Abstract: This paper discusses the utilization of marine biomass as an energy resource in Japan. A marine biomass energy system in Japan was proposed consisting of seaweed cultivation (Laminaria japonica) at offshore marine farms, biogas production via methane fermentation of the seaweeds, and fuel cell power generation driven by the generated biogas. We estimated energy output, energy supply potential, and CO2 mitigation in Japan on the basis of the proposed system. As a result, annual energy production was estimated to be 1.02-109 kWh/yr at nine available sites. Total CO2 mitigation was estimated to be 1.04-106 tonnes per annum at the nine sites. However, the CO2 emission for the construction of relevant facilities is not taken into account in this paper. The estimated CO2 mitigation is equivalent to about 0.9% of the required CO2 mitigation for Japan per annum under the Kyoto Protocol framework.
Abstract: Blind signatures enable users to obtain valid signatures for a message without revealing its content to the signer. This paper presents a new blind signature scheme, i.e. identity-based blind signature scheme with message recovery. Due to the message recovery property, the new scheme requires less bandwidth than the identitybased blind signatures with similar constructions. The scheme is based on modified Weil/Tate pairings over elliptic curves, and thus requires smaller key sizes for the same level of security compared to previous approaches not utilizing bilinear pairings. Security and efficiency analysis for the scheme is provided in this paper.
Abstract: An attempt in this paper proposes a re-modification to
the minimum moment approach of resource leveling which is a modified minimum moment approach to the traditional method by
Harris. The method is based on critical path method. The new approach suggests the difference between the methods in the
selection criteria of activity which needs to be shifted for leveling resource histogram. In traditional method, the improvement factor
found first to select the activity for each possible day of shifting. In
modified method maximum value of the product of Resources Rate
and Free Float was found first and improvement factor is then
calculated for that activity which needs to be shifted. In the proposed
method the activity to be selected first for shifting is based on the largest value of resource rate. The process is repeated for all the
remaining activities for possible shifting to get updated histogram.
The proposed method significantly reduces the number of iterations
and is easier for manual computations.
Abstract: Nuclear matrix protein 22 (NMP22) is a FDA approved
biomarker for bladder cancer. The objective of this study is to develop
a simple NMP22 immumosensor (NMP22-IMS) for accurate
measurement of NMP22. The NMP22-IMS was constructed with
NMP22 antibody immobilized on screen-printed carbon electrodes.
The construction procedures and antibody immobilization are simple.
Results showed that the NMP22-IMS has an excellent (r2³0.95)
response range (20 – 100 ng/mL). In conclusion, a simple and reliable
NMP22-IMS was developed, capable of precisely determining urine
NMP22 level.
Abstract: Optical 3D measurement of objects is meaningful in
numerous industrial applications. In various cases shape acquisition
of weak textured objects is essential. Examples are repetition parts
made of plastic or ceramic such as housing parts or ceramic bottles as
well as agricultural products like tubers. These parts are often
conveyed in a wobbling way during the automated optical inspection.
Thus, conventional 3D shape acquisition methods like laser scanning
might fail. In this paper, a novel approach for acquiring 3D shape of
weak textured and moving objects is presented. To facilitate such
measurements an active stereo vision system with structured light is
proposed. The system consists of multiple camera pairs and auxiliary
laser pattern generators. It performs the shape acquisition within one
shot and is beneficial for rapid inspection tasks. An experimental
setup including hardware and software has been developed and
implemented.
Abstract: In recent years demolished concrete waste handling and management is the new primary challenging issue faced by the countries all over the world. It is very challenging and hectic problem that has to be tackled in an indigenous manner, it is desirable to completely recycle demolished concrete waste in order to protect natural resources and reduce environmental pollution. In this research paper an experimental study is carried out to investigate the feasibility and recycling of demolished waste concrete for new construction. The present investigation to be focused on recycling demolished waste materials in order to reduce construction cost and resolving housing problems faced by the low income communities of the world. The crushed demolished concrete wastes is segregated by sieving to obtain required sizes of aggregate, several tests were conducted to determine the aggregate properties before recycling it into new concrete. This research shows that the recycled aggregate that are obtained from site make good quality concrete. The compressive strength test results of partial replacement and full recycled aggregate concrete and are found to be higher than the compressive strength of normal concrete with new aggregate.
Abstract: Aluminothermic rail welding was from the beginning
a great success because its low price even in 1895 in Germany. This
method is now, widely used all over the world for the railways
construction, maintenance and modernization. Instructions give you
guidelines for preparing papers for conferences or journals.
After 1989, the welding needs of the potentials beneficiaries
(Romanian Railways, Urban Transportation Companies) keep raise
because of the railways maintenance and modernization necessity.
The main materials that determine the Thermit (T) composition
result from manufacturing scraps all over the country. This can help
the environment by consuming these scraps.
The Romanian need for alumino-thermic welding is now by 11300
per year, and in a favourable economical environment, this amount
can reach 30000 units.
This paper tries to show the effect of two types of modifiers
introduced in the T composition on the structure and properties of an
alumino-thermic welding.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: Key performance indicators (KPIs) are used for post
result evaluation in the construction industry, and they normally do
not have provisions for changes. This paper proposes a set of
dynamic key performance indicators (d-KPIs) which predicts the
future performance of the activity being measured and presents the
opportunity to change practice accordingly. Critical to the
predictability of a construction project is the ability to achieve
automated data collection. This paper proposes an effective way to
collect the process and engineering management data from an
integrated construction management system. The d-KPI matrix,
consisting of various indicators under seven categories, developed
from this study can be applied to close monitoring of the
development projects of aged-care facilities. The d-KPI matrix also
enables performance measurement and comparison at both project
and organization levels.
Abstract: Construction delay is unavoidable in developing
countries including Malaysia. It is defined as time overrun or
extension of time for completion of a project. The purpose of the
study is to determine the causes of delay in Malaysian construction
industries based on previous worldwide research. The field survey
conducted includes the experienced developers, consultants and
contractors in Malaysia. 34 causes of the construction delay have
been determined and 24 have been selected using the Rasch model
analysis. The analysis result will be used as the baseline for the next
research to find the causes of delay in the Malaysian construction
industry taking place in Malaysian higher learning institutions.
Abstract: This work presents an approach for the construction of a hybrid color-texture space by using mutual information. Feature extraction is done by the Laws filter with SVM (Support Vectors Machine) as a classifier. The classification is applied on the VisTex database and a SPOT HRV (XS) image representing two forest areas in the region of Rabat in Morocco. The result of classification obtained in the hybrid space is compared with the one obtained in the RGB color space.
Abstract: With optimized bandwidth and latency discrepancy ratios, Node Gain Scores (NGSs) are determined and used as a basis for shaping the max-heap overlay. The NGSs - determined as the respective bandwidth-latency-products - govern the construction of max-heap-form overlays. Each NGS is earned as a synergy of discrepancy ratio of the bandwidth requested with respect to the estimated available bandwidth, and latency discrepancy ratio between the nodes and the source node. The tree leads to enhanceddelivery overlay multicasting – increasing packet delivery which could, otherwise, be hindered by induced packet loss occurring in other schemes not considering the synergy of these parameters on placing the nodes on the overlays. The NGS is a function of four main parameters – estimated available bandwidth, Ba; individual node's requested bandwidth, Br; proposed node latency to its prospective parent (Lp); and suggested best latency as advised by source node (Lb). Bandwidth discrepancy ratio (BDR) and latency discrepancy ratio (LDR) carry weights of α and (1,000 - α ) , respectively, with arbitrary chosen α ranging between 0 and 1,000 to ensure that the NGS values, used as node IDs, maintain a good possibility of uniqueness and balance between the most critical factor between the BDR and the LDR. A max-heap-form tree is constructed with assumption that all nodes possess NGS less than the source node. To maintain a sense of load balance, children of each level's siblings are evenly distributed such that a node can not accept a second child, and so on, until all its siblings able to do so, have already acquired the same number of children. That is so logically done from left to right in a conceptual overlay tree. The records of the pair-wise approximate available bandwidths as measured by a pathChirp scheme at individual nodes are maintained. Evaluation measures as compared to other schemes – Bandwidth Aware multicaSt architecturE (BASE), Tree Building Control Protocol (TBCP), and Host Multicast Tree Protocol (HMTP) - have been conducted. This new scheme generally performs better in terms of trade-off between packet delivery ratio; link stress; control overhead; and end-to-end delays.
Abstract: The Taiwan government has invested approximately
21 billion NT dollars in the construction of bicycle paths since
bicycling has gained huge popularity as a healthy leisure and
recreational activity. This study focuses on the behavior of
recreational bicyclists in Danshuei and Bali, northern Taiwan. Data
were collected from a field investigation carried out along the
Danshuei bicycle path and Bali left-bank bicycle path. A total of 578
questionnaires were gathered for data analysis. Descriptive statistics
and Chi-Square tests were used to assess bicyclists- behaviors. The
frequency shows that, in these areas, Danshuei and Bali, most
bicyclists rented bicycles, rode the bicycle path in the afternoon for
about 2 hours. The used the bicycle path one time per week. For most,
it was the first time to ride these bicycle paths. There were significant
differences in distribution of bicycle ownership, time of day, duration
of ride, ride frequency, and whether riding occurred on weekdays or
weekends. Results indicated that most bicyclists in Danshuei and Bali
were infrequent users.
Abstract: This paper describes a system, in which various methods of text summarizing can be adapted to Polish. A structure of the system is presented. A modular construction of the system and access to the system via the Internet are signaled.
Abstract: Few studies have been conducted on polymeric strip
and the behavior of soil retaining walls. This paper will present the
effect of frequency on the dynamic behavior of reinforced soil
retaining walls with polymeric strips. The frequency content
describes how the amplitude of a ground motion is distributed among
different frequencies. Since the frequency content of an earthquake
motion will strongly influence the effects of that motion, the
characterization of the motion cannot be completed without the
consideration of its frequency content. The maximum axial force of
reinforcements and horizontal displacement of the reinforced walls
are focused in this research. To clarify the dynamic behavior of
reinforced soil retaining walls with polymeric strips, a numerical
modeling using Finite Difference Method is benefited. As the results
indicate, the frequency of input base acceleration has an important
effect on the behavior of these structures. Because of resonant in the
system, where the frequency of the input dynamic load is equal to the
natural frequency of the system, the maximum horizontal
displacement and the maximum axial forces in polymeric strips is
occurred. Moreover, they were to increase the structure flexibility
because of the main advantages of polymeric strips; i.e. being simple
method of construction, having a homogeneous behavior with soils,
and possessing long durability, which are of great importance in
dynamic analysis.
Abstract: Object-oriented simulation is considered one of the most sophisticated techniques that has been widely used in planning, designing, executing and maintaining construction projects. This technique enables the modeler to focus on objects which is extremely important for thorough understanding of a system. Thus, identifying an object is an essential point of building a successful simulation model. In a maintenance process an object is a maintenance work order (MWO). This study demonstrates a maintenance simulation model for the building maintenance division of Saudi Consolidated Electric Company (SCECO) in Dammam, Saudi Arabia. The model focused on both types of maintenance processes namely: (1) preventive maintenance (PM) and (2) corrective maintenance (CM). It is apparent from the findings that object-oriented simulation is a good diagnostic and experimental tool. This is because problems, limitations, bottlenecks and so forth are easily identified. These features are very difficult to obtain when using other tools.
Abstract: The area of Project Risk Management (PRM) has
been extensively researched, and the utilization of various tools and
techniques for managing risk in several industries has been
sufficiently reported. Formal and systematic PRM practices have
been made available for the construction industry. Based on such
body of knowledge, this paper tries to find out the global picture of
PRM practices and approaches with the help of a survey to look into
the usage of PRM techniques and diffusion of software tools, their
level of maturity, and their usefulness in the construction sector.
Results show that, despite existing techniques and tools, their usage is
limited: software tools are used only by a minority of respondents
and their cost is one of the largest hurdles in adoption. Finally, the
paper provides some important guidelines for future research
regarding quantitative risk analysis techniques and suggestions for
PRM software tools development and improvement.
Abstract: A self-compacting concrete (SCC) is the one that can
be placed in the form and can go through obstructions by its own
weight and without the need of vibration. Since its first development
in Japan in 1988, SCC has gained wider acceptance in Japan, Europe
and USA due to its inherent distinct advantages. Although there are
visible signs of its gradual acceptance in the North Africa through its
limited use in construction, Libya has yet to explore the feasibility
and applicability of SCC in new construction. The contributing
factors to this reluctance appear to be lack of any supportive
evidence of its suitability with local aggregates and the harsh
environmental conditions. The primary aim of this study is to explore
the feasibility of using SCC made with local aggregates of Eastern
Province of Libya by examining its basic properties characteristics.
This research consists of: (i) Development of a suitable mix for SCC
such as the effect of water to cement ratio, limestone and silica fume
that would satisfy the requirements of the plastic state; (ii) Casting of
concrete samples and testing them for compressive strength and unit
weight. Local aggregates, cement, admixtures and industrial waste
materials were used in this research.
The significance of this research lies in its attempt to provide
some performance data of SCC made in the Eastern Province of
Libya so as to draw attention to the possible use of SCC.
Abstract: Optimal cultural site selection is one of the ways that
can lead to the promotion of citizenship culture in addition to
ensuring the health and leisure of city residents. This study examines
the social and cultural needs of the community and optimal cultural
site allocation and after identifying the problems and shortcomings,
provides a suitable model for finding the best location for these
centers where there is the greatest impact on the promotion of
citizenship culture. On the other hand, non-scientific methods cause
irreversible impacts to the urban environment and citizens. But
modern efficient methods can reduce these impacts. One of these
methods is using geographical information systems (GIS). In this
study, Analytical Hierarchy Process (AHP) method was used to
locate the optimal cultural site. In AHP, three principles
(decomposition), (comparative analysis), and (combining
preferences) are used. The objectives of this research include
providing optimal contexts for passing time and performing cultural
activities by Shiraz residents and also proposing construction of some
cultural sites in different areas of the city. The results of this study
show the correct positioning of cultural sites based on social needs of
citizens. Thus, considering the population parameters and radii
access, GIS and AHP model for locating cultural centers can meet
social needs of citizens.
Abstract: As the resources for naturally occurring aggregates
diminished at an ever increasing rate, researchers are keen to utilize
recycled materials in road construction in harmony with sustainable
development. Steel slag, a waste product from the steel making
industry, is one of the recycled materials reported to exhibit great
potential to replace naturally occurring aggregates in asphalt
mixtures. This paper presents the resilient modulus properties of
steel slag asphalt mixtures subjected to short term oven ageing
(STOA). The resilient modulus test was carried out to evaluate the
stiffness of asphalt mixtures at 10ºC, 25ºC and 40ºC. Previous
studies showed that stiffness changes in asphalt mixture played an
important role in inflicting pavement distress particularly cracking
and rutting that are common at low and high temperatures
respectively. Temperature was found to significantly influence the
resilient modulus of asphalt mixes. The resilient modulus of the
asphalt specimens tested decreased by more than 90% when the test
temperature increased from 10°C to 40°C.