Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The objective of this study was to improve our
understanding of vulnerability and environmental change; it's causes
basically show the intensity, its distribution and human-environment
effect on the ecosystem in the Apodi Valley Region, This paper is
identify, assess and classify vulnerability and environmental change
in the Apodi valley region using a combined approach of landscape
pattern and ecosystem sensitivity. Models were developed using the
following five thematic layers: Geology, geomorphology, soil,
vegetation and land use/cover, by means of a Geographical
Information Systems (GIS)-based on hydro-geophysical parameters.
In spite of the data problems and shortcomings, using ESRI-s ArcGIS
9.3 program, the vulnerability score, to classify, weight and combine
a number of 15 separate land cover classes to create a single indicator
provides a reliable measure of differences (6 classes) among regions
and communities that are exposed to similar ranges of hazards.
Indeed, the ongoing and active development of vulnerability
concepts and methods have already produced some tools to help
overcome common issues, such as acting in a context of high
uncertainties, taking into account the dynamics and spatial scale of
asocial-ecological system, or gathering viewpoints from different
sciences to combine human and impact-based approaches. Based on
this assessment, this paper proposes concrete perspectives and
possibilities to benefit from existing commonalities in the
construction and application of assessment tools.
Abstract: The Wavelet-Galerkin finite element method for
solving the one-dimensional heat equation is presented in this work.
Two types of basis functions which are the Lagrange and multi-level
wavelet bases are employed to derive the full form of matrix system.
We consider both linear and quadratic bases in the Galerkin method.
Time derivative is approximated by polynomial time basis that
provides easily extend the order of approximation in time space. Our
numerical results show that the rate of convergences for the linear
Lagrange and the linear wavelet bases are the same and in order 2
while the rate of convergences for the quadratic Lagrange and the
quadratic wavelet bases are approximately in order 4. It also reveals
that the wavelet basis provides an easy treatment to improve
numerical resolutions that can be done by increasing just its desired
levels in the multilevel construction process.
Abstract: During the last years, the genomes of more and more
species have been sequenced, providing data for phylogenetic recon-
struction based on genome rearrangement measures. A main task in
all phylogenetic reconstruction algorithms is to solve the median of
three problem. Although this problem is NP-hard even for the sim-
plest distance measures, there are exact algorithms for the breakpoint
median and the reversal median that are fast enough for practical use.
In this paper, this approach is extended to the transposition median as
well as to the weighted reversal and transposition median. Although
there is no exact polynomial algorithm known even for the pairwise
distances, we will show that it is in most cases possible to solve
these problems exactly within reasonable time by using a branch and
bound algorithm.
Abstract: This paper focuses on testing database of existing
information system. At the beginning we describe the basic problems
of implemented databases, such as data redundancy, poor design of
database logical structure or inappropriate data types in columns of
database tables. These problems are often the result of incorrect
understanding of the primary requirements for a database of an
information system. Then we propose an algorithm to compare the
conceptual model created from vague requirements for a database
with a conceptual model reconstructed from implemented database.
An algorithm also suggests steps leading to optimization of
implemented database. The proposed algorithm is verified by an
implemented prototype. The paper also describes a fuzzy system
which works with the vague requirements for a database of an
information system, procedure for creating conceptual from vague
requirements and an algorithm for reconstructing a conceptual model
from implemented database.
Abstract: This paper proposes a novel stereo vision technique
for top view book scanners which provide us with dense 3d point
clouds of page surfaces. This is a precondition to dewarp bound
volumes independent of 2d information on the page. Our method is
based on algorithms, which normally require the projection of pattern
sequences with structured light. We use image sequences of the
moving stripe lighting of the top view scanner instead of an additional
light projection. Thus the stereo vision setup is simplified without
losing measurement accuracy. Furthermore we improve a surface
model dewarping method through introducing a difference vector
based on real measurements. Although our proposed method is hardly
expensive neither in calculation time nor in hardware requirements
we present good dewarping results even for difficult examples.
Abstract: Organizational culture fosters innovation, and innovation is the main engine to be sustained within the uncertainty market. Like other countries, the construction industry significantly contributes to the economy, society and technology of Malaysia, yet, innovation is still considered slow compared to other industries such as manufacturing. Given the important role of an architect as the key player and the contributor of new ideas in the construction industry, there is a call to identify the issue and improve the current situation by focusing on the architectural firms. In addition, the existing studies tend to focus only on a few dimensions of organizational culture and very few studies consider whether innovation is being generated or adopted. Hence, the present research tends to fill in the gap by identifying the organizational cultures that foster or hinder innovation generation and/or innovation adoption, and propose a model of organizational culture and innovation generation and/or adoption.
Abstract: Crucial information barely visible to the human eye is
often embedded in a series of low resolution images taken of the
same scene. Super resolution reconstruction is the process of
combining several low resolution images into a single higher
resolution image. The ideal algorithm should be fast, and should add
sharpness and details, both at edges and in regions without adding
artifacts. In this paper we propose a super resolution blind
reconstruction technique for linearly degraded images. In our
proposed technique the algorithm is divided into three parts an image
registration, wavelets based fusion and an image restoration. In this
paper three low resolution images are considered which may sub
pixels shifted, rotated, blurred or noisy, the sub pixel shifted images
are registered using affine transformation model; A wavelet based
fusion is performed and the noise is removed using soft thresolding.
Our proposed technique reduces blocking artifacts and also
smoothens the edges and it is also able to restore high frequency
details in an image. Our technique is efficient and computationally
fast having clear perspective of real time implementation.
Abstract: IEEE has recently incorporated CCMP protocol to provide robust security to IEEE 802.11 wireless LANs. It is found that CCMP has been designed with a weak nonce construction and transmission mechanism, which leads to the exposure of initial counter value. This weak construction of nonce renders the protocol vulnerable to attacks by intruders. This paper presents how the initial counter can be pre-computed by the intruder. This vulnerability of counter block value leads to pre-computation attack on the counter mode encryption of CCMP. The failure of the counter mode will result in the collapse of the whole security mechanism of 802.11 WLAN.
Abstract: Transport and land use are two systems that are
mutually influenced. Their interaction is a complex process
associated with continuous feedback. The paper examines the
existing land use around an under construction metro station of the
new metro network of Thessaloniki, Greece, through the use of field
investigations, around the station-s predefined location. Moreover,
except from the analytical land use recording, a sampling
questionnaire survey is addressed to several selected enterprises of
the study area. The survey aims to specify the characteristics of the
enterprises, the trip patterns of their employees and clients, as well as
the stated preferences towards the changes the new metro station is
considered to bring to the area. The interpretation of the interrelationships
among selected data from the questionnaire survey takes
place using the method of Principal Components Analysis for
Categorical Data. The followed methodology and the survey-s results
contribute to the enrichment of the relevant bibliography concerning
the way the creation of a new metro station can have an impact on the
land use pattern of an area, by examining the situation before the
operation of the station.
Abstract: Concrete strength evaluated from compression tests
on cores is affected by several factors causing differences from the
in-situ strength at the location from which the core specimen was
extracted. Among the factors, there is the damage possibly occurring
during the drilling phase that generally leads to underestimate the
actual in-situ strength. In order to quantify this effect, in this study
two wide datasets have been examined, including: (i) about 500 core
specimens extracted from Reinforced Concrete existing structures,
and (ii) about 600 cube specimens taken during the construction of
new structures in the framework of routine acceptance control. The
two experimental datasets have been compared in terms of
compression strength and specific weight values, accounting for the
main factors affecting a concrete property, that is type and amount of
cement, aggregates' grading, type and maximum size of aggregates,
water/cement ratio, placing and curing modality, concrete age. The
results show that the magnitude of the strength reduction due to
drilling damage is strongly affected by the actual properties of
concrete, being inversely proportional to its strength. Therefore, the
application of a single value of the correction coefficient, as generally
suggested in the technical literature and in structural codes, appears
inappropriate. A set of values of the drilling damage coefficient is
suggested as a function of the strength obtained from compressive
tests on cores.
Abstract: In this study, a synthetic pathway was created by
assembling genes from Clostridium butyricum and Escherichia coli
in different combinations. Among the genes were dhaB1 and dhaB2
from C. butyricum VPI1718 coding for glycerol dehydratase (GDHt)
and its activator (GDHtAc), respectively, involved in the conversion
of glycerol to 3-hydroxypropionaldehyde (3-HPA). The yqhD gene
from E.coli BL21 was also included which codes for an NADPHdependent
1,3-propanediol oxidoreductase isoenzyme (PDORI)
reducing 3-HPA to 1,3-propanediol (1,3-PD). Molecular modeling
analysis indicated that the conformation of fusion protein of YQHD
and DHAB1 was favorable for direct molecular channeling of the
intermediate 3-HPA. According to the simulation results, the yqhD
and dhaB1 gene were assembled in the upstream of dhaB2 to express
a fusion protein, yielding the recombinant strain E. coliBL21
(DE3)//pET22b+::yqhD-dhaB1_dhaB2 (strain BP41Y3). Strain
BP41Y3 gave 10-fold higher 1,3-PD concentration than E. coliBL21
(DE3)//pET22b+::yqhD-dhaB1_dhaB2 (strain BP31Y2) expressing
the recombinant enzymes simultaneously but in a non-fusion mode.
This is the first report using a gene fusion approach to enhance the
biological conversion of glycerol to the value added compound 1,3-
PD.
Abstract: Sub-prime mortgage crisis which began in the US is
regarded as the most economic crisis since the Great Depression in the
early 20th century. Especially, hidden problems on efficient operation
of a business were disclosed at a time and many financial institutions
went bankrupt and filed for court receivership. The collapses of
physical market lead to bankruptcy of manufacturing and construction
businesses. This study is to analyze dynamic efficiency of construction
businesses during the five years at the turn of the global financial
crisis. By discovering the trend and stability of efficiency of a
construction business, this study-s objective is to improve
management efficiency of a construction business in the
ever-changing construction market. Variables were selected by
analyzing corporate information on top 20 construction businesses in
Korea and analyzed for static efficiency in 2008 and dynamic
efficiency between 2006 and 2010. Unlike other studies, this study
succeeded in deducing efficiency trend and stability of a construction
business for five years by using the DEA/Window model. Using the
analysis result, efficient and inefficient companies could be figured
out. In addition, relative efficiency among DMU was measured by
comparing the relationship between input and output variables of
construction businesses. This study can be used as a literature to
improve management efficiency for companies with low efficiency
based on efficiency analysis of construction businesses.
Abstract: In this article the accumulated results out of the effects
and length of the manufacture and production projects in the
university and research standard have been settled with the usefulness
definition of the process of project management for the accessibility
to the proportional pattern in the “time and action" stages. Studies
show that many problems confronted by the researchers in these
projects are connected to the non-profiting of: 1) autonomous timing
for gathering the educational theme, 2) autonomous timing for
planning and pattern, presenting before the construction, and 3)
autonomous timing for manufacture and sample presentation from the
output. The result of this study indicates the division of every
manufacture and production projects into three smaller autonomous
projects from its kind, budget and autonomous expenditure, shape
and order of the stages for the management of these kinds of projects.
In this case study real result are compared with theoretical results.
Abstract: This paper presents a ray tracing simulation technique for characterize the radiowave propagation inside building. The implementation of an algorithm capable of enumerating a large number of propagation paths in interactive time for the special case of 2.5D. The effective dielectric constants of the building structure in the simulations are indicated. The study describes an efficient 2.5D model of ray tracing algorithm were compared with 3D model. The result of the first investigations is that the environment of the indoor wave significantly changes as we change the electric parameters of material constructions. A detailed analysis of the dependence of the indoor wave on the wideband characteristics of the channel: root mean square (RMS) delay spread characteristics and Mean excess delay, is also investigated.
Abstract: The length of a cycle basis of a graph is the sum of the lengths of its elements. A minimum cycle basis is a cycle basis with minimum length. In this work, a construction of a minimum cycle basis for the wreath product of wheels with stars is presented. Moreover, the length of minimum cycle basis and the length of its longest cycle are calculated.
Abstract: Achieving success is a highly critical issue for the
companies to survive in a competitive business environment. The
construction industry is also an area where there is strong
competition due to a large number of construction contractors. There
have been many factors such as qualified employees, quality
workmanship and financial management that can lead to company
success in the construction industry. The aim of this study was to
investigate the critical factors leading to construction company
success. Within this context, a survey was carried out among 40
Turkish construction companies which are located in the Northwest
region of Turkey. In this survey, top-level managers and owners of
the companies were interviewed. The interviews took place over a
five month period between January and May 2007. Finally, the
ranking of the critical success factors has been determined by using
the Simple Multi Attribute Rating Technique (SMART). Based on
the results, business management, financial conditions and
owner/manager characteristics were determined as the most
important factors to company success.
Abstract: This paper proposes a modeling method of the laws controlling manufacturing systems with temporal and non temporal constraints. A methodology of robust control construction generating the margins of passive and active robustness is being elaborated. Indeed, two paramount models are presented in this paper. The first utilizes the P-time Petri Nets which is used to manage the flow type disturbances. The second, the quality model, exploits the Intervals Constrained Petri Nets (ICPN) tool which allows the system to preserve its quality specificities. The redundancy of the robustness of the elementary parameters between passive and active is also used. The final model built allows the correlation of temporal and non temporal criteria by putting two paramount models in interaction. To do so, a set of definitions and theorems are employed and affirmed by applicator examples.
Abstract: Construction site safety in China has aroused
comprehensive concern all over the world. It is imperative to
investigate the main causes of poor construction site safety. This paper
divides all the causes into four aspects, namely the factors of workers,
object, environment and management and sets up the accident causes
element system based on Delphi Method. This is followed by the
application of structural equation modeling to examine the importance
of each aspect of causes from the standpoints of different roles related
to the construction respectively. The results indicate that all the four
aspects of factors are in need of improvement, and different roles have
different ideas considering the priority of those factors. The paper has
instructive significance for the practitioners to take measures to
improve construction site safety in China accordingly.
Abstract: This paper describes the development of an
autonomous robot for painting the interior walls of buildings. The
robot consists of a painting arm with an end effector roller that scans
the walls vertically and a mobile platform to give horizontal feed to
paint the whole area of the wall. The painting arm has a planar twolink
mechanism with two joints. Joints are driven from a stepping
motor through a ball screw-nut mechanism. Four ultrasonic sensors
are attached to the mobile platform and used to maintain a certain
distance from the facing wall and to avoid collision with side walls.
When settled on adjusted distance from the wall, the controller starts
the painting process autonomously. Simplicity, relatively low weight
and short painting time were considered in our design. Different
modules constituting the robot have been separately tested then
integrated. Experiments have shown successfulness of the robot in its
intended tasks.