Abstract: This paper is devoted to predict laminar and turbulent
heating rates around blunt re-entry spacecraft at hypersonic
conditions. Heating calculation of a hypersonic body is normally
performed during the critical part of its flight trajectory. The
procedure is of an inverse method, where a shock wave is assumed,
and the body shape that supports this shock, as well as the flowfield
between the shock and body, are calculated. For simplicity the
normal momentum equation is replaced with a second order pressure
relation; this simplification significantly reduces computation time.
The geometries specified in this research, are parabola and ellipsoids
which may have conical after bodies. An excellent agreement is
observed between the results obtained in this paper and those
calculated by others- research. Since this method is much faster than
Navier-Stokes solutions, it can be used in preliminary design,
parametric study of hypersonic vehicles.
Abstract: A numerical study on the influence of forward-facing
cavity length upon forward-facing cavity and opposing jet combined
thermal protection system (TPS) cooling efficiency under hypersonic
flow is conducted, by means of which the flow field parameters, heat
flux distribution along the outer body surface are obtained. The
numerical simulation results are validated by experiments and the
cooling effect of the combined TPS with different cavity length is
analyzed. The numerical results show that the combined configuration
dose well in cooling the nose of the hypersonic vehicle. The deeper the
cavity is, the weaker the heat flux is. The recirculation region plays a
key role for the reduction of the aerodynamic heating.
Abstract: The malfunction of thermal protection system (TPS) caused by aerodynamic heating is a latent trouble to aircraft structure safety. Accurately predicting the structure temperature field is quite important for the TPS design of hypersonic vehicle. Since Thornton’s work in 1988, the coupled method of aerodynamic heating and heat transfer has developed rapidly. However, little attention has been paid to the influence of structural deformation on aerodynamic heating and structural temperature field. In the flight, especially the long-endurance flight, the structural deformation, caused by the aerodynamic heating and temperature rise, has a direct impact on the aerodynamic heating and structural temperature field. Thus, the coupled interaction cannot be neglected. In this paper, based on the method of static aero-thermo-elasticity, considering the influence of aero-thermo-elasticity deformation, the aerodynamic heating and heat transfer coupled results of hypersonic vehicle wing model were calculated. The results show that, for the low-curvature region, such as fuselage or center-section wing, structure deformation has little effect on temperature field. However, for the stagnation region with high curvature, the coupled effect is not negligible. Thus, it is quite important for the structure temperature prediction to take into account the effect of elastic deformation. This work has laid a solid foundation for improving the prediction accuracy of the temperature distribution of aircraft structures and the evaluation capacity of structural performance.
Abstract: The waverider is proved to be a remarkably useful
configuration for hypersonic glide vehicle (HGV) in terms of the high
lift-to-drag ratio. Due to the severe aerodynamic heating and the
processing technical restriction, the sharp leading edge of waverider
should be blunted, and then the flow characteristics and the
aerodynamic performance along the trajectory will change. In this
paper, the flow characteristics of a HGV, including the rarefied gas
effect and transition phenomenon, were studied based on a reference
trajectory. A numerical simulation was carried out to study the
performance of the HGV under a typical condition.
Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: A parallel computational fluid dynamics code has been
developed for the study of aerodynamic heating problem in hypersonic
flows. The code employs the 3D Navier-Stokes equations as the basic
governing equations to simulate the laminar hypersonic flow. The cell
centered finite volume method based on structured grid is applied for
spatial discretization. The AUSMPW+ scheme is used for the inviscid
fluxes, and the MUSCL approach is used for higher order spatial
accuracy. The implicit LU-SGS scheme is applied for time integration
to accelerate the convergence of computations in steady flows. A
parallel programming method based on MPI is employed to shorten
the computing time. The validity of the code is demonstrated by
comparing the numerical calculation result with the experimental data
of a hypersonic flow field around a blunt body.
Abstract: In the present study, the surface temperature history of the adaptor part in a two-stage supersonic launch vehicle is accurately predicted. The full Navier-Stokes equations are used to estimate the aerodynamic heat flux and the one-dimensional heat conduction in solid phase is used to compute the temperature history. The instantaneous surface temperature is used to improve the applied heat flux, to improve the accuracy of the results.
Abstract: This paper proposes the concept of aerocapture with
aerodynamic-environment-adaptive variable geometry flexible
aeroshell that vehicle deploys. The flexible membrane is composed
of thin-layer film or textile as its aeroshell in order to solve some
problems obstructing realization of aerocapture technique.
Multi-objective optimization study is conducted to investigate
solutions and derive design guidelines. As a result, solutions which
can avoid aerodynamic heating and enlarge the corridor width up
to 10% are obtained successfully, so that the effectiveness of this
concept can be demonstrated. The deformation-use optimum
solution changes its drag coefficient from 1.6 to 1.1, along with the
change in dynamic pressure. Moreover, optimization results show
that deformation-use solution requires the membrane for which
upper temperature limit and strain limit are more than 700 K and
120%, respectively, and elasticity (Young-s modulus) is of order of
106 Pa.