Abstract: Evaporator is an important and widely used heat
exchanger in air conditioning and refrigeration industries. Different
methods have been used by investigators to increase the heat transfer
rates in evaporators. One of the passive techniques to enhance heat
transfer coefficient is the application of microfin tubes. The
mechanism of heat transfer augmentation in microfin tubes is
dependent on the flow regime of two-phase flow. Therefore many
investigations of the flow patterns for in-tube evaporation have been
reported in literatures. The gravitational force, surface tension and
the vapor-liquid interfacial shear stress are known as three dominant
factors controlling the vapor and liquid distribution inside the tube. A
review of the existing literature reveals that the previous
investigations were concerned with the two-phase flow pattern for
flow boiling in horizontal tubes [12], [9]. Therefore, the objective of
the present investigation is to obtain information about the two-phase
flow patterns for evaporation of R-134a inside horizontal smooth and
microfin tubes. Also Investigation of heat transfer during flow
boiling of R-134a inside horizontal microfin and smooth tube have
been carried out experimentally The heat transfer coefficients for
annular flow in the smooth tube is shown to agree well with Gungor
and Winterton-s correlation [4]. All the flow patterns occurred in the
test can be divided into three dominant regimes, i.e., stratified-wavy
flow, wavy-annular flow and annular flow. Experimental data are
plotted in two kinds of flow maps, i.e., Weber number for the vapor
versus weber number for the liquid flow map and mass flux versus
vapor quality flow map. The transition from wavy-annular flow to
annular or stratified-wavy flow is identified in the flow maps.
Abstract: Preliminary results for a new flat plate test
facility are presented here in the form of Computational Fluid Dynamics (CFD), flow visualisation, pressure measurements and thermal anemometry. The results from the CFD and flow
visualisation show the effectiveness of the plate design, with the trailing edge flap anchoring the stagnation point on the working surface and reducing the extent of the leading edge separation. The flow visualization technique demonstrates the
two-dimensionality of the flow in the location where the
thermal anemometry measurements are obtained.
Measurements of the boundary layer mean velocity profiles compare favourably with the Blasius solution, thereby allowing for comparison of future measurements with the
wealth of data available on zero pressure gradient Blasius
flows. Results for the skin friction, boundary layer thickness,
frictional velocity and wall shear stress are shown to agree well with the Blasius theory, with a maximum experimental deviation from theory of 5%. Two turbulence generating grids
have been designed and characterized and it is shown that the turbulence decay downstream of both grids agrees with established correlations. It is also demonstrated that there is
little dependence of turbulence on the freestream velocity.
Abstract: The study of the stress distribution on a hollow
cylindrical fiber placed in a composite material is considered in this
work and an analytical solution for this stress distribution has been
constructed. Finally some parameters such as fiber-s thickness and
fiber-s length are considered and their effects on the distribution of
stress have been investigated. For finding the governing relations,
continuity equations for the axisymmetric problem in cylindrical
coordinate (r,o,z) are considered. Then by assuming some conditions
and solving the governing equations and applying the boundary
conditions, an equation relates the stress applied to the representative
volume element with the stress distribution on the fiber has been
found.
Abstract: At the previous study of new metal gasket, contact
width and contact stress were important design parameter for
optimizing metal gasket performance. However, the range of contact
stress had not been investigated thoroughly. In this study, we
conducted a gasket design optimization based on an elastic and plastic
contact stress analysis considering forming effect using FEM. The
gasket model was simulated by using two simulation stages which is
forming and tightening simulation. The optimum design based on an
elastic and plastic contact stress was founded. Final evaluation was
determined by helium leak quantity to check leakage performance of
both type of gaskets. The helium leak test shows that a gasket based
on the plastic contact stress design better than based on elastic stress
design.
Abstract: The Euler-s equation of motion is extended to include
the viscosity stress tensor leading to the formulation of Navier–
Stokes type equation. The latter is linearized and applied to
investigate the rotational motion or vorticity in a viscous fluid.
Relations for the velocity of viscous waves and attenuation parameter
are obtained in terms of viscosity (μ) and the density (¤ü) of the fluid.
μ and ¤ü are measured experimentally as a function of temperature for
two different samples of light and heavy crude oil. These data
facilitated to determine the activation energy, velocity of viscous
wave and the attenuation parameter. Shear wave velocity in heavy oil
is found to be much larger than the light oil, whereas the attenuation
parameter in heavy oil is quite low in comparison to light one. The
activation energy of heavy oil is three times larger than light oil.
Abstract: Using the finite element analyses, this paper discusses the effects of temperature-dependent material properties on the stress and temperature fields in a cracked metal plate under the electric current load. The practical and complicated results are obtained when the temperature-dependent material properties are adopted in the analysis. If the simplified (temperature-independent) material properties are used, incorrect results will be obtained.
Abstract: Simulation of occlusal function during laboratory
material-s testing becomes essential in predicting long-term
performance before clinical usage. The aim of the study was to assess
the influence of chamfer preparation depth on failure risk of heat
pressed ceramic crowns with and without zirconia framework by
means of finite element analysis. 3D models of maxillary central
incisor, prepared for full ceramic crowns with different depths of the
chamfer margin (between 0.8 and 1.2 mm) and 6-degree tapered
walls together with the overlying crowns were generated using
literature data (Fig. 1, 2). The crowns were designed with and
without a zirconia framework with a thickness of 0.4 mm. For all
preparations and crowns, stresses in the pressed ceramic crown,
zirconia framework, pressed ceramic veneer, and dentin were
evaluated separately. The highest stresses were registered in the
dentin. The depth of the preparations had no significant influence on
the stress values of the teeth and pressed ceramics for the studied
cases, only for the zirconia framework. The zirconia framework
decreases the stress values in the veneer.
Abstract: This paper presents anapproach of hybridizing two or more artificial intelligence (AI) techniques which arebeing used to
fuzzify the workstress level ranking and categorize the rating accordingly. The use of two or more techniques (hybrid approach)
has been considered in this case, as combining different techniques may lead to neutralizing each other-s weaknesses generating a
superior hybrid solution. Recent researches have shown that there is a
need for a more valid and reliable tools, for assessing work stress. Thus artificial intelligence techniques have been applied in this
instance to provide a solution to a psychological application. An overview about the novel and autonomous interactive model for analysing work-stress that has been developedusing multi-agent
systems is also presented in this paper. The establishment of the intelligent multi-agent decision analyser (IMADA) using hybridized technique of neural networks and fuzzy logic within the multi-agent based framework is also described.
Abstract: In built-up structures, one of the effective ways of
dissipating unwanted vibration is to exploit the occurrence of slip at
the interfaces of structural laminates. The present work focuses on
the dynamic analysis of welded structures. A mathematical
formulation has been developed for the mechanism of slip damping
in layered and welded mild steel beams with unequal thickness
subjected to both periodic and non-periodic forces. It is observed that
a number of vital parameters such as; thickness ratio, pressure
distribution characteristics, relative slip and kinematic co-efficient of
friction at the interfaces, nature of exciting forces, length and
thickness of the beam specimen govern the damping characteristics of
these structures. Experimental verification has been carried out to
validate the analysis and study the effect of these parameters. The
developed damping model for the structure is found to be in fairly
good agreement with the measured data. Finally, the results of the
analysis are discussed and rationalized.
Abstract: The purpose of this work was to study the effect of the
irrigation using waste water with various electric conductivities (T(0,92ds/m), EC3 (3ds/m) and EC6 (6ds/m) on three varieties of
quinoa cultivated in a field south of Morocco. The follow up of the evolution of the chemical and agronomic parameters throughout the
culture made it possible to determine the responses to the saline stress in arid conditions. Results showed that the salinity caused the
depression of plant-s height, and reduced the fresh and dry weight in
the different parts of the three varieties plants. The increase of the irrigation water EC didn-t affect the yield for the varieties. Thus,
quinoa resisted to salinity and proved a behavior of a facultative halophyte crop. In fact, the cultivation of this using treated wastewater is feasible especially in arid areas for a sustainable use of
water resources.
Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: This paper presents a numerical approach for the static
and dynamic analysis of hydrodynamic radial journal bearings. In the
first part, the effect of shaft and housing deformability on pressure
distribution within oil film is investigated. An iterative algorithm that
couples Reynolds equation with a plane finite elements (FE)
structural model is solved. Viscosity-to-pressure dependency (Vogel-
Barus equation) is also included. The deformed lubrication gap and
the overall stress state are obtained. Numerical results are presented
with reference to a typical journal bearing configuration at two
different inlet oil temperatures. Obtained results show the great
influence of bearing components structural deformation on oil
pressure distribution, compared with results for ideally rigid
components. In the second part, a numerical approach based on
perturbation method is used to compute stiffness and damping
matrices, which characterize the journal bearing dynamic behavior.
Abstract: The effect of the discontinuity of the rail ends and the
presence of lower modulus insulation material at the gap to the
variations of stresses in the insulated rail joint (IRJ) is presented. A
three-dimensional wheel – rail contact model in the finite element
framework is used for the analysis. It is shown that the maximum stress
occurs in the subsurface of the railhead when the wheel contact occurs
far away from the rail end and migrates to the railhead surface as the
wheel approaches the rail end; under this condition, the interface
between the rail ends and the insulation material has suffered
significantly increased levels of stress concentration. The ratio of the
elastic modulus of the railhead and insulation material is found to alter
the levels of stress concentration. Numerical result indicates that a
higher elastic modulus insulating material can reduce the stress
concentration in the railhead but will generate higher stresses in the
insulation material, leading to earlier failure of the insulation material
Abstract: This paper study the behavior of the solution at the crack edges for an elliptical crack with developing cusps, Ω in the plane elasticity subjected to shear loading. The problem of finding the resulting shear stress can be formulated as a hypersingular integral equation over Ω and it is then transformed into a similar equation over a circular region, D, using conformal mapping. An appropriate collocation points are chosen on the region D to reduce the hypersingular integral equation into a system of linear equations with (2N+1)(N+1) unknown coefficients, which will later be used in the determination of shear stress intensity factors and maximum shear stress intensity. Numerical solution for the considered problem are compared with the existing asymptotic solution, and displayed graphically. Our results give a very good agreement to the existing asymptotic solutions.
Abstract: The application of agro-industrial waste in Aluminum
Metal Matrix Composites has been getting more attention as they
can reinforce particles in metal matrix which enhance the strength
properties of the composites. In addition, by applying these agroindustrial
wastes in useful way not only save the manufacturing cost
of products but also reduce the pollutions on environment. This
paper represents a literature review on a range of industrial wastes
and their utilization in metal matrix composites. The paper describes
the synthesis methods of agro-industrial waste filled metal matrix
composite materials and their mechanical, wear, corrosion, and
physical properties. It also highlights the current application and
future potential of agro-industrial waste reinforced composites in
aerospace, automotive and other construction industries.
Abstract: This paper presents the effect of driving a motor
vehicle on the stress levels of older drivers, indicated by monitoring
their hear rate increase whilst completing various everyday driving
tasks. Results suggest that whilst older female drivers heart rate varied
more significantly than males, the actual age of a participant did not
result in a significant change in heart rate due to stress, within the age
group tested. The analysis of the results indicates the most stressful
manoeuvres undertaken by the older drivers and highlights the tasks
which were found difficult with a view to implementing technologies
to aid the more senior driver in automotive travel.
Abstract: The aim of this study is to investigate the effect of
perceived social support and stress on the coping capability and level
of depression of foreign and local students in Malaysia. Using
convenience sampling, 200 students from three universities in
Selangor, Malaysia participated in the study. The results of this study
revealed that there was a significant relationship between perceived
social support and coping capability. It is also found that there is a
negative relationship between coping capability and depression.
Further, stress and depression are positively related whereas stress
and coping capability are negatively related. Lastly, there is no
significant difference for the stress level and coping capability
amongst local and foreign students.
Abstract: Photoselective plastic films with thermic properties
are now available so that greenhouses clad with such plastics exhibit
a higher degree of “Greenhouse Effect” with a consequent increase in
night time temperature. In this study, we investigate the potential
benefits of a range of thermic plastic films used as greenhouse cover
materials on the vegetative and reproductive growth and development
of Iceberg lettuce (Lactuca sativa L). Transplants were grown under
thermic films and destructively harvested 4, 5, and 6 weeks after
transplanting. Thermic films can increase night temperatures up to 2
⁰C reducing the wide fluctuation in greenhouse temperature during
winter compared to the standard commercial film and consequently
increased the yield (leaf number, fresh weight, and dry weight) of
lettuce plants. Lettuce plants grown under Clear film respond to cold
stress by the accumulation of secondary products (phenolics, and
flavonoids).
Abstract: The objective of this research was to find the diffusion properties of vehicles on the road by using the V-Sphere Code. The diffusion coefficient and the size of the height of the wake were estimated with the LES option and the third order MUSCL scheme. We evaluated the code with the changes in the moments of Reynolds Stress along the mean streamline. The results show that at the leading part of a bluff body the LES has some advantages over the RNS since the changes in the strain rates are larger for the leading part. We estimated that the diffusion coefficient with the computed Reynolds stress (non-dimensional) was about 0.96 times the mean velocity.
Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.