Abstract: Severe heart failure is a common problem that has a significant effect on health expenditures in industrialized countries; moreover it reduces patient-s quality of life. However, current research usually focuses either on detailed modeling of the heart or on detailed modeling of the cardiovascular system. Thus, this paper aims to present a sophisticated model of the heart enhanced with an extensive model of the cardiovascular system. Special interest is on the pressure and flow values close to the heart since these values are critical to accurately diagnose causes of heart failure. The model is implemented in Dymola an object-oriented, physical modeling language. Results achieved with the novel model show overall feasibility of the approach. Moreover, results are illustrated and compared to other models. The novel model shows significant improvements.
Abstract: This study presents energy saving in general-purpose
pumps widely used in industrial applications. Such pumps are
normally driven by a constant-speed electrical motor which in most
applications must support varying load conditions. This is equivalent
to saying the loading conditions mismatch the designed optimal
energy consumption requirements of the intended application thus
resulting in substantial energy losses. In the held experiments it was
indicated that combination of mechanical and electrical speed drives
can contribute to lower energy consumption in the pump without
negatively distorting the required performance indices of a typical
centrifugal pump at substantially lower energy consumption. The
registered energy savings were recorded to be within the 15-40%
margin. It was also indicated that although VSDs are installed at a
cost, the financial burden is balanced against the earnings resulting
from the associated energy savings.
Abstract: There are multiple ways to implement a decimator
filter. This paper addresses usage of CIC (cascaded-integrator-comb)
filter and HB (half band) filter as the decimator filter to reduce the
frequency sample rate by factor of 64 and detail of the
implementation step to realize this design in hardware. Low power
design approach for CIC filter and half band filter will be discussed.
The filter design is implemented through MATLAB system
modeling, ASIC (application specific integrated circuit) design flow
and verified using a FPGA (field programmable gate array) board
and MATLAB analysis.
Abstract: Increasing user comfort and reducing operation costs
have always been primary objectives of lighting control strategies in a
building. This paper proposes an architecture of the lighting control
system for a daylit office. The system consists of the lighting
controller, A/D & D/A converter, dimmable LED lights, and the
lighting management software. Verification tests are conducted using
the proposed system specialized for the interior lighting of a open-plan
office. The results showed the proposed architecture of the lighting
system would improve the overall system reliability, lower the system
cost, and provide ease of installation and maintenance.
Abstract: In this paper, we consider a two-neuron system with time-delayed connections between neurons. By analyzing the associated characteristic transcendental equation, its linear stability is investigated and Hopf bifurcation is demonstrated. Some explicit formulae for determining the stability and the direction of the Hopf bifurcation periodic solutions bifurcating from Hopf bifurcations are obtained by using the normal form theory and center manifold theory. Some numerical simulation results are given to support the theoretical predictions. Finally, main conclusions are given.
Abstract: Severe acute respiratory syndrome (SARS) is a respiratory disease in humans which is caused by the SARS coronavirus. The treatment of coronavirus-associated SARS has been evolving and so far there is no consensus on an optimal regimen. The mainstream therapeutic interventions for SARS involve broad-spectrum antibiotics and supportive care, as well as antiviral agents and immunomodulatory therapy. The Protein- Ligand interaction plays a significant role in structural based drug designing. In the present work we have taken the receptor Angiotensin converting enzyme 2 and identified the drugs that are commonly used against SARS. They are Lopinavir, Ritonavir, Ribavirin, and Oseltamivir. The receptor Angiotensin converting enzyme 2 (ACE-2) was docked with above said drugs and the energy value obtained are as follows, Lopinavir (-292.3), Ritonavir (-325.6), Oseltamivir (- 229.1), Ribavirin (-208.8). Depending on the least energy value we have chosen the best two drugs out of the four conventional drugs. We tried to improve the binding efficiency and steric compatibility of the two drugs namely Ritonavir and Lopinavir. Several modifications were made to the probable functional groups (phenylic, ketonic groups in case of Ritonavir and carboxylic groups in case of Lopinavir respectively) which were interacting with the receptor molecule. Analogs were prepared by Marvin Sketch software and were docked using HEX docking software. Lopinavir analog 8 and Ritonavir analog 11 were detected with significant energy values and are probable lead molecule. It infers that some of the modified drugs are better than the original drugs. Further work can be carried out to improve the steric compatibility of the drug based upon the work done above for a more energy efficient binding of the drugs to the receptor.
Abstract: A new reverse phase-high performance liquid chromatography (RP-HPLC) method with fluorescent detector (FLD) was developed and optimized for Norfloxacin determination in human plasma. Mobile phase specifications, extraction method and excitation and emission wavelengths were varied for optimization. HPLC system contained a reverse phase C18 (5 μm, 4.6 mm×150 mm) column with FLD operated at excitation 330 nm and emission 440 nm. The optimized mobile phase consisted of 14% acetonitrile in buffer solution. The aqueous phase was prepared by mixing 2g of citric acid, 2g sodium acetate and 1 ml of triethylamine in 1 L of Milli-Q water was run at a flow rate of 1.2 mL/min. The standard curve was linear for the range tested (0.156–20 μg/mL) and the coefficient of determination was 0.9978. Aceclofenac sodium was used as internal standard. A detection limit of 0.078 μg/mL was achieved. Run time was set at 10 minutes because retention time of norfloxacin was 0.99 min. which shows the rapidness of this method of analysis. The present assay showed good accuracy, precision and sensitivity for Norfloxacin determination in human plasma with a new internal standard and can be applied pharmacokinetic evaluation of Norfloxacin tablets after oral administration in human.
Abstract: The Time-Domain Boundary Element Method (TDBEM)
is a well known numerical technique that handles quite
properly dynamic analyses considering infinite dimension media.
However, when these analyses are also related to nonlinear behavior,
very complex numerical procedures arise considering the TD-BEM,
which may turn its application prohibitive. In order to avoid this
drawback and model nonlinear infinite media, the present work
couples two BEM formulations, aiming to achieve the best of two
worlds. In this context, the regions expected to behave nonlinearly
are discretized by the Domain Boundary Element Method (D-BEM),
which has a simpler mathematical formulation but is unable to deal
with infinite domain analyses; the TD-BEM is employed as in the
sense of an effective non-reflexive boundary. An iterative procedure
is considered for the coupling of the TD-BEM and D-BEM, which is
based on a relaxed renew of the variables at the common interfaces.
Elastoplastic models are focused and different time-steps are allowed
to be considered by each BEM formulation in the coupled analysis.
Abstract: The development of wireless communication technologies has changed our living style in global level. After the international success of mobile telephony standards, the location and time independent voice connection has become a default method in daily telecommunications. As for today, highly advanced multimedia messaging plays a key role in value added service handling. Along with evolving data services, the need for more complex applications can be seen, including the mobile usage of broadcast technologies. Here performance of a system design for terrestrial multimedia content is examined with emphasis on mobile reception. This review paper has accommodated the understanding of physical layer role and the flavour of terrestrial channel effects on the terrestrial multimedia transmission using OFDM keeping DVB-H as benchmark standard.
Abstract: In this paper, we introduce an mobile agent framework
with proactive load balancing for ambient intelligence (AmI) environments.
One of the main obstacles of AmI is the scalability in
which the openness of AmI environment introduces dynamic resource
requirements on agencies. To mediate this scalability problem, our
framework proposes a load balancing module to proactively analyze
the resource consumption of network bandwidth and preferred agencies
to suggest the optimal communication method to its user. The
framework generally formulates an AmI environment that consists
of three main components: (1) mobile devices, (2) hosts or agencies,
and (3) directory service center (DSC). A preliminary implementation
was conducted with NetLogo and the experimental results show that
the proposed approach provides enhanced system performance by
minimizing the network utilization to provide users with responsive
services.
Abstract: Reducing energy consumption of embedded systems requires careful memory management. It has been shown that Scratch- Pad Memories (SPMs) are low size, low cost, efficient (i.e. energy saving) data structures directly managed at the software level. In this paper, the focus is on heuristic methods for SPMs management. A method is efficient if the number of accesses to SPM is as large as possible and if all available space (i.e. bits) is used. A Tabu Search (TS) approach for memory management is proposed which is, to the best of our knowledge, a new original alternative to the best known existing heuristic (BEH). In fact, experimentations performed on benchmarks show that the Tabu Search method is as efficient as BEH (in terms of energy consumption) but BEH requires a sorting which can be computationally expensive for a large amount of data. TS is easy to implement and since no sorting is necessary, unlike BEH, the corresponding sorting time is saved. In addition to that, in a dynamic perspective where the maximum capacity of the SPM is not known in advance, the TS heuristic will perform better than BEH.
Abstract: Textile structures are engineered and fabricated to
meet worldwide structural applications. Nevertheless, research
varying textile structure on natural fibre as composite reinforcement
was found to be very limited. Most of the research is focusing on
short fibre and random discontinuous orientation of the reinforcement
structure. Realizing that natural fibre (NF) composite had been
widely developed to be used as synthetic fibre composite
replacement, this research attempted to examine the influence of
woven and cross-ply laminated structure towards its mechanical
performances. Laminated natural fibre composites were developed
using hand lay-up and vacuum bagging technique. Impact and
flexural strength were investigated as a function of fibre type (coir
and kenaf) and reinforcement structure (imbalanced plain woven,
0°/90° cross-ply and +45°/-45° cross-ply). Multi-level full factorial
design of experiment (DOE) and analysis of variance (ANOVA) was
employed to impart data as to how fibre type and reinforcement
structure parameters affect the mechanical properties of the
composites. This systematic experimentation has led to determination
of significant factors that predominant influences the impact and
flexural properties of the textile composites. It was proven that both
fibre type and reinforcement structure demonstrated significant
difference results. Overall results indicated that coir composite and
woven structure exhibited better impact and flexural strength. Yet,
cross-ply composite structure demonstrated better fracture resistance.
Abstract: In this article, we discuss project-based learning in the context of a wheel garden as an instructional tool in science and mathematics education. A wheel garden provides multiple opportunities to teach across the curriculum, to integrate disciplines, and to promote community involvement. Grounded in the theoretical framework of constructivism, the wheel garden provides a multidisciplined educational tool that provides a hands-on, non-traditional arena for learning. We will examine some of the cultural, art, science, and mathematics connections made with this project.
Abstract: This paper presents an algorithm of particle swarm
optimization with reduction for global optimization problems. Particle
swarm optimization is an algorithm which refers to the collective
motion such as birds or fishes, and a multi-point search algorithm
which finds a best solution using multiple particles. Particle
swarm optimization is so flexible that it can adapt to a number
of optimization problems. When an objective function has a lot of
local minimums complicatedly, the particle may fall into a local
minimum. For avoiding the local minimum, a number of particles are
initially prepared and their positions are updated by particle swarm
optimization. Particles sequentially reduce to reach a predetermined
number of them grounded in evaluation value and particle swarm
optimization continues until the termination condition is met. In order
to show the effectiveness of the proposed algorithm, we examine the
minimum by using test functions compared to existing algorithms.
Furthermore the influence of best value on the initial number of
particles for our algorithm is discussed.
Abstract: The paper explores the development of an optimization of method and apparatus for retrieving extended high dynamic range from digital negative image. Architectural photo imaging can benefit from high dynamic range imaging (HDRI) technique for preserving and presenting sufficient luminance in the shadow and highlight clipping image areas. The HDRI technique that requires multiple exposure images as the source of HDRI rendering may not be effective in terms of time efficiency during the acquisition process and post-processing stage, considering it has numerous potential imaging variables and technical limitations during the multiple exposure process. This paper explores an experimental method and apparatus that aims to expand the dynamic range from digital negative image in HDRI environment. The method and apparatus explored is based on a single source of RAW image acquisition for the use of HDRI post-processing. It will cater the optimization in order to avoid and minimize the conventional HDRI photographic errors caused by different physical conditions during the photographing process and the misalignment of multiple exposed image sequences. The study observes the characteristics and capabilities of RAW image format as digital negative used for the retrieval of extended high dynamic range process in HDRI environment.
Abstract: Program slicing is the task of finding all statements in
a program that directly or indirectly influence the value of a variable
occurrence. The set of statements that can affect the value of a
variable at some point in a program is called a program backward
slice. In several software engineering applications, such as program
debugging and measuring program cohesion and parallelism, several
slices are computed at different program points. The existing
algorithms for computing program slices are introduced to compute a
slice at a program point. In these algorithms, the program, or the
model that represents the program, is traversed completely or
partially once. To compute more than one slice, the same algorithm
is applied for every point of interest in the program. Thus, the same
program, or program representation, is traversed several times.
In this paper, an algorithm is introduced to compute all forward
static slices of a computer program by traversing the program
representation graph once. Therefore, the introduced algorithm is
useful for software engineering applications that require computing
program slices at different points of a program. The program
representation graph used in this paper is called Program Dependence
Graph (PDG).
Abstract: one of the significant factors for improving the
accuracy of Land Surface Temperature (LST) retrieval is the correct
understanding of the directional anisotropy for thermal radiance. In
this paper, the multiple scattering effect between heterogeneous
non-isothermal surfaces is described rigorously according to the
concept of configuration factor, based on which a directional thermal
radiance model is built, and the directional radiant character for urban
canopy is analyzed. The model is applied to a simple urban canopy
with row structure to simulate the change of Directional Brightness
Temperature (DBT). The results show that the DBT is aggrandized
because of the multiple scattering effects, whereas the change range of
DBT is smoothed. The temperature difference, spatial distribution,
emissivity of the components can all lead to the change of DBT. The
“hot spot" phenomenon occurs when the proportion of high
temperature component in the vision field came to a head. On the other
hand, the “cool spot" phenomena occur when low temperature
proportion came to the head. The “spot" effect disappears only when
the proportion of every component keeps invariability. The model
built in this paper can be used for the study of directional effect on
emissivity, the LST retrieval over urban areas and the adjacency effect
of thermal remote sensing pixels.
Abstract: In this study, an inland metropolitan area, Gwangju, in Korea was selected to assess the amplification potential of earthquake motion and provide the information for regional seismic countermeasure. A geographic information system-based expert system was implemented for reliably predicting the spatial geotechnical layers in the entire region of interesting by building a geo-knowledge database. Particularly, the database consists of the existing boring data gathered from the prior geotechnical projects and the surface geo-knowledge data acquired from the site visit. For practical application of the geo-knowledge database to estimate the earthquake hazard potential related to site amplification effects at the study area, seismic zoning maps on geotechnical parameters, such as the bedrock depth and the site period, were created within GIS framework. In addition, seismic zonation of site classification was also performed to determine the site amplification coefficients for seismic design at any site in the study area. KeywordsEarthquake hazard, geo-knowledge, geographic information system, seismic zonation, site period.
Abstract: Problem-based learning (PBL) is one of the student
centered approaches and has been considered by a number of higher
educational institutions in many parts of the world as a method of
delivery. This paper presents a creative thinking approach for
implementing Problem-based Learning in Mechanics of Structure
within a Malaysian Polytechnics environment. In the learning
process, students learn how to analyze the problem given among the
students and sharing classroom knowledge into practice. Further,
through this course-s emphasis on problem-based learning, students
acquire creative thinking skills and professional skills as they tackle
complex, interdisciplinary and real-situation problems. Once the
creative ideas are generated, there are useful additional techniques
for tender ideas that will grow into a productive concept or solution.
The combination of creative skills and technical abilities will enable
the students to be ready to “hit-the-ground-running" and produce in
industry when they graduate.
Abstract: Three-dimensional geometric models have been used
to present architectural and engineering works, showing their final
configuration. When the clarification of a detail or the constitution of
a construction step in needed, these models are not appropriate. They
do not allow the observation of the construction progress of a
building. Models that could present dynamically changes of the
building geometry are a good support to the elaboration of projects.
Techniques of geometric modeling and virtual reality were used to
obtain models that could visually simulate the construction activity.
The applications explain the construction work of a cavity wall and a
bridge. These models allow the visualization of the physical
progression of the work following a planned construction sequence,
the observation of details of the form of every component of the
works and support the study of the type and method of operation of
the equipment applied in the construction. These models presented
distinct advantage as educational aids in first-degree courses in Civil
Engineering. The use of Virtual Reality techniques in the
development of educational applications brings new perspectives to
the teaching of subjects related to the field of civil construction.