Abstract: Unstructured peer-to-peer networks are popular due to
its robustness and scalability. Query schemes that are being used in
unstructured peer-to-peer such as the flooding and interest-based
shortcuts suffer various problems such as using large communication
overhead long delay response. The use of routing indices has been a
popular approach for peer-to-peer query routing. It helps the query
routing processes to learn the routing based on the feedbacks
collected. In an unstructured network where there is no global
information available, efficient and low cost routing approach is
needed for routing efficiency.
In this paper, we propose a novel mechanism for query-feedback
oriented routing indices to achieve routing efficiency in unstructured
network at a minimal cost. The approach also applied information
retrieval technique to make sure the content of the query is
understandable and will make the routing process not just based to
the query hits but also related to the query content. Experiments have
shown that the proposed mechanism performs more efficient than
flood-based routing.
Abstract: The pyrolysis characteristics and kinetics of seven marine biomass, which are fixed Enteromorpha clathrata, floating Enteromorpha clathrata, Ulva lactuca L., Zosterae Marinae L., Thallus Laminariae, Asparagus schoberioides kunth and Undaria pinnatifida (Harv.), were studied with thermogravimetric analysis method. Simultaneously, cornstalk, which is a grass biomass, and sawdust, which is a lignocellulosic biomass, were references. The basic pyrolysis characteristics were studied by using TG- DTG-DTA curves. The results showed that there were three stages (dehydration, dramatic weight loss and slow weight loss) during the whole pyrolysis process of samples. The Tmax of marine biomass was significantly lower than two kinds of terrestrial biomass. Zosterae Marinae L. had a relatively high stability of pyrolysis, but floating Enteromorpha clathrata had lowest stability of pyrolysis and a good combustion characteristics. The corresponding activation energy E and frequency factor A were obtained by Coats-Redfern method. It was found that the pyrolysis reaction mechanism functions of three kinds of biomass are different.
Abstract: This comparison of valuation techniques for bone age
assessment is a work carried out by the Telemedicine Research Group
of the Military University - TIGUM, as a preliminary to the Design
and development a treatment system of hand and wrist radiological
images for children aged 0-6 years to bone age assessment . In this
paper the techniques mentioned for decades have been the most
widely used and the statistically significant.
Althought, initially with the current project, it wants to work with
children who have limit age, this comparison and evaluation
techniques work will help in the future to expand the study subject in
the system to bone age assessment, implementing more techniques,
tools and deeper analysis to accomplish this purpose.
Abstract: Capacity and efficiency of any refrigerating system
diminish rapidly as the difference between the evaporating and
condensing temperature is increased by reduction in the evaporator
temperature. The single stage vapour compression refrigeration
system is limited to an evaporator temperature of -40 0C. Below
temperature of -40 0C the either cascade refrigeration system or multi
stage vapour compression system is employed. Present work
describes thermal design of main three heat exchangers namely
condenser (HTS), cascade condenser and evaporator (LTS) of
R404A-R508B and R410A-R23 cascade refrigeration system. Heat
transfer area of condenser (HTS), cascade condenser and evaporator
(LTS) for both systems have been compared and the effect of
condensing and evaporating temperature on heat-transfer area for
both systems have been studied under same operating condition. The
results shows that the required heat-transfer area of condenser and
cascade condenser for R410A-R23 cascade system is lower than the
R404A-R508B cascade system but heat transfer area of evaporator is
similar for both the system. The heat transfer area of condenser and
cascade condenser decreases with increase in condensing temperature
(Tc), whereas the heat transfer area of cascade condenser and
evaporator increases with increase in evaporating temperature (Te).
Abstract: The bridge vibration due to traffic loading has been a
subject of extensive research during the last decades. A number of
these studies are concerned with the effects of the unevenness of
roadways on the dynamic responses of highway bridges. The road
unevenness is often described as a random process that constitutes
of different wavelengths. Thus, the study focuses on examining
the effects of the random description of roadways on the dynamic
response and its variance. A new setting of variance based sensitivity
analysis is proposed and used to identify and quantify the
contributions of the roadway-s wavelengths to the variance of the
dynamic response. Furthermore, the effect of the vehicle-s speed on
the dynamic response is studied.
Abstract: A new and highly efficient architecture for elliptic curve scalar point multiplication which is optimized for a binary field recommended by NIST and is well-suited for elliptic curve cryptographic (ECC) applications is presented. To achieve the maximum architectural and timing improvements we have reorganized and reordered the critical path of the Lopez-Dahab scalar point multiplication architecture such that logic structures are implemented in parallel and operations in the critical path are diverted to noncritical paths. With G=41, the proposed design is capable of performing a field multiplication over the extension field with degree 163 in 11.92 s with the maximum achievable frequency of 251 MHz on Xilinx Virtex-4 (XC4VLX200) while 22% of the chip area is occupied, where G is the digit size of the underlying digit-serial finite field multiplier.
Abstract: As the world changes more rapidly, the demand for update information for resource management, environment monitoring, planning are increasing exponentially. Integration of Remote Sensing with GIS technology will significantly promote the ability for addressing these concerns. This paper presents an alternative way of update GIS applications using image processing and high resolution images. We show a method of high-resolution image segmentation using graphs and morphological operations, where a preprocessing step (watershed operation) is required. A morphological process is then applied using the opening and closing operations. After this segmentation we can extract significant cartographic elements such as urban areas, streets or green areas. The result of this segmentation and this extraction is then used to update GIS applications. Some examples are shown using aerial photography.
Abstract: Several optimization algorithms specifically applied to
the problem of Operation Planning of Hydrothermal Power Systems
have been developed and are used. Although providing solutions to
various problems encountered, these algorithms have some
weaknesses, difficulties in convergence, simplification of the original
formulation of the problem, or owing to the complexity of the
objective function. Thus, this paper presents the development of a
computational tool for solving optimization problem identified and to
provide the User an easy handling. Adopted as intelligent
optimization technique, Genetic Algorithms and programming
language Java. First made the modeling of the chromosomes, then
implemented the function assessment of the problem and the
operators involved, and finally the drafting of the graphical interfaces
for access to the User. The program has managed to relate a coherent
performance in problem resolution without the need for
simplification of the calculations together with the ease of
manipulating the parameters of simulation and visualization of output
results.
Abstract: Foodborne Salmonella infections have become a
major problem world wide. Salmonellosis transmitted from fish are
quite common. Established quality control measures exist for export
oriented fish, none exists for fish consumed locally. This study aimed
at characterization of Salmonella isolated from Nile tilapia . The
study was carried out in selected beaches along L. Victoria in
Western Kenya between March and June 2007. One hundred and
twenty fish specimens were collected. Salmonella isolates were
confirmed using serotyping, biochemical testing in addition to malic
acid dehydrogenase (mdh) and fliC gene sequencing. Twenty
Salmonella isolates were confirmed by mdh gene sequencing. Nine
(9) were S. enterica serotype typhimurium, four (4) were S. enterica
Serotype, enteritidis and seven (7) were S. enterica serotype typhi.
Nile tilapia have a role in transmission of Salmonellosis in the study
area, poor sanitation was a major cause of pollution at the beach
inshore waters.
Abstract: Globalisation is a phenomenon that cannot be avoided.
As globalisation allowed free flow of inputs including labour, it may
affect job opportunities for the locals. Therefore, investigate the
determinants of labour supply is essential in understanding the
structure of labour market in the new era of globalization. The
objective of this article is to examine labour supply by taking into
account the globalisation effect. The study covers 3885 households in
Peninsular Malaysia who are chosen using stratified random
sampling. The labour supply model will be the basis for the analysis.
The basic labour supply determinants are own wage and non-labour
income. However, the extended labour supply model incorporates
other variables like spouse wage，number of children and
individuals characteristics like education level and age. Besides, the
globalization indicator will also be incorporated as another
independent variable.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: One of the important steps in a safety and risk management system is the economical evaluation of occupational accident and diseases costs in order to decrease accidents from reoccurring in the workplace. This study proposed a plausible method for calculating occupational accident costs and illnesses in work place. This method design for cost estimation takes into account both the personnel, organizational level as well as the community level especially intended for an Iranian work place. The research indicates that a using systematic method for calculating costs which also provides risk evaluation can help managers to plan correctly the investment in health and safety measures. Using this method is that not only is it comprehensive, easy and practical and could be applied in practice by a manager within a short period of time but it also shows the importance of accident costs as well as calculates the real cost of an accident and illnesses.
Abstract: The paper presents the service learning project titled
DicDucFac (idea-leadership-product), that was planned and
conducted by the team of information sciences students. It was
planned as a workshop dealing with the application of modern social
media (Facebook, YouTube, Gmail) for the purposes of selfpromotion,
free advertising via social networks and marketing own
ideas and/or products in the virtual world. The workshop was
organized for highly-skilled computer literate unemployed youth.
These youth, as final beneficiaries, will be able to apply what they
learned in this workshop to “the real world“, increasing their chances
for employment and self-employment. The results of the project
reveal that the basic, active-learning principles embodied in our
teaching approach allow students to learn more effectively and gain
essential life skills (from computer applications to teamwork) that
can only be learned by doing. It also shows that our students received
the essentials of professional ethics and citizenship through direct,
personal engagement in professional activities and the life of the
community.
Abstract: In this paper, we research the standard 13-point difference schemes for solving the biharmonic equation. Heuristic method is applied to judging the stability of multi-level difference schemes of the biharmonic equation. It is showed that the standard 13-point difference schemes are stable.
Abstract: This paper, a simple continuous conduction mode (CCM) pulse-width-modulated (PWM) controller for high power factor boost converters is introduced. The duty ratios were obtained by the comparison of a sensed signal from inductor current or switch current and a negative slope ramp carrier waveform in each switching period. Due to the proposed control requires only the inductor current or switch current sensor and the output voltage sensor, its circuit implementation was very simple. To verify the proposed control, the circuit experimentation of a 350 W boost converter with the proposed control was applied. From the results, the input current waveform was shaped to be closely sinusoidal, implying high power factor and low harmonics.
Abstract: In an electric power system, spinning reserve
requirements can be determined by using deterministic and/or
probabilistic measures. Although deterministic methods are usual in
many systems, application of probabilistic methods becomes
increasingly important in the new environment of the electric power
utility industry. This is because of the increased uncertainty
associated with competition. In this paper 1) a new probabilistic
method is presented which considers the reliability of transmission
system in a simplified manner and 2) deterministic and probabilistic
methods are compared. The studied methods are applied to the Roy
Billinton Test System (RBTS).
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Transient Stability is an important issue in power systems planning, operation and extension. The objective of transient stability analysis problem is not satisfied with mere transient instability detection or evaluation and it is most important to complement it by defining fast and efficient control measures in order to ensure system security. This paper presents a new Fuzzy Support Vector Machines (FSVM) to investigate the stability status of power systems and a modified generation rescheduling scheme to bring back the identified unstable cases to a more economical and stable operating point. FSVM improves the traditional SVM (Support Vector Machines) by adding fuzzy membership to each training sample to indicate the degree of membership of this sample to different classes. The preventive control based on economic generator rescheduling avoids the instability of the power systems with minimum change in operating cost under disturbed conditions. Numerical results on the New England 39 bus test system show the effectiveness of the proposed method.
Abstract: Hospitals in southern Hualien teamed with the
Hypertension Joint Care Network. Working with the network, the
team provided a special designed health education to the individual
who had been identified as a hypertension patient in the outpatient
department. Some metabolism improvements achieved. This is a
retrospective study by purposively taking 106 patients from a hospital
between 2008 and 2010. Records of before and after education
intervention of the objects was collected and analyzed to see the how
the intervention affected the patients- hypertension control via clinical
parameter monitoring. The results showed that the clinical indicators,
the LDL-C, the cholesterol and the systolic blood pressure were
significantly improved. The study provides evidence for the
effectiveness of the network in controlling hypertension.