Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: In the analysis of structures, the nonlinear effects due to large displacement, large rotation and materially-nonlinear are very important and must be considered for the reliable analysis. The non-linear fmite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of fmite element code using the standard Galerkin weighted residual formulation. Two-dimensional plane stress model was carried out to present the shear wall response. Total Lagangian formulation, which is computationally more effective, is used in the formulation of stiffness matrices and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The details of the program formulation are highlighted and the results of the analyses are presented, along with a comparison of the response of the structure with Ansys software results. The presented model in this paper can be developed for nonlinear analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: In the paper we presented the possibility of application
collagen gels with active principle-s from marine algae extract and chlorhexidine salt in dental medicine. The hydro-alcoholic extracts
from marine algae have been used as they have been obtained. The extracts from marine algae and chlorhexidine salt (digluconate) are
incorporated in type I non-denatured fibrillar collagen matrixes. In order to obtain therapeutic effects at nanostructure level, it is important to know the rheological characteristics of the relevant mixtures of collagen gels and extracts from marine algae selected for use. In this survey we have studied mixtures made of non-denatured
fibrillar collagen hydro-gels where different concentrations of marine
algae have been incorporated. Based on the data obtained for the
shearing tensions, we have traced the rheograms – the diagrams for shearing tensions depending on the shearing speed values – from
which we have calculated the apparent viscosities as ratios between shearing tension and speed values, which have been figured in
relation to the shearing speed values, with a view to levelling
dependency.
Abstract: This work presents a new algorithm based on a combination of fuzzy (FUZ), Dynamic Programming (DP), and Genetic Algorithm (GA) approach for capacitor allocation in distribution feeders. The problem formulation considers two distinct objectives related to total cost of power loss and total cost of capacitors including the purchase and installation costs. The novel formulation is a multi-objective and non-differentiable optimization problem. The proposed method of this article uses fuzzy reasoning for sitting of capacitors in radial distribution feeders, DP for sizing and finally GA for finding the optimum shape of membership functions which are used in fuzzy reasoning stage. The proposed method has been implemented in a software package and its effectiveness has been verified through a 9-bus radial distribution feeder for the sake of conclusions supports. A comparison has been done among the proposed method of this paper and similar methods in other research works that shows the effectiveness of the proposed method of this paper for solving optimum capacitor planning problem.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: Sensor network applications are often data centric and
involve collecting data from a set of sensor nodes to be delivered
to various consumers. Typically, nodes in a sensor network are
resource-constrained, and hence the algorithms operating in these
networks must be efficient. There may be several algorithms available
implementing the same service, and efficient considerations may
require a sensor application to choose the best suited algorithm. In
this paper, we present a systematic evaluation of a set of algorithms
implementing the data gathering service. We propose a modular
infrastructure for implementing such algorithms in TOSSIM with
separate configurable modules for various tasks such as interest
propagation, data propagation, aggregation, and path maintenance.
By appropriately configuring these modules, we propose a number
of data gathering algorithms, each of which incorporates a different
set of heuristics for optimizing performance. We have performed
comprehensive experiments to evaluate the effectiveness of these
heuristics, and we present results from our experimentation efforts.
Abstract: Content-based Image Retrieval (CBIR) aims at searching image databases for specific images that are similar to a given query image based on matching of features derived from the image content. This paper focuses on a low-dimensional color based indexing technique for achieving efficient and effective retrieval performance. In our approach, the color features are extracted using the mean shift algorithm, a robust clustering technique. Then the cluster (region) mode is used as representative of the image in 3-D color space. The feature descriptor consists of the representative color of a region and is indexed using a spatial indexing method that uses *R -tree thus avoiding the high-dimensional indexing problems associated with the traditional color histogram. Alternatively, the images in the database are clustered based on region feature similarity using Euclidian distance. Only representative (centroids) features of these clusters are indexed using *R -tree thus improving the efficiency. For similarity retrieval, each representative color in the query image or region is used independently to find regions containing that color. The results of these methods are compared. A JAVA based query engine supporting query-by- example is built to retrieve images by color.
Abstract: Integrative teaching methodology is based on
connecting and summarizing knowledge from different subjects in
order to create better understanding of different disciplines and
improvement of competences in general. Integrative teaching
methodology was implemented and realised during one academic
year in 17 Latvian schools according with specially worked out
programme by specialists of different fields for adaptation in social
environment of children and young people with learning, cognitive
functions and motor disorders. Implemented integrative teaching
methodology consisted from three subsections which were
specialised for adaptation in social environment, improvement of
cognitive functions and improvement and harmonization of
personality. The results of investigation showed that the use of
integrative teaching methodology is an effective way for
improvement of learning motivation and negotiation of learning
disorders of different age schoolchildren.
Abstract: Enzymatic hydrolysis of starch from natural sources
finds potential application in commercial production of alcoholic
beverage and bioethanol. In this study the effect of starch
concentration, temperature, time and enzyme concentration were
studied and optimized for hydrolysis of cassava (Manihot esculenta)
starch powder (of mesh 80/120) into glucose syrup by immobilized
(using Polyacrylamide gel) a-amylase using central composite
design. The experimental result on enzymatic hydrolysis of cassava
starch was subjected to multiple linear regression analysis using
MINITAB 14 software. Positive linear effect of starch concentration,
enzyme concentration and time was observed on hydrolysis of
cassava starch by a-amylase. The statistical significance of the model
was validated by F-test for analysis of variance (p < 0.01). The
optimum value of starch concentration temperature, time and enzyme
concentration were found to be 4.5% (w/v), 45oC, 150 min, and 1%
(w/v) enzyme. The maximum glucose yield at optimum condition
was 5.17 mg/mL.
Abstract: Optical burst switching (OBS) has been proposed to
realize the next generation Internet based on the wavelength division
multiplexing (WDM) network technologies. In the OBS, the burst
contention is one of the major problems. The deflection routing has
been designed for resolving the problem. However, the deflection
routing becomes difficult to prevent from the burst contentions as the
network load becomes high. In this paper, we introduce a flow rate
control methods to reduce burst contentions. We propose new flow
rate control methods based on the leaky bucket algorithm and
deflection routing, i.e. separate leaky bucket deflection method, and
dynamic leaky bucket deflection method. In proposed methods, edge
nodes which generate data bursts carry out the flow rate control
protocols. In order to verify the effectiveness of the flow rate control in
OBS networks, we show that the proposed methods improve the
network utilization and reduce the burst loss probability through
computer simulations.
Abstract: A study was undertaken to investigate the effect of
liquid nitrogen aeration on mortalities of adult Cryptolestes
furrugineus, rusty grain beetles, in a prototype cardboard grain bin
equipped with an aeration system. The grain bin was filled with Hard
Red Spring wheat and liquid nitrogen was introduced from the bottom
of the bin. The survival of both cold acclimated and unacclimated C.
furrugineus was tested. The study reveals that cold acclimated insects
had higher survival than unacclimated insects under similar cooling
conditions. In most cases, mortalities of as high as 100% were
achieved at the bottom 100 cm of the grain bin for unacclimated
insects for most of the trials. Insect survival increased as the distance
from the bottom of the grain bin increased. There was no adverse
effect of liquid nitrogen aeration on wheat germination.
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.
Abstract: The analysis of electromagnetic environment using
deterministic mathematical models is characterized by the
impossibility of analyzing a large number of interacting network
stations with a priori unknown parameters, and this is characteristic,
for example, of mobile wireless communication networks. One of the
tasks of the tools used in designing, planning and optimization of
mobile wireless network is to carry out simulation of electromagnetic
environment based on mathematical modelling methods, including
computer experiment, and to estimate its effect on radio
communication devices. This paper proposes the development of a
statistical model of electromagnetic environment of a mobile
wireless communication network by describing the parameters and
factors affecting it including the propagation channel and their
statistical models.
Abstract: in dissimilar material joints, failure often occurs
along the interface between two materials due to stress singularity.
Stress distribution and its concentration depend on materials and
geometry of the junction. Inhomogenity of stress distribution at the
interface of junction of two materials with different elastic modules
and stress concentration in this zone are the main factors resulting in
rupture of the junction. Effect of joining angle in the interface of
aluminum-polycarbonate will be discussed in this paper. Computer
simulation and finite element analysis by ABAQUS showed that
convex interfacial joint leads to stress reduction at junction corners in
compare with straight joint. This finding is confirmed by photoelastic
experimental results.
Abstract: Employees commitments of vision and mission of
organization is effected due to manager’s executes by approach of
leadership The leaders who have attributions like vision, confidence
and correctitude, sharing and participation, creativeness, progressive
learning –improvement and responsibility are effective to increase
organizational commitment if they are sensitive to expectation and
requirement of employees in an organization. Studies about
organizational commitment appear results that employees who have
strong organizational commitment have the most contribution. In this
study, “Leadership” and “Organizational Commitment” conduct
surveys to 31 employees of Ahmet Özdemir Nak. Tic. San. A.Ş.
which has operations in road and railway transportation sector. It is
analyzed the effects of leadership approach to organizational
commitment deals with result of survey.
Abstract: Cyber attacks pose a serious threat to all states. Therefore, states constantly seek for various methods to encounter those threats. In addition, recent changes in the nature of cyber attacks and their more complicated methods have created a new concept: active cyber defense (ACD). This article tries to answer firstly why ACD is important to NATO and find out the viewpoint of NATO towards ACD. Secondly, infrastructure protection is essential to cyber defense. Critical infrastructure protection with ACD means is even more important. It is assumed that by implementing active cyber defense, NATO may not only be able to repel the attacks but also be deterrent. Hence, the use of ACD has a direct positive effect in all international organizations’ future including NATO.
Abstract: In this paper, the backward Ussor iterative matrix is proposed. The relationship of convergence between the backward Ussor iterative matrix and Jacobi iterative matrix is obtained, which makes the results in the corresponding references be improved and refined.Moreover,numerical examples also illustrate the effectiveness of these conclusions.
Abstract: The article presents findings from the study and
analysis of the results of an experimental programme focused on the
production of concrete and fibre reinforced concrete in which natural
aggregate has been substituted with brick or concrete recyclate. The
research results are analyzed to monitor the effect of mechanicalphysical
characteristics on the durability properties of tested
cementitious composites. The key parts of the fibre reinforced
concrete mix are the basic components: aggregates – recyclate,
cement, fly ash, water and fibres. Their specific ratios and the
properties of individual components principally affect the resulting
behaviour of fresh fibre reinforced concrete and the characteristics of
the final product. The article builds on the sources dealing with the
use of recycled aggregates from construction and demolition waste in
the production of fibre reinforced concrete. The implemented
procedure of testing the composite contributes to the building
sustainability in environmental engineering.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: As the disfunctions of the information society and
social development progress, intrusion problems such as malicious
replies, spam mail, private information leakage, phishing, and
pharming, and side effects such as the spread of unwholesome
information and privacy invasion are becoming serious social
problems. Illegal access to information is also becoming a problem as
the exchange and sharing of information increases on the basis of the
extension of the communication network. On the other hand, as the
communication network has been constructed as an international,
global system, the legal response against invasion and cyber-attack
from abroad is facing its limit. In addition, in an environment where
the important infrastructures are managed and controlled on the basis
of the information communication network, such problems pose a
threat to national security. Countermeasures to such threats are
developed and implemented on a yearly basis to protect the major
infrastructures of information communication. As a part of such
measures, we have developed a methodology for assessing the
information protection level which can be used to establish the
quantitative object setting method required for the improvement of the
information protection level.