Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: Three batches of yogurts were made with soy protein
isolate (SPI) supplemented with 2% (S2), 4% (S4) or 6% (S6) of
skim milk powder (SMP). The fourth batch (control; S0) was
prepared from SPI without SMP supplementation. Lactobacillus
delbrueckii ssp. bulgaricus ATCC 11842 (Lb 11842) and
Streptococcus thermophilus ST 1342 (ST 1342) were used as the
starter culture. Biotransformation of the inactive forms, isoflavone
glycosides (IG) to biologically active forms, isoflavone aglycones
(IA), was determined during 28 d storage. The viability of both
microorganisms was significantly higher (P < 0.05) in S2, S4, and S6
than that in S0. The ratio of lactic acid/acetic acid in S0 was in the
range of 15.53 – 22.31 compared to 7.24 – 12.81 in S2, S4 and S6.
The biotransformation of IG to IA in S2, S4 and S6 was also
enhanced by 9.9 -13.3% compared to S0.
Abstract: This article provides a comparative analysis of poetries of diverse nations around the world while largely focusing on Kazakh lyric poetry (Kazakh zhyraulyq oneri). Alongside, it sheds the light to the historical development and contemporary progress path of foremost poetry school located along the Syr Darya coast. Hereby, it-s content and central motives are examined.
Abstract: The aim of this study was to investigate ammonium
exchange capacity of natural and activated clinoptilolite from
Kwazulu-Natal Province, South Africa. X – ray fluorescence (XRF)
analysis showed that the clinoptilolite contained exchangeable ions
of sodium, potassium, calcium and magnesium. This analysis also
confirmed that the zeolite sample had a high silicon composition
compared to aluminium. Batch equilibrium studies were performed
in an orbital shaker and the data fitted the Langmuir isotherm very
well. The ammonium exchange capacity was found to increase with
pH and temperature. Clinoptilolite functionalization with
hydrochloric acid increased its ammonia uptake ability.
Abstract: In an electric power system, spinning reserve
requirements can be determined by using deterministic and/or
probabilistic measures. Although deterministic methods are usual in
many systems, application of probabilistic methods becomes
increasingly important in the new environment of the electric power
utility industry. This is because of the increased uncertainty
associated with competition. In this paper 1) a new probabilistic
method is presented which considers the reliability of transmission
system in a simplified manner and 2) deterministic and probabilistic
methods are compared. The studied methods are applied to the Roy
Billinton Test System (RBTS).
Abstract: Larval rearing and seed production of most of tetra fishes (Family: Characidae) is critical due to their small size larvae and limited numbers of spawning attempts. During the present study the effect of different live foods on growth and survival of neon tetra, Paracheirodon innesi larvae (length 3.1 ± 0.012mm, weight 0.048 ± 0.00015mg) and early fry (length = 6.44 ± 0.025mm, weight = 0.64 ± 0.003mg and 13 days old) was determined in two experiments. Experiment I was conducted for rearing the larvae by using mixed green water and Infusoria whereas, in Experiment II, early fry were fed with mixed zooplankton, decapsulated Artemia cyst and Artemia nauplii. The larvae fed on mixed green water showed significant (p
Abstract: Thailand is one of the world-s leaders of rice
producers and exporters. Farmers have to increase the rice cultivation
frequency for serving the national increasing of export-s demand. It
leads to an elimination of rice residues by open burning which is the
quickest and costless management method. The open burning of rice
residue is one of the major causes of air pollutants and greenhouse
gas (GHG) emission. Under ASEAN agreement on trans-boundary
haze, Thailand set the master plan to mitigate air pollutant emission
from open burning of agricultural residues. In this master plan,
residues incorporation is promoted as alternative management
method to open burning. However, the assessment of both options in
term of GHG emission in order to investigate their contribution to
long-term global warming is still scarce or inexistent. In this study, a
method on rice residues assessment was first developed in order to
estimate and compare GHG emissions from rice cultivation under
rice residues open burning and the case with incorporation of the
same amount of rice residues, using 2006 IPCC guidelines for
emission estimation and Life Cycle Analysis technique. The
emission from rice cultivation in different preparing area practice
was also discussed.
Abstract: In this paper, perceptions of actors on changes in
crop productivity, quantity and quality of water, and determinants of
their perception are analyzed using descriptive statistics and ordered
logit model. Data collected from 297 Ethiopian farmers and 103
agricultural professionals from December 2009 to January 2010 are
employed. Results show that the majority of the farmers and
professionals recognized decline in water resources, reasoning
climate changes and soil erosion as some of the causes. However,
there is a variation in views on changes in productivity. The
household asset, education level, age and geographical positions are
found to affect farmers- perception on changes in crop productivity.
But, the study underlines that there is no evidence that farmers-
economic status, age, or education level affects recognition of
degradation of water resources. Thus, more focus shall be given on
providing them different coping mechanisms and alternative
resource conserving technologies than educating about the
problems.
Abstract: Supply chain consists of all stages involved, directly
or indirectly, includes all functions involved in fulfilling a customer
demand. In two stage transportation supply chain problem,
transportation costs are of a significant proportion of final product
costs. It is often crucial for successful decisions making approaches
in two stage supply chain to explicit account for non-linear
transportation costs. In this paper, deterministic demand and finite
supply of products was considered. The optimized distribution level
and the routing structure from the manufacturing plants to the
distribution centres and to the end customers is determined using
developed mathematical model and solved by proposed particle
swarm optimization based genetic algorithm. Numerical analysis of
the case study is carried out to validate the model.
Abstract: In the modern manufacturing systems, the use of
thermal cutting techniques using oxyfuel, plasma and laser have
become indispensable for the shape forming of high quality complex
components; however, the conventional chip removal production
techniques still have its widespread space in the manufacturing
industry. Both these types of machining operations require the
positioning of end effector tool at the edge where the cutting process
commences. This repositioning of the cutting tool in every machining
operation is repeated several times and is termed as non-productive
time or airtime motion. Minimization of this non-productive
machining time plays an important role in mass production with high
speed machining. As, the tool moves from one region to the other by
rapid movement and visits a meticulous region once in the whole
operation, hence the non-productive time can be minimized by
synchronizing the tool movements. In this work, this problem is
being formulated as a general travelling salesman problem (TSP) and
a genetic algorithm approach has been applied to solve the same. For
improving the efficiency of the algorithm, the GA has been
hybridized with a noble special heuristic and simulating annealing
(SA). In the present work a novel heuristic in the combination of GA
has been developed for synchronization of toolpath movements
during repositioning of the tool. A comparative analysis of new Meta
heuristic techniques with simple genetic algorithm has been
performed. The proposed metaheuristic approach shows better
performance than simple genetic algorithm for minimization of nonproductive
toolpath length. Also, the results obtained with the help of
hybrid simulated annealing genetic algorithm (HSAGA) are also
found better than the results using simple genetic algorithm only.
Abstract: A real time image-guided electroplating system is
proposed in this paper. Unlike previous electroplating systems, instead
of using the intermittent mode to electroplate 500um long copper
specimen, a CCD camera and a motion controller are used to adjust
anode-cathode distance to obtain better results. Since the image of the
gap distance is highly deteriorated due to complex chemical-electrical
operation inside the electrolyte, to determine the gap distance, an
image processing algorithm is developed and mainly based on the
entropy and energy values. In addition, the color and incidence
direction of light source are also discussed to help the image process in
this paper. From the experiment results, the specimens created by the
proposed system show better structure, better uniformity and better
finishing surface compared to those by previous intermittent
electroplating setup.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.
Abstract: This paper addresses the problem of peak-to-average
power ratio (PAPR) in orthogonal frequency division multiplexing
(OFDM) systems. It also introduces a new PAPR reduction technique
based on adaptive square-rooting (SQRT) companding process. The
SQRT process of the proposed technique changes the statistical
characteristics of the OFDM output signals from Rayleigh
distribution to Gaussian-like distribution. This change in statistical
distribution results changes of both the peak and average power
values of OFDM signals, and consequently reduces significantly the
PAPR. For the 64QAM OFDM system using 512 subcarriers, up to 6
dB reduction in PAPR was achieved by square-rooting technique
with fixed degradation in bit error rate (BER) equal to 3 dB.
However, the PAPR is reduced at the expense of only -15 dB out-ofband
spectral shoulder re-growth below the in-band signal level. The
proposed adaptive SQRT technique is superior in terms of BER
performance than the original, non-adaptive, square-rooting
technique when the required reduction in PAPR is no more than 5
dB. Also, it provides fixed amount of PAPR reduction in which it is
not available in the original SQRT technique.
Abstract: The paper presents coupled electromagnetic and
thermal field analysis of busbar system (of rectangular cross-section
geometry) submitted to short circuit conditions. The laboratory model
was validated against both analytical solution and experimental
observations. The considered problem required the computation of
the detailed distribution of the power losses and the heat transfer
modes. In this electromagnetic and thermal analysis, different
definitions of electric busbar heating were considered and compared.
The busbar system is a three phase one and consists of aluminum,
painted aluminum and copper busbar. The solution to the coupled
field problem is obtained using the finite element method and the
QuickField™ program. Experiments have been carried out using two
different approaches and compared with computed results.
Abstract: The role of the pollen grain, with to the reproductive
process of higher plants, is to deliver the spermatic cells to the
embryo sac for egg fertilization. The aim of this project was study
the effect of electromagnetic fields on structure and pollen grains
development in Chenopodium album. Anthers of Chenopodium
album L. were collected at different stages of development from
control (without electromagnetic field) and plants grown at 10m from
the field sources. Structure and development of pollen grains were
studied and compared. The studying pollen structure by Light and
Scanning electron microscopy showed that electromagnetic fields
reduction of pollen grains number and male sterility, thus , in some
anthers, pollen grains were attached together and deformed compared
to control ones. The data presented suggest that prolonged exposures
of plants to magnetic field may cause different biological effects at
the cellular tissue and organ levels.
Abstract: It is shown that the relationship of tick-borne
encephalitis virus with the human body comes in two ways, the
development of acute infection with the outcome in convalescence
and long stay by the virus in the body, its persistence in the nervous
tissue with periodic reactivation and prolonged circulating
immunoglobulin M. In spite of the fact that tick-borne encephalitis
virus has a tropism for nerve tissue, involvement in the process of
blood cells is an integral component of the infection. Comprehensive
study of the relation of factors of innate and adaptive immunity in the
tick-borne encephalitis providing insight into the features of chronic
disease.
Abstract: The effect of varying holding temperature on hatching success, occurrence of deformities and mortality rates were investigated for goldlined seabream eggs. Wild broodstock (600 g) were stocked at a 2:1 male-female ratio in a 2 m3 fiberglass tank supplied with filtered seawater (37 g L-1 salinity, temp. range 24±0.5 oC [day] and 22±1 oC [night], DO2 in excess of 5.0mg L-1). Females were injected with 200 IU kg-1 HCG between 08.00 and 10.00 h and returned to tanks to spawn following which eggs were collected by hand using a 100μm net. Fertilized eggs at the gastrulation stage (120 L-1) were randomly placed into one of 12 experimental 6 L aerated (DO2 5 mg L-1) plastic containers with water temperatures maintained at 24±0.5 oC (ambient), 26±0.5 oC, 28± 0.5 oC and 30±0.5 oC using thermostats. Each treatment was undertaken in triplicate using a 12:12 photophase:scotophase photoperiod. No differences were recorded between eggs reared at 24 and 26 oC with respect to viability, deformity, mortality or unhatched egg rates. Increasing temperature reduced the number of viable eggs with those at 30 oC returning poorest performance (P < 0.05). Mortality levels were lowest for eggs incubated at 24 and 26 oC. The greatest level of deformities recorded was that for eggs reared at 28 oC.
Abstract: This article presents a detailed analysis and comparative
performance evaluation of model reference adaptive control systems.
In contrast to classical control theory, adaptive control methods allow
to deal with time-variant processes. Inspired by the works [1] and
[2], two methods based on the MIT rule and Lyapunov rule are
applied to a linear first order system. The system is simulated and
it is investigated how changes to the adaptation gain affect the
system performance. Furthermore, variations in the reference model
parameters, that is changing the desired closed-loop behaviour are
examinded.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.