Abstract: Waste management is now a global concern due to its
high environmental impact on climate change. Because of generating
huge amount of waste through our daily activities, managing waste in
an efficient way has become more important than ever. Alternative
Waste Technology (AWT), a new category of waste treatment
technology has been developed for energy recovery in recent years to
address this issue. AWT describes a technology that redirects waste
away from landfill, recovers more useable resources from the waste
flow and reduces the impact on the surroundings. Australia is one of
the largest producers of waste per-capita. A number of AWTs are
using in Australia to produce energy from waste. Presently, it is vital
to identify an appropriate AWT to establish a sustainable waste
management system in Australia. Identification of an appropriate
AWT through Multi-criteria analysis (MCA) of four AWTs by using
five key decision making criteria is presented and discussed in this
paper.
Abstract: As the demand and prices of various petroleum products have been on the rise in recent years, there is a growing need for alternative fuels. Biodiesel, which consists of alkyl monoesters of fatty acids from vegetable oils and animal fats, is considered as an alternative to petroleum diesel. Biodiesel has comparable performance with that of diesel and has lower brake specific fuel consumption than diesel with significant reduction in emissions of CO, hydrocarbons (HC) and smoke with however, a slight increase in NOx emissions. This paper analyzes the effect of cooled exhaust gas recirculation in the combustion characteristics of a direct injection compression ignition engine using biodiesel blended fuel as opposed to the conventional system. The combustion parameters such as cylinder pressure, heat release rate, delay period and peak pressure were analyzed at various loads. The maximum cylinder pressure reduces as the fraction of biodiesel increases in the blend the maximum rate of pressure rise was found to be higher for diesel at higher engine loads.
Abstract: This study investigates CO2 mitigation by methanol
synthesis from flue gas CO2 and H2 generation through water
electrolysis. Electrolytic hydrogen generation is viable provided that
the required electrical power is supplied from renewable energy
resources; whereby power generation from renewable resources is yet
commercial challenging. This approach contribute to zero-emission,
moreover it produce oxygen which could be used as feedstock for
chemical process. At ZPC, however, oxygen would be utilized
through partial oxidation of methane in autothermal reactor (ATR);
this makes ease the difficulties of O2 delivery and marketing. On the
other hand, onboard hydrogen storage and consumption; in methanol
plant; make the project economically more competitive.
Abstract: Hydrate phase equilibria for the binary CO2+water and
CH4+water mixtures in silica gel pore of nominal diameters 6, 30, and
100 nm were measured and compared with the calculated results based
on van der Waals and Platteeuw model. At a specific temperature,
three-phase hydrate-water-vapor (HLV) equilibrium curves for pore
hydrates were shifted to the higher-pressure condition depending on
pore sizes when compared with those of bulk hydrates. Notably,
hydrate phase equilibria for the case of 100 nominal nm pore size were
nearly identical with those of bulk hydrates. The activities of water in
porous silica gels were modified to account for capillary effect, and
the calculation results were generally in good agreement with the
experimental data. The structural characteristics of gas hydrates in
silica gel pores were investigated through NMR spectroscopy.
Abstract: The purpose of this paper is to propose a framework for constructing correct parallel processing programs based on Equivalent Transformation Framework (ETF). ETF regards computation as In the framework, a problem-s domain knowledge and a query are described in definite clauses, and computation is regarded as transformation of the definite clauses. Its meaning is defined by a model of the set of definite clauses, and the transformation rules generated must preserve meaning. We have proposed a parallel processing method based on “specialization", a part of operation in the transformations, which resembles substitution in logic programming. The method requires “Memo-tree", a history of specialization to maintain correctness. In this paper we proposes the new method for the specialization-base parallel processing without Memo-tree.
Abstract: This paper describes technological possibilities to
enhance methane productionin the anaerobic stabilization of wastewater treatment plant excess sludge. This objective can be achieved by the addition of waste residues: crude glycerol from biodiesel production and residues from fishery. The addition
ofglycerol in an amount by weight of 2 – 5% causes enhancement of methane production of about 250 – 400%. At the same time the
percentage increase of total solids concentration in the outgoing sludge is ten or more times less. The containment of methane in
biogas is higher in case of admixed substrate.
Abstract: At the previous study of new metal gasket, contact
width and contact stress were important design parameter for
optimizing metal gasket performance. However, the range of contact
stress had not been investigated thoroughly. In this study, we
conducted a gasket design optimization based on an elastic and plastic
contact stress analysis considering forming effect using FEM. The
gasket model was simulated by using two simulation stages which is
forming and tightening simulation. The optimum design based on an
elastic and plastic contact stress was founded. Final evaluation was
determined by helium leak quantity to check leakage performance of
both type of gaskets. The helium leak test shows that a gasket based
on the plastic contact stress design better than based on elastic stress
design.
Abstract: In this research, an anaerobic co-digestion using decanter cake from palm oil mill industry to improve the biogas production from frozen seafood wastewater is studied using Continuously Stirred Tank Reactor (CSTR) process. The experiments were conducted in laboratory-scale. The suitable Hydraulic Retention Time (HRT) was observed in CSTR experiments with 24 hours of mixing time using the mechanical mixer. The HRT of CSTR process impacts on the efficiency of biogas production. The best performance for biogas production using CSTR process was the anaerobic codigestion for 20 days of HRT with the maximum methane production rate of 1.86 l/d and the average maximum methane production of 64.6%. The result can be concluded that the decanter cake can improve biogas productivity of frozen seafood wastewater.
Abstract: In the present study, development of salbutamol
sulphate nanoparticles that adhere to gastric mucus was investigated.
Salbutamol sulphate has low bioavailability due to short transit time in
gastric. It also has a positive surface charge that provides hurdles to be
encapsulated by the positively strong mucoadhesive polymer of
chitosan. To overcome the difficulties, the surface charge of active
ingredient was modified using several nonionic and anionic
stomach-specific polymers. The nanoparticles were prepared using
ionotropic gelation technique. The evaluation involved determination
of particle size, zeta potential, entrapment efficiency, in vitro drug
release and in vitro mucoadhesion test. Results exhibited that the use
of anionic alginate polymer was more satisfactory than that of
nonionic polymer. Characteristics of the particles was nano-size, high
encapsulation efficiency, fulfilled the drug release requirements and
adhesive towards stomach for around 11 hours. This result shows that
the salbutamol sulphate nanoparticles can be utilized for improvement
its delivery.
Abstract: The use of renewable energy sources incl. biogas has become topical in accordance with the increasing demand for energy, decrease of fossil energy resources and the efforts to reduce greenhouse gas emissions as well as to increase energy independence from the territories where fossil energy resources are available.
As the technologies of biogas production from agricultural biomass develop, risk assessment and risk management become necessary for farms producing such a renewable energy. The need for risk assessments has become particularly topical when discussions on changing the biogas policy in the EU take place, which may influence the development of the sector in the future, as well as the operation of existing biogas facilities and their income level.
The current article describes results of the risk assessment for farms producing biomass from agriculture biomass in Latvia, the risk assessment system included 24 risks, that affect the whole biogas production process and the obtained results showed the high significance of political and production risks.
Abstract: The implementation of Super-Ultra Low Emission
Vehicle standards requires more efficient exhaust gas purification. To
increase the efficiency of exhaust gas purification, an the adsorbent
capable of holding hydrocarbons up to 250-300 ОС should be
developed. The possibility to design such adsorbents by modification
of zeolites of mordenite type, ZSM-5 and NaY, using different
metals cations has been studied.
It has been shown that introducing Cr, Cs, Zn, Ni, Co, Li, Mn in
zeolites results in modification of the toluene TPD and toluene
sorption capacity.
5%LiZSM-5 zeolite exhibits the most attractive TPD curve, with
toluene desorption temperature ranging from 250 to 350ОС. The
sorption capacity of 5%Li-ZSM-5 is 0.4 mmol/g. NaY zeolite has the
highest sorption capacity, up to 2 mmol/g, and holds toluene up to
350ОС, but at 120ОС toluene desorption starts, which is not desirable,
since the adsorbent of cold start hydrocarbons should retain them
until 250-300ОС. Therefore 5%LiZSM-5 zeolite was found to be the
most promising to control the cold-start hydrocarbon emissions
among the samples studied.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: Buyer coalition with a combination of items is a group of buyers joining together to purchase a combination of items with a larger discount. The primary aim of existing buyer coalition with a combination of items research is to generate a large total discount. However, the aim is hard to achieve because this research is based on the assumption that each buyer completely knows other buyers- information or at least one buyer knows other buyers- information in a coalition by exchange of information. These assumption contrast with the real world environment where buyers join a coalition with incomplete information, i.e., they concerned only with their expected discounts. Therefore, this paper proposes a new buyer community coalition formation with a combination of items scheme, called the Community Compromised Combinatorial Coalition scheme, under such an environment of incomplete information. In order to generate a larger total discount, after buyers who want to join a coalition propose their minimum required saving, a coalition structure that gives a maximum total retail prices is formed. Then, the total discount division of the coalition is divided among buyers in the coalition depending on their minimum required saving and is a Pareto optimal. In mathematical analysis, we compare concepts of this scheme with concepts of the existing buyer coalition scheme. Our mathematical analysis results show that the total discount of the coalition in this scheme is larger than that in the existing buyer coalition scheme.
Abstract: Inconel 718, a nickel based super-alloy is an
extensively used alloy, accounting for about 50% by weight of
materials used in an aerospace engine, mainly in the gas turbine
compartment. This is owing to their outstanding strength and
oxidation resistance at elevated temperatures in excess of 5500 C.
Machining is a requisite operation in the aircraft industries for the
manufacture of the components especially for gas turbines. This
paper is concerned with optimization of the surface roughness when
turning Inconel 718 with cermet inserts. Optimization of turning
operation is very useful to reduce cost and time for machining. The
approach is based on Response Surface Method (RSM). In this work,
second-order quadratic models are developed for surface roughness,
considering the cutting speed, feed rate and depth of cut as the cutting
parameters, using central composite design. The developed models
are used to determine the optimum machining parameters. These
optimized machining parameters are validated experimentally, and it
is observed that the response values are in reasonable agreement with
the predicted values.
Abstract: The mixing behaviors of dry and wet granular
materials in gas fluidized bed systems were investigated
computationally using the combined Computational Fluid Dynamics
and Discrete Element Method (CFD-DEM). Dry particles were
observed to mix fairly rapidly during the fluidization process due to
vigorous relative motions between particles induced by the flow of
gas. In contrast, due to the presence of strong cohesive forces arising
from capillary liquid bridges between wet particles, the mixing
efficiencies of wet granular materials under similar operating
conditions were observed to be reduced significantly.
Abstract: Due to the call of global warming effects, city planners aim at actions for reducing carbon emission. One of the approaches is to promote the usage of public transportation system toward the transit-oriented-development. For example, rapid transit system in Taipei city and Kaohsiung city are opening. However, until November 2008 the average daily patronage counted only 113,774 passengers at Kaohsiung MRT systems, much less than which was expected. Now the crucial questions: how the public transport competes with private transport? And more importantly, what factors would enhance the use of public transport? To give the answers to those questions, our study first applied regression to analyze the factors attracting people to use public transport around cities in the world. It is shown in our study that the number of MRT stations, city population, cost of living, transit fare, density, gasoline price, and scooter being a major mode of transport are the major factors. Subsequently, our study identified successful and unsuccessful cities in regard of the public transport usage based on the diagnosis of regression residuals. Finally, by comparing transportation strategies adopted by those successful cities, our conclusion stated that Kaohsiung City could apply strategies such as increasing parking fees, reducing parking spaces in downtown area, and reducing transfer time by providing more bus services and public bikes to promote the usage of public transport.
Abstract: In order to compare the performance of the carbon dioxide and HFC-125 heat pumps for medium-and high-temperature heating, both heat pump cycles were optimized using a simulation method. To fairly compare the performance of the cycles by using different working fluids, each cycle was optimized from the viewpoint of heating COP by two design parameters. The first is the gas cooler exit temperature and the other is the ratio of the overall heat conductance of the gas cooler to the combined overall heat conductance of the gas cooler and the evaporator. The inlet and outlet temperatures of secondary fluid of the gas cooler were fixed at 40/90°C and 40/150°C.The results shows that the HFC-125 heat pump has 6% higher heating COP than carbon dioxide heat pump when the heat sink exit temperature is fixed at 90ºC, while the latter outperforms the former when the heat sink exit temperature is fixed at 150ºC under the simulation conditions considered in the present study.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: In this research, a biofiltration process to remove
ammonia gas from gas stream using agricultural residue biofilter
medias is studied. The experiments were conducted in laboratoryscale
biofilter. The biofilter medias were a mixture of manure
fertilizer and bagasse at various ratios i.e., 1:3, 1:5 and 1:7. The
experiments were performed for a period of 40 days. The empty bed
retention time (EBRT) is 78s. The moisture content of biofilter media
was maintained at 45-60% using water. The results showed that the
agricultural residues (manure fertilizer and bagasse) are suitable as
biofilter media for ammonia gas removal in biofiltration process.
The maximum efficiency of ammonia gas removal is observed
from the 1:5 of manure fertilizer: bagasse ratio at 89.93%. The
biofiltration is more effective at low ammonia gas concentration. In
addition, the mixture ratio of biofilter media is not a significant factor
in biofiltration operation while the most significant factor for
biofiltration operation is the inlet ammonia gas concentration.
Abstract: The study of non-equilibrium systems has attracted
increasing interest in recent years, mainly due to the lack of
theoretical frameworks, unlike their equilibrium counterparts.
Studying the steady state and/or simple systems is thus one of the
main interests. Hence in this work we have focused our attention on
the driven lattice gas model (DLG model) consisting of interacting
particles subject to an external field E. The dynamics of the system
are given by hopping of particles to nearby empty sites with rates
biased for jumps in the direction of E. Having used small two
dimensional systems of DLG model, the stochastic properties at nonequilibrium
steady state were analytically studied. To understand the
non-equilibrium phenomena, we have applied the analytic approach
via master equation to calculate probability function and analyze
violation of detailed balance in term of the fluctuation-dissipation
theorem. Monte Carlo simulations have been performed to validate
the analytic results.