Abstract: The ability of agricultural and decorative plants to
absorb and detoxify TNT and RDX has been studied. All tested 8
plants, grown hydroponically, were able to absorb these explosives
from water solutions: Alfalfa > Soybean > Chickpea> Chikling vetch
>Ryegrass > Mung bean> China bean > Maize. Differently from
TNT, RDX did not exhibit negative influence on seed germination
and plant growth. Moreover, some plants, exposed to RDX
containing solution were increased in their biomass by 20%. Study of
the fate of absorbed [1-14ðí]-TNT revealed the label distribution in
low and high-molecular mass compounds, both in roots and above
ground parts of plants, prevailing in the later. Content of 14ðí in lowmolecular
compounds in plant roots are much higher than in above
ground parts. On the contrary, high-molecular compounds are more
intensively labeled in aboveground parts of soybean. Most part (up to
70%) of metabolites of TNT, formed either by enzymatic reduction
or oxidation, is found in high molecular insoluble conjugates.
Activation of enzymes, responsible for reduction, oxidation and
conjugation of TNT, such as nitroreductase, peroxidase,
phenoloxidase and glutathione S-transferase has been demonstrated.
Among these enzymes, only nitroreductase was shown to be induced
in alfalfa, exposed to RDX. The increase in malate dehydrogenase
activities in plants, exposed to both explosives, indicates
intensification of Tricarboxylic Acid Cycle, that generates reduced
equivalents of NAD(P)H, necessary for functioning of the
nitroreductase. The hypothetic scheme of TNT metabolism in plants
is proposed.
Abstract: Structured catalysts formed from the growth of
zeolites on substrates is an area of increasing interest due to the
increased efficiency of the catalytic process, and the ability to
provide superior heat transfer and thermal conductivity for both
exothermic and endothermic processes.
However, the generation of structured catalysts represents a
significant challenge when balancing the relationship variables
between materials properties and catalytic performance, with the
Na2O, H2O and Al2O3 gel composition paying a significant role in
this dynamic, thereby affecting the both the type and range of
application.
The structured catalyst films generated as part of this
investigation have been characterised using a range of techniques,
including X-ray diffraction (XRD), Electron microscopy (SEM),
Energy Dispersive X-ray analysis (EDX) and Thermogravimetric
Analysis (TGA), with the transition from oxide-on-alloy wires to
hydrothermally synthesised uniformly zeolite coated surfaces being
demonstrated using both SEM and XRD. The robustness of the
coatings has been ascertained by subjecting these to thermal cycling
(ambient to 550oC), with the results indicating that the synthesis time
and gel compositions have a crucial effect on the quality of zeolite
growth on the FeCrAlloy wires.
Finally, the activity of the structured catalyst was verified by a
series of comparison experiments with standard zeolite Y catalysts in
powdered pelleted forms.
Abstract: This paper deals with modeling and parameter
identification of nonlinear systems described by Hammerstein model
having Piecewise nonlinear characteristics such as Dead-zone
nonlinearity characteristic. The simultaneous use of both an easy
decomposition technique and the triangular basis functions leads to a
particular form of Hammerstein model. The approximation by using
Triangular basis functions for the description of the static nonlinear
block conducts to a linear regressor model, so that least squares
techniques can be used for the parameter estimation. Singular Values
Decomposition (SVD) technique has been applied to separate the
coupled parameters. The proposed approach has been efficiently
tested on academic examples of simulation.
Abstract: This paper presents the comparative study of coded
data methods for finding the benefit of concealing the natural data
which is the mercantile secret. Influential parameters of the number
of replicates (rep), treatment effects (τ) and standard deviation (σ)
against the efficiency of each transformation method are investigated.
The experimental data are generated via computer simulations under
the specified condition of the process with the completely
randomized design (CRD). Three ways of data transformation consist
of Box-Cox, arcsine and logit methods. The difference values of F
statistic between coded data and natural data (Fc-Fn) and hypothesis
testing results were determined. The experimental results indicate
that the Box-Cox results are significantly different from natural data
in cases of smaller levels of replicates and seem to be improper when
the parameter of minus lambda has been assigned. On the other hand,
arcsine and logit transformations are more robust and obviously,
provide more precise numerical results. In addition, the alternate
ways to select the lambda in the power transformation are also
offered to achieve much more appropriate outcomes.
Abstract: An overview of the important aspects of managing
and controlling industrial effluent discharges to public sewers namely
sampling, characterization, quantification and legislative controls has
been presented. The findings have been validated by means of a case
study covering three industrial sectors namely, tanning, textile
finishing and food processing industries. Industrial effluents
discharges were found to be best monitored by systematic and
automatic sampling and quantified using water meter readings
corrected for evaporative and consumptive losses. Based on the
treatment processes employed in the public owned treatment works
and the chemical oxygen demand and biochemical oxygen demand
levels obtained, the effluent from all the three industrial sectors
studied were found to lie in the toxic zone. Thus, physico-chemical
treatment of these effluents is required to bring them into the
biodegradable zone. KL values (quoted to base e) were greater than
0.50 day-1 compared to 0.39 day-1 for typical municipality
wastewater.
Abstract: In this paper we will develop a sequential life test approach applied to a modified low alloy-high strength steel part used in highway overpasses in Brazil.We will consider two possible underlying sampling distributions: the Normal and theInverse Weibull models. The minimum life will be considered equal to zero. We will use the two underlying models to analyze a fatigue life test situation, comparing the results obtained from both.Since a major chemical component of this low alloy-high strength steel part has been changed, there is little information available about the possible values that the parameters of the corresponding Normal and Inverse Weibull underlying sampling distributions could have. To estimate the shape and the scale parameters of these two sampling models we will use a maximum likelihood approach for censored failure data. We will also develop a truncation mechanism for the Inverse Weibull and Normal models. We will provide rules to truncate a sequential life testing situation making one of the two possible decisions at the moment of truncation; that is, accept or reject the null hypothesis H0. An example will develop the proposed truncated sequential life testing approach for the Inverse Weibull and Normal models.
Abstract: Over the years, there is a growing trend towards
quality-based specifications in highway construction. In many
Quality Control/Quality Assurance (QC/QA) specifications, the
contractor is primarily responsible for quality control of the process,
whereas the highway agency is responsible for testing the acceptance
of the product. A cooperative investigation was conducted in Illinois
over several years to develop a prototype End-Result Specification
(ERS) for asphalt pavement construction. The final characteristics of
the product are stipulated in the ERS and the contractor is given
considerable freedom in achieving those characteristics. The risk for
the contractor or agency depends on how the acceptance limits and
processes are specified. Stochastic simulation models are very useful
in estimating and analyzing payment risk in ERS systems and these
form an integral part of the Illinois-s prototype ERS system. This
paper describes the development of an innovative methodology to
estimate the variability components in in-situ density, air voids and
asphalt content data from ERS projects. The information gained from
this would be crucial in simulating these ERS projects for estimation
and analysis of payment risks associated with asphalt pavement
construction. However, these methods require at least two parties to
conduct tests on all the split samples obtained according to the
sampling scheme prescribed in present ERS implemented in Illinois.
Abstract: A key element of many distribution systems is the
routing and scheduling of vehicles servicing a set of customers. A
wide variety of exact and approximate algorithms have been
proposed for solving the vehicle routing problems (VRP). Exact
algorithms can only solve relatively small problems of VRP, which is
classified as NP-Hard. Several approximate algorithms have proven
successful in finding a feasible solution not necessarily optimum.
Although different parts of the problem are stochastic in nature; yet,
limited work relevant to the application of discrete event system
simulation has addressed the problem. Presented here is optimization
using simulation of VRP; where, a simplified problem has been
developed in the ExtendSimTM simulation environment; where,
ExtendSimTM evolutionary optimizer is used to minimize the total
transportation cost of the problem. Results obtained from the model
are very satisfactory. Further complexities of the problem are
proposed for consideration in the future.
Abstract: Aim of this paper is to explore the prospect of a new approach of mobile phone banking in Libya. This study evaluates customer knowledge on commercial mobile banking in Libya. To examine the relationship between age, occupation and intention for using mobile banking for commercial purpose, a survey was conducted to gather information from one hundred Libyan bank clients. The results indicate that Libyan customers have accepted the new technology and they are ready to use it. There is no significant joint relationship between age and occupation found in intention to use mobile banking in Libya. On the other hand, the customers’ knowledge about mobile banking has a greater relationship with the intention. This study has implications for demographic researches and consumer behaviour disciplines. It also has profitable implications for banks and managers in Libya, as it will assist in better understanding of the Libyan consumers and their activities, when they develop their market strategies and new service.
Abstract: Sonogram images of normal and lymphocyte thyroid tissues have considerable overlap which makes it difficult to interpret and distinguish. Classification from sonogram images of thyroid gland is tackled in semiautomatic way. While making manual diagnosis from images, some relevant information need not to be recognized by human visual system. Quantitative image analysis could be helpful to manual diagnostic process so far done by physician. Two classes are considered: normal tissue and chronic lymphocyte thyroid (Hashimoto's Thyroid). Data structure is analyzed using K-nearest-neighbors classification. This paper is mentioned that unlike the wavelet sub bands' energy, histograms and Haralick features are not appropriate to distinguish between normal tissue and Hashimoto's thyroid.
Abstract: The Internet and the ever growing applications enable
communities to share and collaborate through common platforms.
However, this growing pattern is not witnessed yet even for elearning.
This paper is based on a doctoral research which aimed at
researching the ways students interact in an online campus and the
supports that they look for and require. Content analysis, based on the
Panchoo/Jaillet methodology, was done on four synchronous
meetings between a tutor and his ten students. The UNIV-Rct ecampus,
analogical to a physical campus, was found to be user
friendly and the students enrolled in a master-s course faced no
difficulties in using it. In addition to the environmental aspects, the
pedagogical implementation of the course has driven the students to
interact and collaborate significantly and this has contributed to
overcome the problems faced by the distance learners. This
completely online model was found to be fruitful in helping distant
learners fight their loneliness and brave their difficulties in a socioconstructivism
approach.
Abstract: A robust control approach is proposed for a high speed manipulator using a hybrid computed torque control approach in the state space. The high-speed manipulator is driven by permanent magnet dc motors to track a trajectory in the joint space in the presence of disturbances. Tracking problem is analyzed in the state space where the completed models are considered for actuators. The proposed control approach can guarantee the stability and a satisfactory tracking performance. A two-link elbow manipulator driven by electrical actuators is simulated and results are shown to satisfy conditions under technical specifications.
Abstract: This paper aims to present a framework for the
organizational knowledge management, which seeks to deploy a
standardized structure for the integrated management of knowledge is
a common language based on domains, processes and global
indicators inspired by the COBIT framework 5 (ISACA, 2012),
which supports the integration of three technologies, enterprise
information architecture (EIA), the business process modeling (BPM)
and service-oriented architecture (SOA). The Gomak Framework is a
management platform that seeks to integrate the information
technology infrastructure, the structure of applications, information
infrastructure, and business logic and business model to support a
sound strategy of organizational knowledge management, low
process-based approach and concurrent engineering. Concurrent
engineering (CE) is a systematic approach to integrated product
development that respond to customer expectations, involving all
perspectives in parallel, from the beginning of the product life cycle.
(European Space Agency, 2000).
Abstract: This paper describes the development of a fully
automated measurement software for antenna radiation pattern
measurements in a Compact Antenna Test Range (CATR). The
CATR has a frequency range from 2-40 GHz and the measurement
hardware includes a Network Analyzer for transmitting and
Receiving the microwave signal and a Positioner controller to control
the motion of the Styrofoam column. The measurement process
includes Calibration of CATR with a Standard Gain Horn (SGH)
antenna followed by Gain versus angle measurement of the Antenna
under test (AUT). The software is designed to control a variety of
microwave transmitter / receiver and two axis Positioner controllers
through the standard General Purpose interface bus (GPIB) interface.
Addition of new Network Analyzers is supported through a slight
modification of hardware control module. Time-domain gating is
implemented to remove the unwanted signals and get the isolated
response of AUT. The gated response of the AUT is compared with
the calibration data in the frequency domain to obtain the desired
results. The data acquisition and processing is implemented in
Agilent VEE and Matlab. A variety of experimental measurements
with SGH antennas were performed to validate the accuracy of
software. A comparison of results with existing commercial
softwares is presented and the measured results are found to be
within .2 dBm.
Abstract: The drastic increase in the usage of SMS technology
has led service providers to seek for a solution that enable users of
mobile devices to access services through SMSs. This has resulted in
the proposal of solutions towards SMS-based service invocation in
service oriented environments. However, the dynamic nature of
service-oriented environments coupled with sudden load peaks
generated by service request, poses performance challenges to
infrastructures for supporting SMS-based service invocation. To
address this problem we adopt load balancing techniques. A load
balancing model with adaptive load balancing and load monitoring
mechanisms as its key constructs is proposed. The load balancing
model then led to realization of Least Loaded Load Balancing
Framework (LLLBF). Evaluation of LLLBF benchmarked with round
robin (RR) scheme on the queuing approach showed LLLBF
outperformed RR in terms of response time and throughput.
However, LLLBF achieved better result in the cost of high
processing power.
Abstract: In this work we present a solution for DAGC (Digital
Automatic Gain Control) in WLAN receivers compatible to IEEE 802.11a/g standard. Those standards define communication in 5/2.4
GHz band using Orthogonal Frequency Division Multiplexing OFDM modulation scheme. WLAN Transceiver that we have used
enables gain control over Low Noise Amplifier (LNA) and a
Variable Gain Amplifier (VGA). The control over those signals is
performed in our digital baseband processor using dedicated hardware block DAGC. DAGC in this process is used to automatically control the VGA and LNA in order to achieve better
signal-to-noise ratio, decrease FER (Frame Error Rate) and hold the
average power of the baseband signal close to the desired set point.
DAGC function in baseband processor is done in few steps: measuring power levels of baseband samples of an RF signal,accumulating the differences between the measured power level and
actual gain setting, adjusting a gain factor of the accumulation, and
applying the adjusted gain factor the baseband values. Based on the measurement results of RSSI signal dependence to input power we have concluded that this digital AGC can be implemented applying
the simple linearization of the RSSI. This solution is very simple but also effective and reduces complexity and power consumption of the
DAGC. This DAGC is implemented and tested both in FPGA and in ASIC as a part of our WLAN baseband processor. Finally, we have integrated this circuit in a compact WLAN PCMCIA board based on MAC and baseband ASIC chips designed from us.
Abstract: In recent years, it has been proposed security
architecture for sensor network.[2][4]. One of these, TinySec by Chris
Kalof, Naveen Sastry, David Wagner had proposed Link layer security
architecture, considering some problems of sensor network. (i.e :
energy, bandwidth, computation capability,etc). The TinySec employs
CBC_mode of encryption and CBC-MAC for authentication based on
SkipJack Block Cipher. Currently, This TinySec is incorporated in the
TinyOS for sensor network security.
This paper introduces TinyHash based on general hash algorithm.
TinyHash is the module in order to replace parts of authentication and
integrity in the TinySec. it implies that apply hash algorithm on
TinySec architecture. For compatibility about TinySec, Components
in TinyHash is constructed as similar structure of TinySec. And
TinyHash implements the HMAC component for authentication and
the Digest component for integrity of messages. Additionally, we
define the some interfaces for service associated with hash algorithm.
Abstract: Flow field around hypersonic vehicles is very
complex and difficult to simulate. The boundary layers are squeezed
between shock layer and body surface. Resolution of boundary layer,
shock wave and turbulent regions where the flow field has high
values is difficult of capture. Detached eddy simulation (DES) is a
modification of a RANS model in which the model switches to a
subgrid scale formulation in regions fine enough for LES
calculations. Regions near solid body boundaries and where the
turbulent length scale is less than the maximum grid dimension are
assigned the RANS mode of solution. As the turbulent length scale
exceeds the grid dimension, the regions are solved using the LES
mode. Therefore the grid resolution is not as demanding as pure LES,
thereby considerably cutting down the cost of the computation. In
this research study hypersonic flow is simulated at Mach 8 and
different angle of attacks to resolve the proper boundary layers and
discontinuities. The flow is also simulated in the long wake regions.
Mesh is little different than RANS simulations and it is made dense
near the boundary layers and in the wake regions to resolve it
properly. Hypersonic blunt cone cylinder body with frustrum at angle
5o and 10 o are simulated and there aerodynamics study is performed
to calculate aerodynamics characteristics of different geometries. The
results and then compared with experimental as well as with some
turbulence model (SA Model). The results achieved with DES
simulation have very good resolution as well as have excellent
agreement with experimental and available data. Unsteady
simulations are performed for DES calculations by using duel time
stepping method or implicit time stepping. The simulations are
performed at Mach number 8 and angle of attack from 0o to 10o for
all these cases. The results and resolutions for DES model found
much better than SA turbulence model.
Abstract: As is needless to say; a majority of accidents, which occur, are due to drunk driving. As such, there is no effective mechanism to prevent this. Here we have designed an integrated system for the same purpose. Alcohol content in the driver-s body is detected by means of an infrared breath analyzer placed at the steering wheel. An infrared cell directs infrared energy through the sample and any unabsorbed energy at the other side is detected. The higher the concentration of ethanol, the more infrared absorption occurs (in much the same way that a sunglass lens absorbs visible light, alcohol absorbs infrared light). Thus the alcohol level of the driver is continuously monitored and calibrated on a scale. When it exceeds a particular limit the fuel supply is cutoff. If the device is removed also, the fuel supply will be automatically cut off or an alarm is sounded depending upon the requirement. This does not happen abruptly and special indicators are fixed at the back to avoid inconvenience to other drivers using the highway signals. Frame work for integration of sensors and control module in a scalable multi-agent system is provided .A SMS which contains the current GPS location of the vehicle is sent via a GSM module to the police control room to alert the police. The system is foolproof and the driver cannot tamper with it easily. Thus it provides an effective and cost effective solution for the problem of drunk driving in vehicles.
Abstract: In this paper, a class of impulsive BAM fuzzy cellular neural networks with time delays in the leakage terms is formulated and investigated. By establishing a delay differential inequality and M-matrix theory, some sufficient conditions ensuring the existence, uniqueness and global exponential stability of equilibrium point for impulsive BAM fuzzy cellular neural networks with time delays in the leakage terms are obtained. In particular, a precise estimate of the exponential convergence rate is also provided, which depends on system parameters and impulsive perturbation intention. It is believed that these results are significant and useful for the design and applications of BAM fuzzy cellular neural networks. An example is given to show the effectiveness of the results obtained here.