one year of operation indicated by pH of 7.2 and methane gas generation.
Leachate degradation took place as the leachate moved through the
sand layer at an infiltration of rate 0.7 cm/day. This resulted in landfill gas production of 77 mL/day/kg containing 55 to 65% methane. The application of sand layer contributed to the gas
production from landfill by an in-situ degradation of leachate in the
sand at the bottom of the landfill.
Abstract: In this contribution an innovative platform is being
presented that integrates intelligent agents and evolutionary
computation techniques in legacy e-learning environments. It
introduces the design and development of a scalable and
interoperable integration platform supporting:
I) various assessment agents for e-learning environments,
II) a specific resource retrieval agent for the provision of
additional information from Internet sources matching the
needs and profile of the specific user and
III) a genetic algorithm designed to extract efficient information
(classifying rules) based on the students- answering input
data.
The agents are implemented in order to provide intelligent
assessment services based on computational intelligence techniques
such as Bayesian Networks and Genetic Algorithms.
The proposed Genetic Algorithm (GA) is used in order to extract
efficient information (classifying rules) based on the students-
answering input data. The idea of using a GA in order to fulfil this
difficult task came from the fact that GAs have been widely used in
applications including classification of unknown data.
The utilization of new and emerging technologies like web
services allows integrating the provided services to any web based
legacy e-learning environment.
Abstract: Although automotive industry has brought different beneficiaries to human life, it is being pointed out as one of the major cause of global air pollution which resulted in climate change, smog, green house gases (GHGs), and human diseases by many reasons. Since auto industry is one of the largest consumers of fossil fuels, the realization of green innovations is becoming a crucial choice to meet the challenges towards sustainable development. Recently, many auto manufacturers have embarked on green technology initiatives to gain a competitive advantage in the global market; however, innovative manufacturing systems and technologies can enhance operational performance only if the human resource management is in place to elicit the motivation of the employees and develop their organizational expertise. No organization can perform at peak levels unless each employee is committed to the company goals and works as an effective team member. Strategic human resource practices are the primary means by which firms can shape the skills, attitudes, and behavior of individuals to align with the business strategic objectives. This study investigates on the comprehensive approach of multiple advanced technology innovations and human resource management at Toyota Motor Corporation as the market leader of full hybrid technology in the automotive industry. Then, HRM framework of the company is described and three sets of human resource practices that support the innovation-oriented HR system, presented. Finally, a conceptual framework for innovativeness in green technology in automotive industry by applying a deliberate strategic HR management system and knowledge management with the intervening factors of organizational culture, knowledge application and knowledge sharing is proposed.
Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: Cashew nut shells were converted into activated carbon powders using KOH activation plus CO2 gasification at 1027 K. The increase both of impregnation ratio and activation time, there was swiftly the development of mesoporous structure with increasing of mesopore volume ratio from 20-28% and 27-45% for activated carbon with ratio of KOH per char equal to 1 and 4, respectively. Activated carbon derived from KOH/char ratio equal to 1 and CO2 gasification time from 20 to 150 minutes were exhibited the BET surface area increasing from 222 to 627 m2.g-1. And those were derived from KOH/char ratio of 4 with activation time from 20 to 150 minutes exhibited high BET surface area from 682 to 1026 m2.g-1. The adsorption of Lead(II) and Cadmium(II) ion was investigated. This adsorbent exhibited excellent adsorption for Lead(II) and Cadmium(II) ion. Maximum adsorption presented at 99.61% at pH 6.5 and 98.87% at optimum conditions. The experimental data was calculated from Freundlich isotherm and Langmuir isotherm model. The maximum capacity of Pb2+ and Cd2+ ions was found to be 28.90 m2.g-1 and 14.29 m2.g-1, respectively.
Abstract: This study addresses the effect of impurities on the
crystallization of Na2CO3 produced within a strategy for capturing
CO2 from flue gases by alkaline absorption. A novel technology -
membrane assisted crystallization - is proposed for Na2CO3
crystallization from mother liquors containing impurities. High purity
of Na2CO3•10H2O crystals was obtained without impacting the
performance of the mass transfer of water vapor through membranes
during crystallization.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: The study investigated the effects of Teaching Games
for Understanding approach on students ‘cognitive learning outcome.
The study was a quasi-experimental non-equivalent pretest-posttest
control group design whereby 10 year old primary school students
(n=72) were randomly assigned to an experimental and a control
group. The experimental group students were exposed with TGfU
approach and the control group with the Traditional Skill approach of
handball game. Game Performance Assessment Instrument (GPAI)
was used to measure students' tactical understanding and decision
making in 3 versus 3 handball game situations. Analysis of
covariance (ANCOVA) was used to analyze the data. The results
reveal that there was a significant difference between the TGfU
approach group and the traditional skill approach group students on
post test score (F (1, 69) = 248.83, p < .05). The findings of this
study suggested the importance of TGfU approach to improve
primary students’ tactical understanding and decision making in
handball game.
Abstract: In mechanical and environmental engineering, mixed
convection is a frequently encountered thermal fluid phenomenon
which exists in atmospheric environment, urban canopy flows, ocean
currents, gas turbines, heat exchangers, and computer chip cooling
systems etc... . This paper deals with a numerical investigation of
mixed convection in a vertical heated channel. This flow results from
the mixing of the up-going fluid along walls of the channel with the
one issued from a flat nozzle located in its entry section. The fluiddynamic
and heat-transfer characteristics of vented vertical channels
are investigated for constant heat-flux boundary conditions, a
Rayleigh number equal to 2.57 1010, for two jet Reynolds number
Re=3 103 and 2104 and the aspect ratio in the 8-20 range. The system
of governing equations is solved with a finite volumes method and an
implicit scheme. The obtained results show that the turbulence and
the jet-wall interaction activate the heat transfer, as does the drive of
ambient air by the jet. For low Reynolds number Re=3 103, the
increase of the aspect Ratio enhances the heat transfer of about 3%,
however; for Re=2 104, the heat transfer enhancement is of about
12%. The numerical velocity, pressure and temperature fields are
post-processed to compute the quantities of engineering interest such
as the induced mass flow rate, and average Nusselt number, in terms
of Rayleigh, Reynolds numbers and dimensionless geometric
parameters are presented.
Abstract: The paper depicts air velocity values, reproduced by laser Doppler anemometer (LDA) and ultrasonic anemometer (UA), relations with calculated ones from flow rate measurements using the gas meter which calibration uncertainty is ± (0.15 – 0.30) %. Investigation had been performed in channel installed in aerodynamical facility used as a part of national standard of air velocity. Relations defined in a research let us confirm the LDA and UA for air velocity reproduction to be the most advantageous measures. The results affirm ultrasonic anemometer to be reliable and favourable instrument for measurement of mean velocity or control of velocity stability in the velocity range of 0.05 m/s – 10 (15) m/s when the LDA used. The main aim of this research is to investigate low velocity regularities, starting from 0.05 m/s, including region of turbulent, laminar and transitional air flows. Theoretical and experimental results and brief analysis of it are given in the paper. Maximum and mean velocity relations for transitional air flow having unique distribution are represented. Transitional flow having distinctive and different from laminar and turbulent flow characteristics experimentally have not yet been analysed.
Abstract: A techno-economic evaluation for efficient use of
energy in a large scale industrial plant of methanol is carried out.
This assessment is based on integration of a gas turbine with an
existing plant of methanol in which the outlet gas products of
exothermic reactor is expanded to power generation. Also, it is
decided that methanol production rate is constant through addition of
power generation system to the existing methanol plant. Having
incorporated a gas turbine with the existing plant, the economic
results showed total investment of MUSD 16.9, energy saving of 3.6
MUSD/yr with payback period of approximately 4.7 years.
Abstract: Gas chromatography (GC) is the most widely used
technique in analytical chemistry. However, GC has high initial cost
and requires frequent maintenance. This paper examines the
feasibility and potential of using a neural network model as an
alternative whenever GC is unvailable. It can also be part of system
verification on the performance of GC for preventive maintenance
activities. It shows the performance of MultiLayer Perceptron (MLP)
with Backpropagation structure. Results demonstrate that neural
network model when trained using this structure provides an
adequate result and is suitable for this purpose. cm.
Abstract: Solid waste can be considered as an urban burden or
as a valuable resource depending on how it is managed. To meet the
rising demand for energy and to address environmental concerns, a
conversion from conventional energy systems to renewable resources
is essential. For the sustainability of human civilization, an
environmentally sound and techno-economically feasible waste
treatment method is very important to treat recyclable waste. Several
technologies are available for realizing the potential of solid waste as
an energy source, ranging from very simple systems for disposing of
dry waste to more complex technologies capable of dealing with
large amounts of industrial waste. There are three main pathways for
conversion of waste material to energy: thermo chemical,
biochemical and physicochemical. This paper investigates the thermo
chemical conversion of solid waste for energy recovery. The
processes, advantages and dis-advantages of various thermo chemical
conversion processes are discussed and compared. Special attention
is given to Gasification process as it provides better solutions
regarding public acceptance, feedstock flexibility, near-zero
emissions, efficiency and security. Finally this paper presents
comparative statements of thermo chemical processes and introduces
an integrated waste management system.