Abstract: The 5th generation of mobile networks is term used in
various research papers and projects to identify the next major phase
of mobile telecommunications standards. 5G wireless networks will
support higher peak data rate, lower latency and provide best
connections with QoS guarantees.
In this article, we discuss various promising technologies for 5G
wireless communication systems, such as IPv6 support, World Wide
Wireless Web (WWWW), Dynamic Adhoc Wireless Networks
(DAWN), BEAM DIVISION MULTIPLE ACCESS (BDMA), Cloud
Computing, cognitive radio technology and FBMC/OQAM.
This paper is organized as follows: First, we will give introduction
to 5G systems, present some goals and requirements of 5G. In the
next, basic differences between 4G and 5G are given, after we talk
about key technology innovations of 5G systems and finally we will
conclude in last Section.
Abstract: The paper presents a novel screening method to
indicate congenital heart diseases (CHD), which otherwise could
remain undetected because of their low level. Therefore, not
belonging to the high-risk population, the pregnancies are not subject
to the regular fetal monitoring with ultrasound echocardiography.
Based on the fact that CHD is a morphological defect of the heart
causing turbulent blood flow, the turbulence appears as a murmur,
which can be detected by fetal phonocardiography (fPCG). The
proposed method applies measurements on the maternal abdomen
and from the recorded sound signal a sophisticated processing
determines the fetal heart murmur. The paper describes the problems
and the additional advantages of the fPCG method including the
possibility of measurements at home and its combination with the
prescribed regular cardiotocographic (CTG) monitoring. The
proposed screening process implemented on a telemedicine system
provides an enhanced safety against hidden cardiac diseases.
Abstract: The substantial development of the construction
industry has forced the cement industry, its major support, to focus
on achieving maximum productivity to meet the growing demand for
this material. This means that the reliability of a cement production
system needs to be at the highest level that can be achieved by good
maintenance. This paper studies the extent to which the
implementation of RCM is needed as a strategy for increasing the
reliability of the production systems component can be increased,
thus ensuring continuous productivity. In a case study of four Libyan
cement factories, 80 employees were surveyed and 12 top and middle
managers interviewed. It is evident that these factories usually
breakdown more often than once per month which has led to a
decline in productivity. In many times they cannot achieve the
minimum level of production amount. This has resulted from the
poor reliability of their production systems as a result of poor or
insufficient maintenance. It has been found that most of the factories’
employees misunderstand maintenance and its importance. The main
cause of this problem is the lack of qualified and trained staff, but in
addition it has been found that most employees are not found to be
motivated as a result of a lack of management support and interest. In
response to these findings, it has been suggested that the RCM
strategy should be implemented in the four factories. The results
show the importance of the development of maintenance strategies
through the implementation of RCM in these factories. The purpose
of it would be to overcome the problems that could secure the
reliability of the production systems. This study could be a useful
source of information for academic researchers and the industrial
organizations which are still experiencing problems in maintenance
practices.
Abstract: Masonry infill walls are inevitable in the selfsupporting
structures, but their contribution in the resistance to
earthquake loads is generally neglected in the structural analyses. The
principal aim of this work through a numerical study of masonry
infill walls behavior in structures subjected to horizontal load is to
propose by finite elements numerical modeling, a more reliable
approach, faster and close to reality. In this study, 3D Finite Element
Analysis was developed to study the behavior of masonry infill walls
in structures subjected to horizontal load; the finite element software
being used was ABAQUS, it is observed that more rigidity of the
masonry filling is significant, more the structure is rigid, we can so
conclude that the filling brings an additional rigidity to the structure
not to be neglected; it is also observed that when the framework is
subjected to horizontal loads, the framework separates from the
filling on the level of the tended diagonal.
Abstract: Computational fluid dynamics analysis of the burning
of syngas fuels derived from biomass and plastic solid waste mixture
through gasification process is presented in this paper. The syngas
fuel is burned in gas turbine can combustor. Gas turbine can
combustor with swirl is designed to burn the fuel efficiently and
reduce the emissions. The main objective is to test the impact of the
alternative syngas fuel compositions and lower heating value on the
combustion performance and emissions. The syngas fuel is produced
by blending palm kernel shell (PKS) with polyethylene (PE) waste
via catalytic steam gasification (fluidized bed reactor). High
hydrogen content syngas fuel was obtained by mixing 30% PE waste
with PKS. The syngas composition obtained through the gasification
process is 76.2% H2, 8.53% CO, 4.39% CO2 and 10.90% CH4. The
lower heating value of the syngas fuel is LHV = 15.98 MJ/m3. Three
fuels were tested in this study natural gas (100%CH4), syngas fuel
and pure hydrogen (100% H2). The power from the combustor was
kept constant for all the fuels tested in this study. The effect of syngas
fuel composition and lower heating value on the flame shape, gas
temperature, mass of carbon dioxide (CO2) and nitrogen oxides
(NOX) per unit of energy generation is presented in this paper. The
results show an increase of the peak flame temperature and NO mass
fractions for the syngas and hydrogen fuels compared to natural gas
fuel combustion. Lower average CO2 emissions at the exit of the
combustor are obtained for the syngas compared to the natural gas
fuel.
Abstract: This study focuses on a novel method for dispersion
and distribution of reinforcement under high intensive shear stress to
produce metal composites. The polyacrylonitrile (PAN)-based short
carbon fiber (Csf) and Nextel 610 alumina fiber were dispersed under
high intensive shearing at mushy zone in semi-solid of A356 by a
novel method. The bundles and clusters were embedded by
infiltration of slurry into the clusters, thus leading to a uniform
microstructure. The fibers were embedded homogenously into the
aluminum around 576-580°C with around 46% of solid fraction.
Other experiments at 615°C and 568°C which are contained 0% and
90% solid respectively were not successful for dispersion and
infiltration of aluminum into bundles of Csf. The alumina fiber has
been cracked by high shearing load. The morphologies and
crystalline phase were evaluated by SEM and XRD. The adopted
thixo-process effectively improved the adherence and distribution of
Csf into Al that can be developed to produce various composites by
thixomixing.
Abstract: The concept of economic policy and the practical
economic policy diverge from each other at a certain stage of
development. This is related to the concept of realization of the
underlying problems. It comes with all the problems emerged in the
market oriented economic order due to the political processes based
on social welfare policy. The realization of the concept of economic
policy is impeded by economic and political obstacles. If you want to
fill the appeared between the concept and reality, it is necessary to
identify and avoid these obstacles. It requires the following: increase
of the level of the knowledge of prevention technology in
understanding of economic relations, as well as political aspects of
the formation of ideas; perfection of economic policy toolkit, and
political methods.
It is necessary to realize what is the main precondition of
implementation and further development of the concept of economic
policy, as well as the formation of opinions about economic and
public safety. This is a broad consensus on the basic values of the
content and the scale of action, which the general public wants to be
realized.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: In contrast with literal meaning of nano, researchers
have been achieved mega adventures in this area and every day more
nanomaterials are being introduced to the market. After long time
application of fossil-based plastics, nowadays accumulation of their
waste seems to be a big problem to the environment. On the other
hand, mankind has more attention to safety and living environment.
Replacing common plastic packaging materials with degradable ones
that degrade faster and convert to non-dangerous components like
water and carbon dioxide have more attractions; these new materials
are based on renewable and inexpensive sources of starch and
cellulose. However, the functional properties of them do not suitable
for packaging. At this point, nanotechnology has an important role.
Utilizing of nanomaterials in polymer structure will improve
mechanical and physical properties of them; nanocrystalline cellulose
(NCC) has this ability. This work has employed a chemical method to
produce NCC and starch bio nanocomposite containing NCC. X-Ray
Diffraction technique has characterized the obtained materials.
Results showed that applied method is a suitable one as well as
applicable one to NCC production.
Abstract: This paper deals with the study of reflection and
transmission characteristics of acoustic waves at the interface of a
semiconductor half-space and elastic solid. The amplitude ratios
(reflection and transmission coefficients) of reflected and transmitted
waves to that of incident wave varying with the incident angles have
been examined for the case of quasi-longitudinal wave. The special
cases of normal and grazing incidence have also been derived with
the help of Gauss elimination method. The mathematical model
consisting of governing partial differential equations of motion and
charge carriers’ diffusion of n-type semiconductors and elastic solid
has been solved both analytically and numerically in the study. The
numerical computations of reflection and transmission coefficients
has been carried out by using MATLAB programming software for
silicon (Si) semiconductor and copper elastic solid. The computer
simulated results have been plotted graphically for Si
semiconductors. The study may be useful in semiconductors,
geology, and seismology in addition to surface acoustic wave (SAW)
devices.
Abstract: This paper presents an optimization method for
reducing the number of input channels and the complexity of the
feed-forward NARX neural network (NN) without compromising the
accuracy of the NN model. By utilizing the correlation analysis
method, the most significant regressors are selected to form the input
layer of the NN structure. An application of vehicle dynamic model
identification is also presented in this paper to demonstrate the
optimization technique and the optimal input layer structure and the
optimal number of neurons for the neural network is investigated.
Abstract: Toddy sediment (TS) was cultured in a PDA medium
to determine initial yeast load, and also it was undergone sun, shade,
solar, dehumidified cold air (DCA) and hot air oven (at 400, 500 and
60oC) drying with a view to preserve viability of yeast. Thereafter,
this study was conducted according to two factor factorial design in
order to determine best preservation method. Therein the dried TS
from the best drying method was taken and divided into two portions.
One portion was mixed with 3: 7 ratio of TS: rice flour and the
mixture was divided in to two again. While one portion was kept
under in house condition the other was in a refrigerator. Same
procedure was followed to the rest portion of TS too but it was at the
same ratio of corn flour. All treatments were vacuum packed in triple
laminate pouches and the best preservation method was determined
in terms of leavening index (LI). The TS obtained from the best
preservation method was used to make foods (bread and hopper) and
organoleptic properties of it were evaluated against same of ordinary
foods using sensory panel with a five point hedonic scale.
Results revealed that yeast load or fresh TS was 58×106 CFU/g.
The best drying method in preserving viability of yeast was DCA
because LI of this treatment (96%) is higher than that of other three
treatments. Organoleptic properties of foods prepared from best
preservation method are as same as ordinary foods according to Duo
trio test.
Abstract: Pneumatic reactors have been widely employed in various sectors of the chemical industry, especially where are required high heat and mass transfer rates. This study aimed to obtain correlations that allow the prediction of gas hold-up (Ԑ) and volumetric oxygen transfer coefficient (kLa), and compare these values, for three models of pneumatic reactors on two scales utilizing Newtonian fluids. Values of kLa were obtained using the dynamic pressure-step method, while e was used for a new proposed measure. Comparing the three models of reactors studied, it was observed that the mass transfer was superior to draft-tube airlift, reaching e of 0.173 and kLa of 0.00904s-1. All correlations showed good fit to the experimental data (R2≥94%), and comparisons with correlations from the literature demonstrate the need for further similar studies due to shortage of data available, mainly for airlift reactors and high viscosity fluids.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: This paper examines the system protection for cyber-physical
systems (CPS). CPS are particularly characterized by their
networking system components. This means they are able to adapt to
the needs of their users and its environment. With this ability, CPS
have new, specific requirements on the protection against anti-counterfeiting,
know-how loss and manipulation. They increase the
requirements on system protection because piracy attacks can be
more diverse, for example because of an increasing number of
interfaces or through the networking abilities. The new requirements
were identified and in a next step matched with existing protective
measures. Due to the found gap the development of new protection
measures has to be forced to close this gap. Moreover a comparison
of the effectiveness between selected measures was realized and the
first results are presented in this paper.
Abstract: This paper presents the results of an experimental
study undertaken to evaluate the local bond stress-slip response of
short embedment of reinforcing bars in normal concrete (NC) and
high performance fiber reinforced cement composites (HPFRCC)
blocks. Long embedment was investigated as well to gain insights on
the distribution of strain, slip, bar stress and bond stress along the bar
especially in post-yield range. A total of 12 specimens were tested,
by means of pull-out of the reinforcing bars from concrete blocks. It
was found that the enhancement of local bond strength can be
reached up to 50% and ductility of the bond behavior was improved
significantly if HPFRCC is used. Also, under a constant strain at
loaded end, HPFRCC has delayed yielding of bars at other location
from the loaded end. Hence, the reduction of bond stress was slower
for HPFRCC in comparison with NC. Due to the same reason, the
total slips at loaded end for HPFRCC was smaller than NC as
expected. Test results indicated that HPFRCC has better bond slip
behavior which makes it a suitable material to be employed in
anchorage zone such as beam-column joints.
Abstract: In this paper, a new concept of closed-loop design for a
product is presented. The closed-loop design model is developed by
integrating forward design and reverse design. Based on this new
concept, a closed-loop design model for sustainable manufacturing by
integrated evaluation of forward design, reverse design, and green
manufacturing using a fuzzy analytic network process is developed. In
the design stage of a product, with a given product requirement and
objective, there can be different ways to design the detailed
components and specifications. Therefore, there can be different
design cases to achieve the same product requirement and objective.
Subsequently, in the design evaluation stage, it is required to analyze
and evaluate the different design cases. The purpose of this research is
to develop a model for evaluating the design cases by integrated
evaluating the criteria in forward design, reverse design, and green
manufacturing. A fuzzy analytic network process method is presented
for integrated evaluation of the criteria in the three models. The
comparison matrices for evaluating the criteria in the three groups are
established. The total relational values among the three groups
represent the total relational effects. In applications, a super matrix
model is created and the total relational values can be used to evaluate
the design cases for decision-making to select the final design case. An
example product is demonstrated in this presentation. It shows that the
model is useful for integrated evaluation of forward design, reverse
design, and green manufacturing to achieve a closed-loop design for
sustainable manufacturing objective.
Abstract: This paper presents a method of evaluating the effect
of aggregate angularity on hot mix asphalt (HMA) properties and its
relationship to the Permanent Deformation resistance. The research
concluded that aggregate particle angularity had a significant effect
on the Permanent Deformation performance, and also that with an
increase in coarse aggregate angularity there was an increase in the
resistance of mixes to Permanent Deformation. A comparison
between the measured data and predictive data of permanent
deformation predictive models showed the limits of existing
prediction models. The numerical analysis described the permanent
deformation zones and concluded that angularity has an effect of the
onset of these zones. Prediction of permanent deformation help road
agencies and by extension economists and engineers determine the
best approach for maintenance, rehabilitation, and new construction
works of the road infrastructure.
Abstract: Some plants of genus Schinus have been used in the
folk medicine as topical antiseptic, digestive, purgative, diuretic,
analgesic or antidepressant, and also for respiratory and urinary
infections. Chemical composition of essential oils of S. molle and S.
terebinthifolius had been evaluated and presented high variability
according with the part of the plant studied and with the geographic
and climatic regions. The pharmacological properties, namely
antimicrobial, anti-tumoural and anti-inflammatory activities are
conditioned by chemical composition of essential oils. Taking into
account the difficulty to infer the pharmacological properties of
Schinus essential oils without hard experimental approach, this work
will focus on the development of a decision support system, in terms
of its knowledge representation and reasoning procedures, under a
formal framework based on Logic Programming, complemented with
an approach to computing centered on Artificial Neural Networks
and the respective Degree-of-Confidence that one has on such an
occurrence.
Abstract: Optical biosensors have become a powerful detection
and analysis tool for wide-ranging applications in biomedical research,
pharmaceuticals and environmental monitoring. This study carried out
the computational fluid dynamics (CFD)-based simulations to explore
the dispersion phenomenon in the micro channel of an optical
biosensor. The predicted time sequences of concentration contours
were utilized to better understand the dispersion development occurred
in different geometric shapes of micro channels. The simulation results
showed the surface concentrations at the sensing probe (with the best
performance of a grating coupler) in respect of time to appraise the
dispersion effect and therefore identify the design configurations
resulting in minimum dispersion.