Abstract: In the past decade, the use of digital image correlation
(DIC) techniques has increased significantly in the area of
experimental mechanics, especially for materials behavior
characterization. This non-contact tool enables full field displacement
and strain measurements over a complete region of interest. The DIC
algorithm requires a random contrast pattern on the surface of the
specimen in order to perform properly. To create this pattern, the
specimen is usually first coated using a white matt paint. Next, a
black random speckle pattern is applied using any suitable method. If
the applied paint coating is too thick, its top surface may not be able
to exactly follow the deformation of the specimen, and consequently,
the strain measurement might be underestimated. In the present
article, a study of the influence of the paint thickness on the strain
underestimation is performed for different strain levels. The results
are then compared to typical paint coating thicknesses applied by
experienced DIC users. A slight strain underestimation was observed
for paint coatings thicker than about 30μm. On the other hand, this
value was found to be uncommonly high compared to coating
thicknesses applied by DIC users.
Abstract: To mitigate the urban heat island effect has become a
global issue when we are faced with the challenge of climate change.
Through literature review, plant photosynthesis can reduce the carbon
dioxide and mitigate the urban heat island effect to a degree. Because
there are not enough open space and parks, green roof has become an
important policy in Taiwan.
We selected elementary school buildings in northern New Taipei
City as research subjects since elementary schools are asked with
priority to build green roof and important educational place to promote
green roof concept. Testo175-H1 recording device was used to record
the temperature and humidity differences between roof surface and
interior space below roof with and without green roof in the long-term.
We also use questionnaires to investigate the awareness of comfort
level of green roof and sensation of teachers and students of the
elementary schools.
The results indicated that the temperature of roof without greening
was higher than that with greening by about 2°C. But sometimes
during noontime, the temperature of green roof was higher than that of
non-green roof probably because of the character of the accumulation
and dissipation of heat of greening. The temperature of the interior
space below green roof was normally lower than that without green
roof by about 1°C, showing that green roof could lower the
temperature. The humidity of the green roof was higher than the one
without greening also indicated that green roof retained water better.
Teachers liked to combine green roof concept in the curriculum,
and students wished all classes can take turns to maintain the green
roof. Teachers and students whose school had integrated green roof
concept in the curriculum were more willing to participate in the
maintenance work of green roof. Teachers and students who may have
access to and touch the green roof can be more aware of the green roof
benefit. We suggest architects to increase the accessibility and
visibility of green roof, such as use it as a part of the activity space.
This idea can be a reference to the green roof curriculum design.
Abstract: The popularity of quality management system models
continues to grow despite the transitional crisis in 2008. Their
development is associated with demands of the new requirements for
entrepreneurs, such as risk analysis projects and more emphasis on
supervision of outsourced processes. In parallel, it is appropriate to
focus attention on the selection of companies aspiring to a quality
management system. This is particularly important in the automotive
supplier industry, where requirements transferred to the levels in the
supply chain should be clear, transparent and fairly satisfied. The
author has carried out a series of researches aimed at finding the
factors that allow for the effective implementation of the quality
management system in automotive companies. The research was
focused on four groups of companies: 1) manufacturing (parts and
assemblies for the purpose of sale or for vehicle manufacturers), 2)
service (repair and maintenance of the car) 3) services for the
transport of goods or people, 4) commercial (auto parts and vehicles).
The identified determinants were divided into two types of criteria:
internal and external, as well as hard and soft. The article presents the
hard – technical factors that an automotive company must meet in
order to achieve the goal of the quality management system
implementation.
Abstract: Students' academic achievement, along with the
effects of different variables, has been a serious concern of educators
since long ago. This study was an attempt to investigate the interplay
of Locus of Control (LOC), academic achievement and biological
variables among Iranian online EFL Learners. The participants of the
study included 100 students of different age groups and genders
studying English online at Iran Language Institute (ILI), Isfahan,
Iran. The instrument used was Trice Academic LOC questionnaire
which identifies orientations of internality or externality. The
participants' Grade Point Averages (GPAs) were used as the measure
of their academic achievement. A series of independent samples ttests
were performed on the data. The results of the study showed that
(a) there were no significant differences between male and female
participants in LOC orientation, (b) there was no relationship
between LOC and academic achievement among internal males and
females, (c) external females were better achievers than external
males, (d) and the age had no significant relationship with LOC and
academic achievement. It can be concluded that the social, cultural
patterns of genders have changed. This study might help sociologists
and psychologists as well as applied linguists in that they reflect the
recent social changes and their effects on the LOC and their
consequent implications in teaching languages.
Abstract: This article proposes a new method for application in
communication circuit systems that increase efficiency, PAE, output
power and gain in the circuit. The proposed method is based on a
combination of switching class-E and class-J and has been termed
class-EJ. This method was investigated using both theory and
simulation to confirm ∼72% PAE and output power of >39dBm. The
combination and design of the proposed power amplifier accrues gain
of over 15dB in the 2.9 to 3.5GHz frequency bandwidth. This circuit
was designed using MOSFET and high power transistors. The loadand
source-pull method achieved the best input and output networks
using lumped elements. The proposed technique was investigated for
fundamental and second harmonics having desirable amplitudes for
the output signal.
Abstract: The objective of this paper is to present the process of
change in management accounting in Romania, a former communist
country from Eastern Europe. In order to explain this process, we used
the contingency and institutional theories. We focused on the
following directions: the presentation of the scientific context and
motivation of this research and the case study. We presented the state
of the art in the process of change in the management accounting from
the international and national perspective. We also described the
evolution of management accounting in Romania in the context of
economic and political changes. An important moment was the fall of
communism in 1989. This represents a starting point for a new
economic environment and for new management accounting.
Accordingly, we developed a case study which presented this
evolution. The conclusion of our research was that the changes in the
management accounting system of the company analysed occurred in
the same time with the institutionalisation of some elements (e.g.
degree of competition, training and competencies in management
accounting). The management accounting system was modelled by the
contingencies specific to this company (e.g. environment, industry,
strategy).
Abstract: Image segmentation and edge detection is a fundamental section in image processing. In case of noisy images Edge Detection is very less effective if we use conventional Spatial Filters like Sobel, Prewitt, LOG, Laplacian etc. To overcome this problem we have proposed the use of Stochastic Gradient Mask instead of Spatial Filters for generating gradient images. The present study has shown that the resultant images obtained by applying Stochastic Gradient Masks appear to be much clearer and sharper as per Edge detection is considered.
Abstract: Optimal feeding, including optimal micronutrient
intake, becomes one of the ways to overcome the long-term
consequences of undernutrition. Macronutrient and micronutrient
intake were important to a rapid growth and development of young
children. The study objective was to assess macro and micronutrient
intake and its adequacy in children aged 12-23 months. This survey
was a cross-sectional study, involving 83 caregivers with children
aged 12-23 months old in Senen Sub-district, Central Jakarta selected
through simple random sampling. Data on nutrient intake was
obtained through interview using single 24-hour recall. Repeated 24-
hour recall to sub-sample was done to estimate the proportion of
nutrient inadequacy. The highest prevalence of nutrient inadequacy
was iron (52.4%), followed by vitamin C (30.9%) and zinc (28.8%).
Almost 12% children had inadequate energy intake. More than half
of children (62.6%) were anemic (25.3% were severely anemic).
Micronutrient inadequacy, especially iron, was more problematic
than macronutrient inadequacy in the study area.
Abstract: A novel design technique employing CMOS Current
Feedback Operational Amplifier (CFOA) is presented. The feature of
consumption very low power in designing pseudo-OTA is used to
decreasing the total power consumption of the proposed CFOA. This
design approach applies pseudo-OTA as input stage cascaded with
buffer stage. Moreover, the DC input offset voltage and harmonic
distortion (HD) of the proposed CFOA are very low values compared
with the conventional CMOS CFOA due to the symmetrical input
stage. P-Spice simulation results are obtained using 0.18μm MIETEC
CMOS process parameters and supply voltage of ±1.2V, 50μA
biasing current. The p-spice simulation shows excellent improvement
of the proposed CFOA over existing CMOS CFOA. Some of these
performance parameters, for example, are DC gain of 62. dB, openloop
gain bandwidth product of 108 MHz, slew rate (SR+) of
+71.2V/μS, THD of -63dB and DC consumption power (PC) of
2mW.
Abstract: The Trustworthy link failure recovery algorithm is
introduced in this paper, to provide the forwarding continuity even
with compound link failures. The ephemeral failures are common in
IP networks and it also has some proposals based on local rerouting.
To ensure forwarding continuity, we are introducing the compound
link failure recovery algorithm, even with compound link failures.
For forwarding the information, each packet carries a blacklist, which
is a min set of failed links encountered along its path, and the next
hop is chosen by excluding the blacklisted links. Our proposed
method describes how it can be applied to ensure forwarding to all
reachable destinations in case of any two or more link or node
failures in the network. After simulating with NS2 contains lot of
samples proved that the proposed protocol achieves exceptional
concert even under elevated node mobility using Trustworthy link
Failure Recovery Algorithm.
Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: This paper discusses the forensic investigation of a
fatality-involved catastrophic structure collapse and the special
challenges faced when tasked with directing such an effort. While
this paper discusses the investigation’s findings and the outcome of
the event; this paper’s primary focus is on the challenges faced
directing a forensic investigation that requires coordinating with
governmental oversight while also having to accommodate multiple
parties’ investigative teams. In particular the challenges discussed
within this paper included maintaining on-site safety and operations
while accommodating outside investigator’s interests. In addition this
paper discusses unique challenges that one may face such as what to
do about unethical conduct of interested party’s investigative teams,
“off the record” sharing of information, and clandestinely transmitted
evidence.
Abstract: This paper pioneers Care Robot Impact Assessment
(CRIA), a methodology used to identify, analyze, mitigate and
eliminate the risks posed by the insertion of non-medical personal
care robots (PCR) in medical care facilities. Its precedent instruments
[Privacy and Surveillance Impact Assessment (PIA and SIA)] fall
behind in coping with robots. Indeed, personal care robots change
dramatically how care is delivered. The paper presents a specific
risk-sector methodology, identifies which robots are under its scope
and presents some of the challenges introduced by these robots.
Abstract: The problem of finding control laws for underactuated
systems has attracted growing attention since these systems are
characterized by the fact that they have fewer actuators than the
degrees of freedom to be controlled. The acrobot, which is a planar
two-link robotic arm in the vertical plane with an actuator at the elbow
but no actuator at the shoulder, is a representative in underactuated
systems. In this paper, the dynamic model of the acrobot is
implemented using Mathworks’ Simscape. And the sliding mode
control is constructed using MATLAB and Simulink.
Abstract: Atmospheric carbon dioxide emissions are considered
as the greatest environmental challenge the world is facing today.
The tasks to control the emissions include the recovery of CO2 from
flue gas. This concern has been improved due to recent advances in
materials process engineering resulting in the development of
inorganic gas separation membranes with excellent thermal and
mechanical stability required for most gas separations. This paper,
therefore, evaluates the performance of a highly selective inorganic
membrane for CO2 recovery applications. Analysis of results
obtained is in agreement with experimental literature data. Further
results show the prediction performance of the membranes for gas
separation and the future direction of research. The materials
selection and the membrane preparation techniques are discussed.
Method of improving the interface defects in the membrane and its
effect on the separation performance has also been reviewed and in
addition advances to totally exploit the potential usage of this
innovative membrane.
Abstract: In this paper, the dependence of soliton pulses with
respect to phase in a 10Gbps, single channel, dispersion
uncompensated telecommunication system was studied. The
characteristic feature of periodic soliton interaction was noted at the
Interaction point (I=6202.5Km) in one collision length of L=12405.1
Km. The interaction point is located for 10Gbps system with an
initial relative spacing (qo) of soliton as 5.28 using Perturbation
theory. It is shown that, when two in-phase solitons are launched,
they interact at the point I=6202.5 Km, but the interaction could be
restricted with introduction of different phase initially. When the
phase of the input solitons increases, the deviation of soliton pulses at
the ‘I’ also increases. We have successfully demonstrated this effect
in a telecommunication set-up in terms of Quality factor (Q), where
the Q=0 for in-phase soliton. The Q was noted to be 125.9, 38.63,
47.53, 59.60, 161.37, and 78.04 for different phases such as 10o, 20o,
30o, 45o, 60o and 90o degrees respectively at Interaction point (I).
Abstract: Community integration is a construct that an
increasing body of research has shown to have a significant impact
on the wellbeing and recovery of people with psychiatric problems.
However, there are few studies that explore which factors can be
associated and predict community integration. Moreover, community
integration has been mostly studied in minority groups, and current
literature on the definition and manifestation of community
integration in the general population is scarcer. Thus, the current
study aims to characterize community integration and explore
possible predictor variables in a sample of participants with
psychiatric problems (PP, N=183) and a sample of participants from
the general population (GP, N=211).
Results show that people with psychiatric problems present above
average values of community integration, but are significantly lower
than their healthy counterparts. It was also possible to observe that
community integration does not vary in terms of the sociodemographic
characteristics of both groups in this study. Correlation
and multiple regression showed that, among several variables that
literature present as relevant in the community integration process,
only three variables emerged as having the most explanatory value in
community integration of both groups: sense of community, basic
needs satisfaction and submission. These results also shown that
those variables have increased explanatory power in the PP sample,
which leads us to emphasize the need to address this issue in future
studies and increase the understanding of the factors that can be
involved in the promotion of community integration, in order to
devise more effective interventions in this field.
Abstract: Paranoid ideation is a common thought process that
constitutes a defense against perceived social threats. The current
study aimed at the characterization of paranoid ideation in youths and
to explore the possible predictors involved in the development of
paranoid ideations. Paranoid ideation, shame, submission, early
childhood memories and current depressive, anxious and stress
symptomatology were assessed in a sample of 1516 Portuguese
youths. Higher frequencies of paranoid ideation were observed,
particularly in females and youths from lower socioeconomic status.
The main predictors identified relates to submissive behaviors and
adverse childhood experiences, and especially to shame feelings. The
current study emphasizes that the these predictors are similar to
findings in adults and clinical populations, and future implications to
research and clinical practice aiming at paranoid ideations are
discussed, as well as the pertinence of the study of mediating factors
that allow a wider understanding of this thought process in younger
populations and the prevention of psychopathology in adulthood.
Abstract: WO3/SiO2 catalysts were modified by an ion exchange
method with sodium hydroxide or potassium hydroxide solution. The
performance of the modified catalysts was tested in the metathesis of
ethylene and trans-2-butene to propylene. During ion exchange,
sodium and potassium ions played different roles. Sodium modified
catalysts revealed constant trans-2-butene conversion and propylene
selectivity when the concentrations of sodium in the solution were
varied. In contrast, potassium modified catalysts showed reduction of
the conversion and increase of the selectivity. From these results,
potassium hydroxide may affect the transformation of tungsten oxide
active species, resulting in the decrease in conversion whereas
sodium hydroxide did not. Moreover, the modification of catalysts by
this method improved the catalyst stability by lowering the amount of
coke deposited on the catalyst surface.
Abstract: This article presents our prototype MASET (Multi
Agents System for E-Tutoring Learners engaged in online
collaborative work). MASET that we propose is a system which
basically aims to help tutors in monitoring the collaborative work of
students and their various interactions. The evaluation of such
interactions by the tutor is based on the results provided by the
automatic analysis of the interaction indicators. This system is
predicated upon the middleware JADE (Java Agent Development
Framework) and e-learning Moodle platform. The MASET
environment is modeled by AUML which allows structuring the
different interactions between agents for the fulfillment and
performance of online collaborative work. This multi-agent system
has been the subject of a practical experimentation based on the
interactions data between Master Computer Engineering and System
students.