Abstract: In this research, the laminar heat transfer of natural convection on vertical surfaces has been investigated. Most of the studies on natural convection have been considered constantly whereas velocity and temperature domain, do not change with time, transient one are used a lot. Governing equations are solved using a finite volume approach. The convective terms are discretized using the power-law scheme, whereas for diffusive terms the central difference is employed. Coupling between the velocity and pressure is made with SIMPLE algorithm. The resultant system of discretized linear algebraic equations is solved with an alternating direction implicit scheme. Then a configuration of rectangular fins is put in different ways on the surface and heat transfer of natural convection on these surfaces without sliding is studied and finally optimization is done.
Abstract: In this paper, the thermo-electro-structural coupledfield
in a cracked metal plate is studied using the finite element
analysis. From the computational results, the compressive stresses
reveal near the crack tip. This conclusion agrees with the past
reference. Furthermore, the compressive condition can retard and stop
the crack growth during the Joule heating process.
Abstract: This paper presents a comparative study on
Vanadyl Phthalocyanine (VOPc) thin films deposited by thermal
evaporation and spin coating techniques. The samples
were prepared on cleaned glass substrates and annealed at
various temperatures ranging form 95oC to 155oC. To obtain
the morphological and structural properties of VOPc thin
films, X-ray diffraction (XRD) technique and atomic force
microscopy (AFM) have been implied. The AFM topographic
images show a very slight difference in the thermally grown
films, before and after annealing, however best results are
achieved for the spin-cast film annealed at 125oC. The XRD
spectra show no existence of the sharp peaks, suggesting the
material to be amorphous. The humps in the XRD patterns
indicate the presence of some crystallites.
Abstract: The temperature distribution and the heat transfer
rates through a multi-layer door of a furnace were investigated. The
inside of the door was in contact with hot air and the other side of the
door was in contact with room air. Radiation heat transfer from the
walls of the furnace to the door and the door to the surrounding area
was included in the problem. This work is a two dimensional steady
state problem. The Churchill and Chu correlation was used to find
local convection heat transfer coefficients at the surfaces of the
furnace door. The thermophysical properties of air were the functions
of the temperatures. Polynomial curve fitting for the fluid properties
were carried out. Finite difference method was used to discretize for
conduction heat transfer within the furnace door. The Gauss-Seidel
Iteration was employed to compute the temperature distribution in
the door.
The temperature distribution in the horizontal mid plane of the
furnace door in a two dimensional problem agrees with the one
dimensional problem. The local convection heat transfer coefficients
at the inside and outside surfaces of the furnace door are exhibited.
Abstract: A wireless power transfer system can attribute to the
fields in robot, aviation and space in which lightening the weight of
device and improving the movement play an important role. A
wireless power transfer system was investigated to overcome the
inconvenience of using power cable. Especially a wireless power
transfer technology is important element for mobile robots. We
proposed the wireless power transfer system of the half-bridge
resonant converter with the frequency tracking and optimized
power transfer control unit. And the possibility of the application
and development system was verified through the experiment with
LED loads.
Abstract: Component-Based software engineering provides an
opportunity for better quality and increased productivity in software
development by using reusable software components [10]. One of the
most critical aspects of the quality of a software system is its
performance. The systematic application of software performance
engineering techniques throughout the development process can help
to identify design alternatives that preserve desirable qualities such
as extensibility and reusability while meeting performance objectives
[1]. In the present scenario, software engineering methodologies
strongly focus on the functionality of the system, while applying a
“fix- it-later" approach to software performance aspects [3]. As a
result, lengthy fine-tunings, expensive extra hard ware, or even
redesigns are necessary for the system to meet the performance
requirements. In this paper, we propose design based,
implementation independent, performance prediction approach to
reduce the overhead associated in the later phases while developing a
performance guaranteed software product with the help of Unified
Modeling Language (UML).
Abstract: This research analyzes factors affecting the success of
Litecoin Value within Thailand and develops a guideline for selfreliance
for effective business implementation. Samples in this study
included 119 people through surveys. The results revealed four main
factors affecting the success as follows: 1) Future Career training
should be pursued in applied Litecoin development. 2) Didn't grasp
the concept of a digital currency or see the benefit of a digital
currency. 3) There is a great need to educate the next generation of
learners on the benefits of Litecoin within the community. 4) A great
majority didn't know what Litecoin was.
The guideline for self-reliance planning consisted of 4 aspects: 1)
Development planning: by arranging meet up groups to conduct
further education on Litecoin and share solutions on adoption into
every day usage. Local communities need to develop awareness of
the usefulness of Litecoin and share the value of Litecoin among
friends and family. 2) Computer Science and Business Management
staff should develop skills to expand on the benefits of Litecoin
within their departments. 3) Further research should be pursued on
how Litecoin Value can improve business and tourism within
Thailand. 4) Local communities should focus on developing Litecoin
awareness by encouraging street vendors to accept Litecoin as
another form of payment for services rendered.
Abstract: Sign language is used by the deaf and hard of hearing people for communication. Automatic sign language recognition is a challenging research area since sign language often is the only way of communication for the deaf people. Sign language includes different components of visual actions made by the signer using the hands, the face, and the torso, to convey his/her meaning. To use different aspects of signs, we combine the different groups of features which have been extracted from the image frames recorded directly by a stationary camera. We combine the features in two levels by employing three techniques. At the feature level, an early feature combination can be performed by concatenating and weighting different feature groups, or by concatenating feature groups over time and using LDA to choose the most discriminant elements. At the model level, a late fusion of differently trained models can be carried out by a log-linear model combination. In this paper, we investigate these three combination techniques in an automatic sign language recognition system and show that the recognition rate can be significantly improved.
Abstract: To investigate the production of cellulases from Aspergillus heteromorphus, submerged fermentation was performed using wheat straw as substrate. Optimization of saccharification conditions like pH, temperature and time were studied. Highest reducing sugar was released on 5th day at 5 pH, 30° C temperature. When A. heteromorphous was grown on wheat straw in submerged fermentation after 5 days incubation at 30 ° C, 3.2 IU/ml and 83 IU/ml, filter paper activity and CMCase activity respectively.
Abstract: We construct an exponentially weighted Legendre- Gauss Tau method for solving differential equations with oscillatory solutions. The proposed method is applied to Sturm-Liouville problems. Numerical examples illustrating the efficiency and the high accuracy of our results are presented.
Abstract: In the present work, a comparative study on the
microstructure and mechanical properties of as cast, cast aged and
forged aged A356 alloy has been investigated. The study reveals that
mechanical properties of A356 alloy are highly influenced by melt
treatment and solid state processing. Cast aged alloys achieve highest
strength and hardness compared to as cast and forge aged ones. Ones
treated with combined addition of grain refiners and modifiers
achieve maximum strength and hardness. Cast aged A356 alloy
possesses higher wear resistance compared to as cast and forge aged
ones. Forging improves both strength and ductility of alloys over as
cast ones. However, the improvement in ductility is perceptible only
for properly grain refined and modified alloys. Ones refined with
0.65% Al-3Ti shows highest improvement in ductility while ones
treated with 0.20% Al-10Sr exhibits less improvement in ductility.
Abstract: Hydraulic conductivity is one parameter important for predicting the movement of water and contaminants dissolved in the water through the soil. The hydraulic conductivity is measured on soil samples in the lab and sometimes tests carried out in the field. The hydraulic conductivity has been related to soil particle diameter by a number of investigators. In this study, 25 set of soil samples with sand texture. The results show approximately success in predicting hydraulic conductivity from particle diameters data. The following relationship obtained from multiple linear regressions on data (R2 = 0.52): Where d10, d50 and d60, are the soil particle diameter (mm) that 10%, 50% and 60% of all soil particles are finer (smaller) by weight and Ks, saturated hydraulic conductivity is expressed in m/day. The results of regression analysis showed that d10 play a more significant role with respect to Ks, saturated hydraulic conductivity (m/day), and has been named as the effective parameter in Ks calculation.
Abstract: In this paper, an attempt has been made to obtain nonsensitive
solutions in the multi-objective optimization of a
photovoltaic/thermal (PV/T) air collector. The selected objective
functions are overall energy efficiency and exergy efficiency.
Improved thermal, electrical and exergy models are used to calculate
the thermal and electrical parameters, overall energy efficiency,
exergy components and exergy efficiency of a typical PV/T air
collector. A computer simulation program is also developed. The
results of numerical simulation are in good agreement with the
experimental measurements noted in the previous literature. Finally,
multi-objective optimization has been carried out under given
climatic, operating and design parameters. The optimized ranges of
inlet air velocity, duct depth and the objective functions in optimal
Pareto front have been obtained. Furthermore, non-sensitive solutions
from energy or exergy point of view in the results of multi-objective
optimization have been shown.
Abstract: The main idea behind in network aggregation is that,
rather than sending individual data items from sensors to sinks,
multiple data items are aggregated as they are forwarded by the
sensor network. Existing sensor network data aggregation techniques
assume that the nodes are preprogrammed and send data to a central
sink for offline querying and analysis. This approach faces two major
drawbacks. First, the system behavior is preprogrammed and cannot
be modified on the fly. Second, the increased energy wastage due to
the communication overhead will result in decreasing the overall
system lifetime. Thus, energy conservation is of prime consideration
in sensor network protocols in order to maximize the network-s
operational lifetime. In this paper, we give an energy efficient
approach to query processing by implementing new optimization
techniques applied to in-network aggregation. We first discuss earlier
approaches in sensors data management and highlight their
disadvantages. We then present our approach “Energy Efficient
Indexed Aggregation" (EEIA) and evaluate it through several
simulations to prove its efficiency, competence and effectiveness.
Abstract: Construction projects can be implemented under various contractual and organizational systems. They can be divided into two groups: systems without the managing company where the Client manages the process, and systems with the managing company, where management is entrusted to an external company. In the public sector of the Polish market there are two ways of delivery of construction projects with the participation of the manager: one is to assign operations to another party, the so called Project Supervisor, whilst the other results from the application of FIDIC conditions of contract, which entail appointment of the Engineer. The decision is to be made by the Client and depends on various factors. On the public procurement market in Poland the selection of construction project manager boils down to awarding the contract for such a service. The selection can be done by one of eight public procurement procedures identified by the procurement law. The paper provides the analysis of 96 contracts for services awarded in 2011, which employed construction management. The study aimed to investigate the methods and criteria for selecting managers, applied in practice by the Polish public Clients.
Abstract: Using DNA microarrays the comparative analysis of a
gene expression profiles is carried out in a liver and kidneys of pigs.
The hypothesis of a cross hybridization of one probe with different
cDNA sites of the same gene or different genes is checked up, and it
is shown, that cross hybridization can be a source of essential errors
at revealing of a key genes in organ-specific transcriptome. It is
reveald that distinctions in profiles of a gene expression are well coordinated
with function, morphology, biochemistry and histology of
these organs.
Abstract: A computational study at the level density functional theory (DFT) was carried out to investigate the influences of Si and C-doping on the 14N and 27Al quadrupole coupling constant in the (10, 0) zigzag single ? walled Aluminum-Nitride nanotube (AlNNT). To this aim, a 1.16nm, length of AlNNT consisting of 40 Al atoms and 40 N atoms were selected where the end atoms are capped by hydrogen atom. To follow the purpose, three Si atoms and three C atoms were doped instead of three Al atoms and three N atoms as a central ring in the surface of the Si and C-doped AlNNT. At first both of systems optimized at the level of BLYP method and 6-31G (d) basis set and after that, the NQR parameters were calculated at the level BLYP method and 6-311+G** basis set in two optimized forms. The calculate CQ values for both optimized AlNNT systems, raw and Si and C-doped, reveal different electronic environments in the mentioned systems. It was also demonstrated that the end nuclei have the largest CQ values in both considered AlNNT systems. All the calculations were carried out using Gaussian 98 package of program.
Abstract: Successful intelligence (SI) is the integrated set of the
ability needed to attain success in life, within individual-s sociocultural
context. People are successfully intelligent by recognizing
their strengths and weaknesses. They will find ways to strengthen
their weakness and maintain their strength or even improve it. SI
people can shape, select, and adapt to the environments by using
balance of higher-ordered thinking abilities including; critical,
creative, and applicative. Aims: The purposes of this study were to;
1) develop curriculum that promotes SI for nursing students, and 2)
study the effectiveness of the curriculum development. Method:
Research and Development was a method used for this study. The
design was divided into two phases; 1) the curriculum development
which composed of three steps (needs assessment, curriculum
development and curriculum field trail), and 2) the curriculum
implementation. In this phase, a pre-experimental research design
(one group pretest-posttest design) was conducted. The sample
composed of 49 sophomore nursing students of Boromarajonani
College of Nursing, Surin, Thailand who enrolled in Nursing care of
Health problem course I in 2011 academic year. Data were carefully
collected using 4 instruments; 1) Modified essay questions test
(MEQ) 2) Nursing Care Plan evaluation form 3) Group processing
observation form (α = 0.74) and 4) Satisfied evaluation form of
learning (α = 0.82). Data were analyzed using descriptive statistics
and content analysis. Results: The results revealed that the sample
had post-test average score of SI higher than pre-test average score
(mean difference was 5.03, S.D. = 2.84). Fifty seven percentages of
the sample passed the MEQ posttest at the criteria of 60 percentages.
Students demonstrated the strategies of how to develop nursing care
plan. Overall, students- satisfaction on teaching performance was at
high level (mean = 4.35, S.D. = 0.46). Conclusion: This curriculum
can promote the attribute of characteristic of SI person and was
highly required to be continued.
Abstract: Simulations of magnetic microstructure in elliptical
Permalloy elements used for controlled motion of magnetic particles
are discussed. The saturating field of the elliptical elements was
studied with respect to lateral dimensions for one-vortex, cross-tie,
diamond and double-diamond states as initial zero-field domain
configurations. With aspect ratio of 1:3 the short axis was varied
from 125 nm to 1000 nm, whereas the thickness was kept constant at
50 nm.
Abstract: In this paper, a novel algorithm based on Ridgelet
Transform and support vector machine is proposed for human action
recognition. The Ridgelet transform is a directional multi-resolution
transform and it is more suitable for describing the human action by
performing its directional information to form spatial features
vectors. The dynamic transition between the spatial features is carried
out using both the Principal Component Analysis and clustering
algorithm K-means. First, the Principal Component Analysis is used
to reduce the dimensionality of the obtained vectors. Then, the kmeans
algorithm is then used to perform the obtained vectors to form
the spatio-temporal pattern, called set-of-labels, according to given
periodicity of human action. Finally, a Support Machine classifier is
used to discriminate between the different human actions. Different
tests are conducted on popular Datasets, such as Weizmann and
KTH. The obtained results show that the proposed method provides
more significant accuracy rate and it drives more robustness in very
challenging situations such as lighting changes, scaling and dynamic
environment